XTOOL XTS500 Wireless Diagnostics Module

명세서

• Operating temperature： 0~40℃
• Dimensions (W x H x D)：50 × 86.28× 25.50（mm）

제품 사용 지침

무선 연결

1. Connect OBDII-16 port of VCI Box to the vehicle’s DLC port.
2. Plug the USB wireless receiver into the USB port of the PC.
3. Go to the Wi-Fi selection page of your PC. Select WLAN 2 and search for the Wi-Fi hotspot with the same name as the SN of the device.
4. Once connected, your PC has established a connection with the device.

유선 연결

1. Connect OBDII-16 port of VCI Box to the vehicle’s DLC port.
2. Connect the VCI and the diagnostic PC with a USB Type-C cable.

진단 시 주의사항

• Ensure proper connections are made and follow safety protocols while performing diagnostics on vehicles.

About J2534 Toolbox
To install J2534 Toolbox:

1. QR코드를 스캔하거나 방문하세요
   https://www.xtooltech.com/english/DownloadCenter.html to find the installation pack.
2. 다운로드한 것을 압축 해제합니다 file and run Setup.exe. Follow the installation process.
3. After installation, restart your PC for changes to take effect.

사용 방법
To use J2534 Toolbox:

• For wired connection: Directly connect the VCI to the diagnostic PC via USB cable. The Toolbox will detect the device automatically.
• If not detected, click the Refresh button to try again.
• For wireless connection: Plug in the WiFi Receiver, click the WiFi button, select WLAN 2, find the matching hotspot, and connect.
• Ensure a stable connection before proceeding with diagnostics.

상표
XTOOL is a trademark of Shenzhen Xtooltech Intelligent Co., Ltd. Copyright, registered in China, the United States, and other countries. All other marks are trademarks or registered trademarks of their respective holders.

보증 부인 및 책임 제한
All information, specifications and illustrations in this manual are based on the latest information available at the time of printing. Xtool reserves the right to make changes at any time without notice. While information of this manual has been carefully checked for accuracy, no guarantee is given for the completeness and correctness of the contents, including but not limited to the product specifications, functions, and illustrations. Xtool will not be liable for any direct, special, incidental, or indirect damages, or for any economic consequential damages (including the loss of profits) as a result of using this product.

• Before operating or maintaining this unit, please read this manual carefully, please pay extra attention to the safety warnings and precautions.

지원 및 서비스

• 공식적인 Web대지: www.xtooltech.com
• 이메일: xtoolinplusus@outlook.com

일반 소개

아웃룩 및 포트

1. OBDII-16 port: Connect to vehicle’s DLC port.
2. Nameplate: Show device information.
3. Type-C Port: Connect the device to diagnosis PC via wire.
4. Indicator Light: Show device status.

표시등 색상	표시등 의미
녹색 불빛이 켜짐	전원 켜짐
녹색 불빛이 깜박임	펌웨어 업데이트
솔리드 블루 라이트	Device connected (no communication)
깜박이는 파란색 빛	Communicating with the vehicle
깜빡이는 빨간불	장치 오류

시작하기

 차량 연결

무선 연결

1. Connect OBDII-16 port of VCI Box to vehicle’s DLC port.
2. Plug the USB wireless receiver into the USB port of the PC.
3. Go to Wi-Fi selection page of your PC. Select “WLAN 2”, and search for the Wi-Fi hotspot that has the same name as the SN of the device.
4. Once the hotspot is connected, your PC has established connection with the device.

유선 연결

1. Connect OBDII-16 port of VCI Box to vehicle’s DLC port.
2. Connect the VCI and the diagnostic PC with a USB Type-C cable.

진단 시 주의사항

1. 권tag자동차의 e 범위: +9~+36V DC;
2. When testing some special functions, the operator must operate according to the prompts and meet the test conditions. In some cases, the conditions that need to be met are: engine water temperature 80 ℃~105 ℃, turn off headlights and air conditioners, keep the accelerator pedal in the released position, etc.;
3. 다양한 모델의 전자 제어 시스템은 매우 복잡합니다. 테스트가 불가능하거나 많은 양의 테스트 데이터가 비정상적인 상황이 발생할 경우 차량의 ECU를 검색하여 ECU 명판에서 해당 모델에 대한 메뉴를 선택할 수 있습니다.
4. 차량이나 장치의 손상을 방지하기 위해 XTOOL에서 제공하고 장치에 맞게 설계된 배선 하네스만 이 장치와 함께 사용할 수 있습니다.
5. When running a diagnostics session, DO NOT shut down the device directly. You should cancel the task before returning to the main interface and then shutting down the device.

About J2534 Toolbox
J2534 Toolbox is a PC application that manage the updates and operation logs for all VCIs that supports J2534 function. Before you start working on diagnostics with your PC, make sure you have the J2534 Toolbox installed.

설치

• Scan the QR code on the right, or go to:https://www.xtooltech.com/english/DownloadCenter.html
• And find “J2534 Toolbox” for the installation pack.
• After the download is completed, unzip it and click “Setup.exe”, then follow the installation process. We suggest you to restart your PC after installation.

사용 방법

• The picture on the right shows the main screen of the J2534 Toolbox when the VCI is not connected to the diagnostic PC.

Device Connection – Wired

• Directly connect the VCI to the diagnostic PC via USB cable. The Toolbox will automatically detect the device when you connect it.
• If the status has not been refreshed after you connect the VCI via wire, click the Refresh button to try again.

Device Connection – Wireless

1. Plug in the WiFi Receiver that comes with the VCI box.
2. Click the WiFi button on the bottom-left corner and select “WLAN 2” (or other numbers)
3. Find the hotspot that names the same as the SN of the VCI box and click “Connect”.
4. When the connection is ready, you are OK to go.

메인 화면
When the VCI is connected, you will see this screen:

• SN: Shows the SN of the current VCI.
• Firmware Version: Shows current firmware version that is installed on the VCI.
• Driver Version: Shows current driver version that is installed on the VCI.
• J2534 Authorization: Shows the VCI authorization status of current VCI.

• Log Record: Turn on/off the J2534 communication logs recording.
• Feedback: Send feedback to XTool customer service team when you meet any issues regarding the J2534 connection.

Firmware/Driver Update

• If there is an update for the firmware or the driver, you will see a red dot beside the version number. Click the Update button on the right to check updates.
• You can choose the version first, and click “Upgrade” button on the right to start updates.
• DO NOT DISCONNECT THE VCI WHEN THE UPDATE IS IN PROGRESS!

설정

• Click the “Settings” button on the top-right corner and go to the Toolbox settings.
• Languages: Click to change language shown on the Toolbox.
• Version Number: Check the updates of the Toolbox.
• Log Cache: Show the size of the log folder. You can click the button on the right to clear all logs.
• Save Location: This shows the location of the log folder. You can click this to get into the folder.

• DoIP Mode Switch: When there are cases that the vehicle asks for a DoIP connection, please turn on the switch to enable DoIP mode. Please note that the DoIP mode can only be enabled in wired connection.

피드백

If you meet any issues regarding J2534 connection, please record the logs (turn on the log recording switch) and send the logs to XTool customer service team. To better locate your problems, we need the following information in the report:

• 귀하의 이메일 주소
• 통나무 files, recorded when the issues happened
• Vehicle information (brand, model, MY)
• Firmware/Driver version info
• A brief description on what is going on (you can also attach images & screenshots)

Our customer service team will handle this and reply to you via email.

FCC 준수

• FCC ID: 2AW3IV01W2

이 장치는 FCC 규정 제15부를 준수합니다. 작동은 다음 두 가지 조건에 따릅니다.

1. 이 장치는 유해한 간섭을 일으키지 않습니다.
2. 이 장치는 원치 않는 작동을 일으킬 수 있는 간섭을 포함하여 수신되는 모든 간섭을 수용해야 합니다.

경고
규정 준수에 책임이 있는 당사자의 명시적 승인 없이 변경이나 수정을 하는 경우 사용자의 장비 작동 권한이 무효화될 수 있습니다.

메모
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment can generate, use and radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• 수신 안테나의 방향을 바꾸거나 위치를 바꾸세요.
• 장비와 수신기 사이의 거리를 넓힙니다.
• 수신기가 연결된 것과 다른 회로의 콘센트에 장비를 연결하세요.
• 도움이 필요하면 딜러나 숙련된 라디오/TV 기술자에게 문의하세요.

책임 당사자

• 회사 이름: FCC US Agent, LLC
• 주소: 3722 Illinois Avenue, Saint Charles, IL, 60174, USA
• 이메일: 지원@FCCUSAgent.com

ISED 성명

• IC: 29441-V01W2
• Model: XTS500
• PMN: V120，XTS500
• HVIN: V01W2A

이 장치에는 혁신, 과학 및 경제 개발 캐나다의 면허 면제 RSS를 준수하는 면허 면제 송신기/수신기가 포함되어 있습니다. 작동은 다음 두 가지 조건에 따릅니다.

1. 이 장치는 간섭을 일으켜서는 안 됩니다.
2. 본 장치는 원치 않는 작동을 일으킬 수 있는 간섭을 포함한 모든 간섭을 허용해야 합니다.

CE

• 적합성 선언
• 심천 XTOOLtech Intelligent Co., Ltd는 본 무선 진단 모듈이 지침 2014/53/EU의 필수 요건 및 기타 관련 규정을 준수함을 선언합니다. 제10조(2)항 및 제10조(10)항에 따라 본 제품은 모든 EU 회원국에서 사용할 수 있습니다.

영국 여성 협회

• 이에 따라, 심천 XTOOLtech Intelligent Co., Ltd는 이 무선 진단 모듈이 영국 무선 장비 규정(SI 2017/1206), 영국 전기 장비(안전) 규정(SI 2016/1101), 영국 전자기 적합성 규정(SI 2016/1091)의 범위 내에서 제품에 적용되는 모든 기술 규정을 충족함을 선언하며, 동일한 신청이 다른 영국 승인 기관에 접수되지 않았음을 선언합니다.
• 심천 Xtooltech 지능형 Co., Ltd.
• 추가: 중국 심천시 난산구 Liuxian Avenue Creative City A17 빌딩 18&2/F
• 심천 본사 전화: +86 755 2399608
• 이메일: Marketing@xtooltech.com

자주 묻는 질문

What operating system does XTS500 J2534 support?

The device only support Windows 7/8/10/11 or later version.

Why can’t my Mac recognize this device?

The device does not support macOS system.

Does the device need to be activated for usage?

This device need no S/N or activation code to activate the device. It will work directly with OE software once connection.

What functions can this device achieve?

This device can do what OE dignostic software do. Please check the compatibility before usage.

Dose the device include OE software?

OE software is not included in the package. You need to subscribe the OE software from manufacturer.

문서 / 리소스

XTOOL XTS500 Wireless Diagnostics Module [PDF 파일] 사용자 매뉴얼 XTS500 Wireless Diagnostics Module, XTS500, Wireless Diagnostics Module, Diagnostics Module, Module

참고문헌

• 사용자 설명서