STMicroelectronics STM32 Development Board Module
위에view
This manual covers the STM32H743XIH6 / STM32H743 FK743M4-XIH6 / FK743M5-XIH6 core system learning development board module, including key manufacturer details, safety/compliance information, and general setup and operation guidance.
명세서
| 제품 이름 | STM32H743XIH6 STM32H743 FK743M4-XIH6 FK743M5-XIH6 Core System Learning STM32 Development Board Module Compatible with OpenMV LCD |
|---|---|
| Model (as listed) | STM32H743XIH6; STM32H743 FK743M4-XIH6; FK743M5-XIH6 (also shown as FK743M4-XIH6 / FK743M5-XIH6) |
| 배치/일련번호 | 1005008125910683 |
| 규정 준수 | CE (2014/35/EU Low Voltage Directive; 2014/30/EU EMC Directive) |
| 로이스 | Complies with Directive 2011/65/EU and amendment (EU) 2015/863 |
이 항목에 대한 정보
- High-performance foundation line, ARM Cortex-M4 core with DSP and FPU, 512 Kbytes Flash, 180 MHz CPU, ART Accelerator, Dual QSPI
- On-board ST-LINK/V2-1 debugger/programmer with SWD connector
- Can be powered from USB
- Three LEDs, Two Push-buttons
- Support of wide choice of Integrated Development Environments (IDEs) including IAR, ARM Keil, GCC-based IDEs
설치 
- 사용하기 전에 모든 지침을 읽으세요.
- Before integrating the module, ensure the operational environment aligns with the specified technical parameters and verify compatibility with existing systems.
- Follow established procedures for component placement and connection, and handle the product properly to avoid damage or performance degradation.
- During operation, keep conditions within the prescribed ranges and monitor performance indicators.
- Perform routine maintenance and periodic inspections; store the product in a dry place and keep it away from children.
- 경고: Keep the device and its cord out of reach of children under 3 years old.
- Keep away from children unless supervised by an adult.
- 본 제품을 원래의 용도 이외의 용도로 사용하지 마십시오.
- Inspect the product before each use; do not use if damaged.
- Follow installation and operation guidelines to avoid injury.
- 물이나 습기에 노출시키지 마십시오.
일반 지침
일반 지침
This product is designed and manufactured in accordance with industry-standard specifications to ensure optimal performance and reliability. Users are expected to adhere to the following guidelines to maximize component functionality and service life.
설치 과정
Follow established procedures for component placement and connection. Proper handling is essential to maintain integrity and prevent potential performance degradation.
운영 참고 사항
During use, maintain conditions within the prescribed ranges. Continuous monitoring of performance indicators is advised to sustain operational excellence.
유지관리 및 관리
Implement routine maintenance protocols to uphold product standards. Periodic inspections are encouraged to ensure ongoing compliance with quality expectations. Store it in a dry place. Keep away from children.
부인 성명
The manufacturer assumes no liability for outcomes resulting from non-compliance with these instructions, improper use, or unauthorized modifications. Specifications are subject to change without prior notice.For further details, consult the official documentation or contact our support team.
문제 해결
- Device damaged or shows issues before use: Inspect the product before each use; do not use it if damaged.
- Safety-related concerns during operation: Do not expose the product to water or moisture; follow installation and operation guidelines to avoid injury.
- Problems potentially related to setup: Review pre-installation considerations—ensure the operational environment matches specified technical parameters and that compatibility with existing systems has been verified.
문서 / 리소스
 | STM32 Development Board Module |
참고문헌
- 사용자 설명서manual.tools