ZigBee 3.0 Wireless Push Button Smart Scene Switch Controller User Manual

ZigBee 3.0 Wireless Push Button Smart Scene Switch Controller

제품 정보

특징

• iOS 폰/안드로이드 폰으로 제어 가능
• “스마트 라이프”와 “투야 스마트” 앱을 지원해주세요
• Voice control: Compatible with Alexa and Google home T mall Genie or Xiaodu speakers
• 타이밍 기능: 타이밍 기능으로 자동 온/오프
• 기존 기계식 스위치를 쉽게 교체할 수 있는 과부하 보호(중립 필요)
• 스마트 장면
• 장치 그룹

보안 정보

Risk of electric shock: Electricity can cause personal injury and properly damage if not handled properly. If you are unsure of any part of these instructions, seek professional help from a qualified electrician.

설치하다

알아채다:

• 배선하기 전에 회로 차단기의 전원이 꺼져 있는지 확인하십시오.
• Neutral wire is required. Verify that the wall box contains a neutral wire (usually white). If the wall box does not have a neutral wire, try another location in the home or call a professional electrician to install the switch.
• 본 설명서에 표시된 전선 색상은 일반적인 색상이며 일부 주택에서는 다를 수 있습니다.
• Make sure the wire conductors are securely attached to each screw.
• 배선하기 전에 Wi-Fi 신호가 안정적이고 제대로 작동하는지 확인하세요.
• 배선 경험이 없는 경우 전문 전기 기술자에게 문의하십시오.

첫 번째 단계:

• 회로 차단기를 끄고 전기 테스터로 전원을 테스트하십시오.
• 배선하기 전에 스위치가 꺼져 있는지 확인하십시오.

두 번째 단계:

• Remove existing wall panels; turn on power at breaker and use electrical tester to check which wire is the line; the tester will beep when near the line.
• Turn off the power at the circuit breaker; if there is a power outage, use an electrical tester, pull the existing switch out; mark the wiring and other wires; disconnect the power with pliers and remove the wires from the existing switch.
• Connect the switch wires to the wall box with the wire conductors according to the wiring diagram below.
• 세 번째 단계: Install the switch using the screws provided and snap the wall plate onto it.
• 네 번째 단계: 회로 차단기의 전원을 다시 켠 다음 조명을 켜십시오.

배선도

The Live wire is connected to the “L” terminal, The Neutral wire is connected to the “N” terminal, Lighting wire is connected to “L1, L2, L3” terminals.

1. Gang switch lighting wire connection: “L1” terminal
2. Gang switch lighting wire connection: “L1,L2” terminals
3. Gang switch lighting wire connection: “L1,L2,L3” terminals

장치 추가

Add device to “Smart Life” or “Tuya Smart” APP

1. Step 1: Download and install the “Smart Life” or “Tuya Smart” APP: Scan the QR code below
   
2. Step 2: Enter the phone settings option, turn on the Bluetooth and WiFi functions, and turn on the product at the same time
3. 3단계: 스마트 라이프 앱을 열고 계정을 등록한 후 로그인하세요. 이미 스마트 라이프 계정이 있는 경우 로그인만 하면 됩니다.
4. Step 4: Power on after the wiring is completed, the device is powered on by default, press and hold the touch wall switch button for about 8, until the WiFi blue LED flashes quickly, enter the network configuration mode
5. Step 5: Enter the App, click the “+” at the top right of the page to enter the network connection page.
6. Step 6: Make sure your device’s light is blinking quickly(2 times per second) tap to proceed to the next steр.
7. Step 7: Enter your WiFi and password
8. 8단계: 기기 이름을 지정하세요.
9. Step 9: When the WiFi LED is on, the device is online.
   지금 제어하세요!

How to use smart speakers to control devices, such as Amazon Alexa, Google Assistant or T mall Genie?
Smart Life 앱을 열고 "나"를 입력하세요. view and find the user Quide for “Me” view and find the user guide the corresponding smart speaker

【Note: Before using the smart speaker, please log in to your account on Amazon Alexa Google Assistant, or T mall Genie.]

RF 원격 제어 작동법 소개

Packaged products are paired at the factory and do this wirelessly. If you need to add or replace the remote control switch, please refer to the following steps

페어링 방법
Press and hold the touch wall switch button for about 3 seconds. The red LED indicator lights up to enter the RF433 pairing mode. At this time, press the RF433 remote control switch a few times and the indicator light flashes off. The switch is controlled and paired successfully.

코드 삭제 방법

Long press the touch wall switch button for 5 seconds until the red LED indicator flashes 3 times, the code is cleared successfully.