UFO CC10 다기능 LED 드라이버 사용 설명서

This guide contains important safety information and installation instructions.
Please read fully before installing, operating or performing any maintenance on the product.

Introduction & Safety

구매해주셔서 감사합니다asing the UFO CC10 LED driver. This user guide contains important information and should be read fully before any installation work commences. Please keep for future reference. The CC10 is a compact 350mA, 500mA, 700mA and 1000mA output constant current multi-function driver designed to drive UFO constant current LED fittings up to 50W. Constant voltage LEDs cannot be connected to this driver. Please refer to the specific section within this manual for wiring and connection guidance.

중요한
This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product, its component parts and the hazards involved. Electrical wiring and connection must be carried out by a suitably qualified person observing all local and statutory electrical regulations. The CC10 driver is suitable for use only with a class 2 power unit.

중요한 안전 정보
This driver is designed to work with constant current LED fittings operating on a 350mA, 500mA, 700mA or 1000mA output. Connecting this driver to any other LED devices may result in catastrophic failure of the LED device and/or the CC10 driver. Always check the input current and voltage of the LED devices to ensure compatibility prior to powering up the system. Never hot swap LED fittings. When adding or removing LED fittings always power down the system first. This driver is designed to work on a DC input voltage of 12-48V ONLY. The DC PSU supplying this driver must have an output capability sufficient to power up the driver and maintain the output load. The CC10 driver is suitable for indoor/dry areas and must not be installed in damp 또는 습한 환경.

출력 용량

The UFO Unidrive CC10 driver supplies a constant current of 350mA, 500mA, 700mA or 1000mA at output voltages between 3.2 and 48V. UFO fittings operate on a max. voltage of 3.2V DC and provide a 1.1W output. The UFO Unidrive CC10 driver has a low voltage DC input. Therefore the PSU used to supply the CC10 is selected based upon the total number of fittings the CC10 will be driving.

LED 수 피팅	Max Volts DC	Total Watts DC (350mA)	Total Watts DC (500mA)	Total Watts DC (700mA)	Total Watts DC (1000mA)	Standard UFO PSU Paired with an IEC cable for either UK, EU or USA
1	3.6	3.6	4.2	5.1	6.3	702070 12V 5A 60W PSU
2	7.2	4.6	5.6	7.2	9.4	702070 12V 5A 60W PSU
3	10.8	5.5	6.9	9.2	9.5	702070 12V 5A 60W PSU
4	14.4	9.4	11.5	14.8	19.0	700994 24V 3.75A 90W PSU
5	18.0	10.4	13.0	16.9	22.0	700994 24V 3.75A 90W PSU
6	21.6	14.0	17.1	21.9	27.9	700485 36V 1.66A PSU
7	25.2	14.9	18.4	24.0	30.9	700485 36V 1.66A PSU
8	28.8	15.9	19.8	26.0	33.9	700485 36V 1.66A PSU
9	32.4	19.6	24.3	31.4	40.5	700485 36V 1.66A PSU
10	36.0	20.7	25.7	33.6	43.5	700485 36V 1.66A PSU
11	39.6	21.6	26.9	35.5	46.3	708120 48V 0.5A 25W PSU
12	43.2	22.6	28.3	37.5	49.2	708120 48V 0.5A 25W PSU

중요한

Connecting too many constant current LED fittings to the CC10 driver with excessive maximum voltage output or using an underrated PSU will result in the driver shutting down. Always check the maximum output voltage of the fittings and ensure that based on 3.6V per LED an adequate number of fittings are connected, and a suitable rated input PSU for the CC10 driver is selected, prior to powering up the system.

기능 정보

Driver PCB Layout

Refer to the table below for description of each part.

장치	기능
A	Power input jack socket (2.5mm centre positive). DC input voltage 12V to 48V dependent on number of LED fittings connected
B	DMX input/output screw terminals. Data positive, data negative and ground. Occupies two DMX channels – Channel 1 – LED dimming, Channel 2 LED ON/OFF. Use for DMX control or Primary/Secondary link to other CC10 drivers
C	Function LED – indicates signal and control presence
D	Power and fault LED – indicates power input and overcurrent, short circuit and over temperature faults (flashing)
E	Function DIP switch – sets different functions (manual, DMX, sensor input etc.) and also addressing for DMX. Switch down for ON up for OFF
F	0-10V input screw terminals. Positive and negative current source (external receiving voltage) 0-10V dimming voltage input (0 to 100%)
G	Manual (current sink) dimming screw terminals – 10V on screw terminals adjusted by external electronic potentiometer. Normally linked out when not in use
H	Constant current screw terminal output LED + and common ground
J	Set Current. 350mA, 500mA, 700mA or 1000mA. Fit one link only
K	FADE IN potentiometer. Adjusts the fade in time for sensor operation between 1 and 12 seconds
L	DELAY potentiometer. Adjusts the on time for sensor operation (between fade in and fade out) from 1 sec to approximately 5 minutes
M	FADE OUT potentiometer. Adjusts the fade out time for sensor operation be- tween 1 and 12 seconds
N	Sensor input – one normally open (N/O – goes open circuit to trigger FADE IN) one normally closed (N/C – goes closed circuit to trigger FADE IN)

일반적인 배선 연결

중요한

Connect ALL LEDs, electrical control and output wiring connections for the complete system BEFORE setting up the driver and connecting the driver PSU to the mains supply.
Never hot swap LED fittings. When adding or removing LED fittings always power down the system first.

드라이버 설정

ALWAYS carry out ALL wiring connections, set current (350mA, 500mA, 700mA or 1000mA) and set up the appropriate functionality (see below) prior to connecting power to the driver.

Non Dimming Operation
For non dimming operation, all of the manual and remote controls are disabled.

Manual Dimming Operation – Current Sink
For manual dimming using an electronic potentiometer, the current sink screw terminal link must first be removed – and a potentiometer connected, in its place. Only compatible electronic potentiometers recommended by UFO are to be used.

0-10V Dimming – Current Source
0-10V dimming (current source) requires an external varying 0 to 10V DC control voltag이자형. 제어 권tage will dim both LED outputs simultaneously. See 0-10V value table on following pages. For remote dimming using 0-10V, the current sink screw terminal link must first be inserted.

DMX Dimming & Control

메모:
The CC10 driver occupies two DMX channels – see DMX Channel Table.
For guidance on DMX address switch settings see DMX Address Table.

XNUMX 차 제어

보조 제어

센서 입력

Sensor input may either be Normally Open (N/O) or Normally Closed operation. For N/O operation the sensor must go open circuit to operate the driver. For N/C operation the sensor must go closed circuit to operate the driver.
The sensor circuit has three timers FADE IN, DELAY & FADE OUT. These timers are adjusted by trimmer potentiometers (K, L & M), see sensor table on opposite page.

메모:
Where a movement sensor is used to trigger the input, the DELAY and FADE OUT timers will not run to completion until all movement has ceased.

Information Tables

DMX 채널 테이블

채널 번호	기능	값
01	LED Output Dimming	0-255 – No light to maximum light output
02	LED Output On	0-250
02	LED Output Off	251-255

0-10V Current Source Value Table

Value -DC Volts	설명
0 – 0.47	LED Output Off
0.48	LED Output Minimum Illumination
10	LED Output Maximum Illumination

센서 테이블

낚시찌	범위(대략)	설명
페이드 인	1~10초	On sensor operation, fades in LED output from no light to maximum light
지연	1~300초	Maintains LED output at maximum light
페이드 아웃	1~10초	After delay, timer fades out LED output from maximum light to no light

메모:
The trimmer potentiometers are set for minimum (seconds) at full counter clockwise rotation, maximum seconds) at full clockwise rotation.

DMX Address Tables

Dip Switches S6 to S9

DIP 스위치 설정 0=꺼짐 1=켜짐					S9	0	0	0	0	0	0	0	0	1	1	1	1	1	1	1	1
					S8	0	0	0	0	1	1	1	1	0	0	0	0	1	1	1	1
					S7	0	0	1	1	0	0	1	1	0	0	1	1	0	0	1	1
					S6	0	1	0	1	0	1	0	1	0	1	0	1	0	1	0	1
S1	S2	S3	S4	S5
0	0	0	0	0		0	32	64	96	128	160	192	224	256	288	320	352	384	416	448	480
1	0	0	0	0		1	33	65	97	129	161	193	225	257	289	321	353	385	417	449	481
0	1	0	0	0		2	34	66	98	130	162	194	226	258	290	322	354	386	418	450	482
1	1	0	0	0		3	35	67	99	131	163	195	227	259	291	323	355	387	419	451	483
0	0	1	0	0		4	36	68	100	132	164	196	228	260	292	324	356	388	420	452	484
1	0	1	0	0		5	37	69	101	133	165	197	229	261	293	325	357	389	421	453	485
0	1	1	0	0		6	38	70	102	134	166	198	230	262	294	326	358	390	422	454	486
1	1	1	0	0		7	39	71	103	135	167	199	231	263	295	327	359	391	423	455	487
0	0	0	1	0		8	40	72	104	136	168	200	232	264	296	328	360	392	424	456	488
1	0	0	1	0		9	41	73	105	137	169	201	233	265	297	329	361	393	425	457	489
0	1	0	1	0		10	42	74	106	138	170	202	234	266	298	330	362	394	426	458	490
1	1	0	1	0		11	43	75	107	139	171	203	235	267	299	331	363	395	427	459	491
0	0	1	1	0		12	44	76	108	140	172	204	236	268	300	332	364	396	428	460	492
1	0	1	1	0		13	45	77	109	141	173	205	237	269	301	333	365	397	429	461	493
0	1	1	1	0		14	46	78	110	142	174	206	238	270	302	334	366	398	430	462	494
1	1	1	1	0		15	47	79	111	143	175	207	239	271	303	335	367	399	431	463	495
0	0	0	0	1		16	48	80	112	144	176	208	240	272	304	336	368	400	432	464	496
1	0	0	0	1		17	49	81	113	145	177	209	241	273	305	337	369	401	433	465	497
0	1	0	0	1		18	50	82	114	146	178	210	242	274	306	338	370	402	434	466	498
1	1	0	0	1		19	51	83	115	147	179	211	243	275	307	339	371	403	435	467	499
0	0	1	0	1		20	52	84	116	148	180	212	244	276	308	340	372	404	436	468	500
1	0	1	0	1		21	53	85	11	149	181	213	245	277	309	341	373	405	437	469	501
0	1	1	0	1		22	54	86	118	150	182	214	246	278	310	342	374	406	438	470	502
1	1	1	0	1		23	55	87	119	151	183	215	247	279	311	343	375	407	439	471	503
0	0	0	1	1		24	56	88	120	152	184	216	248	280	312	344	376	408	440	472	504
1	0	0	1	1		25	57	89	121	153	185	217	249	281	313	345	377	409	441	473	505
0	1	0	1	1		26	58	90	122	154	186	218	250	282	314	346	378	410	442	474	506
1	1	0	1	1		27	59	91	123	155	187	219	251	283	315	347	379	411	443	475	507
0	0	1	1	1		28	60	92	124	156	188	220	252	284	316	348	380	412	444	476	508
1	0	1	1	1		29	61	93	125	157	189	221	253	285	317	349	381	413	445	477	509
0	1	1	1	1		30	62	94	126	158	190	222	254	286	318	350	382	414	446	478	510
1	1	1	1	1		31	63	95	127	159	191	223	255	287	319	351	383	415	447	479	511

Switches S1 to S5 / DMX Address

문제 해결

문제	가능한 원인	치료
	주전원 공급 꺼짐	공급품 확인 및 복원
[일반적인] System is dead – power LED (D) not lit. No light output from LED	느슨한 주 플러그	플러그를 확인하세요
	Loose DC output wire or connection	모든 연결을 확인하세요
	PSU failed – check output	PSU 교체
	with DVM
	Driver PCB failure	드라이버 교체
[일반적인] One output channel is dead Power LED (D) is lit	Loose output wire to dead channel or faulty/poorly fitting power in on extrusion. Check output with DVM	모든 연결을 확인하세요
[일반적인] One output channel is dead Power LED (D) is lit	Driver PCB failure	드라이버 교체

[NO DIMMING MODE] System is dead – power LED (D) lit.	Current sink input link in place – DIP switch 10 on	Switch 10 off or remove link
[NO DIMMING MODE] System is dead – power LED (D) lit.	Loose output GND wire or poorly fitting power in on extrusion	모든 연결을 확인하세요
빛 출력 없음	PSU failed – check output with DVM	PSU 교체
	Driver PCB failure	드라이버 교체

[MANUAL DIMMING MODE]

Power LED (D) lit – function LED

Switch 10 off Switch 10 to on

Electronic potentiometers Check polarity of

wired incorrectly – wrong connections and reconnect

polarity correctly.

[0-10V DIMMING MODE] Power LED (D) lit – function LED (C) not lit. Output LED devices illuminated but not dimming	Switch 10 is off	Switch 10 to on
[0-10V DIMMING MODE] Power LED (D) lit – function LED (C) not lit. Output LED devices not illuminated	0-10V wired incorrectly – wrong polarity	Check polarity of connections and reconnect correctly
	0-10V control signal missing check input with DVM	Check all connections and output of 0-10v controller using DVM
[0-10V DIMMING MODE] Power LED (D) lit – function LED (C) lit. Output LED devices illuminated but flickering	0V from 0-10V control signal is missing	Check all connections and output of 0-10V controller using DVM

문제	가능한 원인	치료
[DMX DIMMING MODE] Power LED (D) lit – function LED (C) lit. Output LED devices illuminated but not responding to DMX	DMX address not set on DIP switches 1-9	DMX 주소 설정
[DMX DIMMING MODE] Power LED (D) lit – function LED (C) lit. Output LED devices not illuminated and not responding to DMX	Switch 10 is on	Switch 10 off
	Incorrect DMX address set	Set correct DMX address
[DMX DIMMING MODE] Power LED (D) lit – function LED (C) not lit. Output LED devices illuminated but not responding to DMX	DMX control signal missing	Check all connections are secure and correct polarity and confirm output of DMX controller and/or previous DMX device in DMX chain

[SECONDARY MODE] Power LED (D) lit – function LED (C) not lit. Output LED devices illuminated but not responding to master control	Primary driver not set up correctly	Check primary driver set up
	DMX control signal from primary driver missing	Check all connections are secure and correct polarity and confirm output of primary driver and/or previous devices in primary / secondary DMX chain

[N/O or N/C SENSOR OPERATION] Power LED (D) lit – function LED (C) not lit. Output LED devices illuminated but not responding to sensor	Switch 10 is off	Switch 10 to on
[N/O SENSOR OPERATION] Power LED (D) lit – function LED (C) not lit. Output LED devices not illuminated and not responding to sensor	Switch 1 is off	Switch 1 to on
	Current sink input link in place	링크 삭제
[N/C SENSOR OPERATION] Power LED (D) lit – function LED (C) not lit. Output LED devices not illuminated and not responding to sensor	Switch 2 is off	Switch 2 to on
	Current sink input link in place	링크 삭제
[N/O or N/C SENSOR OPERATION] Power LED (D) lit – function LED (C) not lit. Output LED devices not illuminated and not responding to sensor	Sensor control signal is missing	Check all connections and output of sensor using DVM
	Sensor wired to wrong input	Check input connections and rewire

문제	가능한 원인	치료
[SHORT CIRCUIT] Output LED devices go out and power LED (D) flashes rapidly	Short circuit between LED output and GND. Short circuit between LED1 output and/or LED 2 output and GND	Check for short circuit on output cables using a DVM. Repair or replace faulty cables or devices.

[OVER CURRENT]

Heavily loaded system – Output LED devices go out momentarily and power LED (D) flashes rapidly

System overloaded beyond 30W

Reduce load by removing some LED fittings until a safe working load of not more than 30W is achieved

[OVER TEMPERATURE]

Output LED devices go out momentarily and power LED (D) flashes rapidly

Driver ambient temperature too hot

Relocate driver to cooler ambient environment

기술 정보

제품 코드	DR-CC-DC-48-50-D-CU (driver with single integral dimming potentiometer) DR-CC-DC-48-50-ALL-CU (driver with fully functional manual / dmx / 0-10V / sensor control)
설명	50W fully functional dimmable constant current driver
입력 전원	12-48V DC
정격 전력	최대 출력 50W
출력 전류	350mA, 500mA, 700mA, 1000mA
연결	Power – 2.1mm input jack plug Control & Outputs – screw terminals
보호	SCP / OCP / OTP
기능성	Individual manual (current sink) dimming with electronic potentiometer 0-10V (current source) output dimming DMX with 2 channels (LED dimming & on/off). Controllable from DMX system or can operate standalone master/slave with other CC10 drivers. 2 channels (N/O & N/C) sensor input to trigger output LED devices with fade in, delay and fade out controls.
주변 온도	Min. -20°C to Max. +45°C
IP 등급	IP20은 실내에서만 사용 가능
치수	180mm(7.09인치) x 116.5mm(4.59인치) x 44.5mm(1.75인치)

연락하다

Universal Fibre Optics
Home Place
Coldstream, TD12 4DT
영국
+44 (0) 1890 883416
www.ufo.조명

Universal Fiber Optics USA

1749 Northgate Blvd
Sarasota, FL34238
미국
941-343-8115
www.광섬유조명.com

UFO 리히트 GmbH

Andreastraße 20
93059 레 겐스 부르크
독일
+49 (0) 9491 955880
www.ufo-licht.de

자주 묻는 질문

Q: What happens if I connect too many LED fittings or use an underrated PSU with the CC10 driver?

A: The driver may shut down to prevent damage. Always ensure the total number of fittings and the PSU rating are appropriate before powering up the system.

문서 / 리소스

UFO CC10 Multi Function Led Driver [PDF 파일] 사용자 가이드
CC10 Multi Function Led Driver, CC10, Multi Function Led Driver, Multi Function Led Driver, Function Led Driver, Led Driver, Driver

참고문헌

사용자 설명서

UFO CC10 Multi Function Led Driver

명세서