TRIGGERTECH T3 Diamond Trigger Instruction Manual

TRIGGERTECH T3 Diamond Trigger

명세서

• 제품 이름: TriggerTech Tikka Trigger
• 모델: T3, T3X & T1X
• 제품번호: [Insert SKU Serial #]
• Pull Weight Adjustment: 5/64 Allen

제품 정보

The TriggerTech Tikka trigger is designed for use in specific Tikka firearm models – T3, T3X & T1X. It comes with a safety lever that can be easily switched between safety on and safety off positions. The trigger features a sear, plunger, and trigger lever  for precise and reliable performance.

설치 지침

1. 1단계: Unload your firearm and remove the bolt and stock
   • Slide out the bolt
   • Remove action screws
2. 2단계: 준비
   • 설치 및 사용 전에 TriggerTech 면책 조항과 TriggerTech 평생 보증을 읽어보세요.
   • Remove all ammunition and magazines.
   • Remove the bolt from your firearm by pressing the bolt release while sliding the bolt aft-ward.
   • Using the appropriate Torx driver (typically T25), carefully remove your stock from the action. Note the size and location of each bolt for reassembly.

경고:

방아쇠를 제대로 설치하지 않고 안전 기능이 제대로 작동하지 않으면 총기가 안전하지 않을 수 있습니다. 모든 지침을 읽고 준수하십시오. 도움이 필요하면 TriggerTech 또는 공인 총포상에게 문의하십시오.

TriggerTech 면책 조항

Improper handling, installation, storage and/or use of TriggerTech products and/or the firearm in which they are installed, can cause death, serious injury and/or property damage.

TriggerTech products are designed solely for installation and use in the specific firearm for which they are advertised. It is the purchaser’s responsibility to determine compatibility. Aftermarket trigger handling and installation can involve complicated procedures and presuppose knowledge of firearms handling. If a purchaser or user s not familiar, or not sufficiently familiar, with firearms handling and exchanging out trigger components, the purchaser or user (collectively, “Purchaser”) must seek further information and assistance from a gunsmith or other qualified professional. By installing or using any purchased TriggerTech trigger product (“TT Product”) the Purchaser agrees to the following terms and conditions:

1. 구매자는 TT 제품을 취급, 설치, 보관 및/또는 사용하는 관할권에서 시행되는 모든 해당 총기 안전 법률, 프로토콜 및 규정을 준수해야 합니다.
2. 구매자는 TT 제품을 구매하고 사용할 법적 권한이 있으며, TT 제품을 구매하고 사용하는 관할권에서 해당 TT 제품과 해당 제품이 설치될 총기를 구매하고 사용할 법적 권한이 있음을 증명합니다.
3. The Purchaser assumes responsibility for ensuring that any users of the TT Product comply with these terms and conditions and with all applicable firearms safety protocols and regulations when  handling, installing, storing and/or operating the TT Product;
4. 구매자는 TT 제품을 사용하기 전에, 해당 제품이 장착된 총기에 장전되지 않은 상태에서 방아쇠의 적합성 및 기능 테스트를 실시하는 데 동의합니다. TT 제품을 테스트하지 않고 작동한다고 가정해서는 안 됩니다.
5. The Purchaser agrees to consistently use a trigger lock on the installed TT Product, together with any related safety mechanism on the firearm in which the TT Product is installed;
6. The Purchaser agrees to contact TriggerTech immediately in the event of any change or loss of trigger function;
7. Following installation, the Purchaser will not conduct any maintenance of the TT Product which requires disassembly of the TT Product, in whole or part;
8. In no event shall TriggerTech beliable for any direct, indirect, incidental, special, consequential or punitive damages arising from loss of life, personal injury and/or property damage, in connection with the use or misuse of the TT product, or the firearm in which the TT Product is installed;
9. TriggerTech is not responsible for the acts or omissions  f the Purchaser resulting from a lack of training or knowledge of firearms handling, or failure to properly implement such training and knowledge;
10. The Purchaser assumes the risk and all liability for death, injury, and loss and damage to persons or property caused by use or installation inconsistent with TriggerTech’s instructions, negligent or intentional use or misuse of the TT Product, or the firearm in which  the TT Product is installed.

보증

TriggerTech 제한 보증

TriggerTech warrants to the original retail purchaser that this TriggerTech product will be free from manufacturing and handling defects for thirty days after the original sale of the product, and from manufacturing defects for the life of the product. This warranty only applies if this product was manufactured and sold by TriggerTech. This warranty excludes conditions caused by excessive wear and tear, aggressive handling, unreasonable use, modifications, alteration, tampering, misuse, improper installation, or other factors outside TriggerTech’s control. Modifying the product in any way VOIDS this warranty. This limited warranty does not extend to future performance. No TriggerTech representative, distributor or reseller is authorized to assume any other obligation or liability in connection with the product, or to alter the terms of this warranty.

본 계약에 명시된 것 이외의 모든 보증은 관련 법률이 허용하는 범위 내에서 상품성 및 특정 목적에의 적합성에 대한 묵시적 보증을 포함하여 부인됩니다. 또한, 관련 법률이 허용하는 범위 내에서 우발적, 징벌적, 특별 또는 결과적 손해에 대한 모든 책임은 명시적으로 부인됩니다.

TriggerTech does not assume any liability arising from loss of life, personal injury and/or property damage in connection with the use, misuse or modification of the TT product, or the firearm in which the TT Product is installed. Warranties are handled directly by TriggerTech, not through our dealer network. To obtain warranty coverage, please contact us directly at the number/web반품 승인을 받으려면 아래 사이트를 방문하세요. 결함이 있는 제품은 검사를 위해 TriggerTech로 반품해야 합니다. 당사로의 배송비는 고객 부담입니다. TriggerTech에서 보증이 필요하다고 판단하는 제품은 TriggerTech의 단독 재량에 따라 교체 또는 수리됩니다.

메모: TriggerTech 트리거를 설치하면 총기 제조업체의 보증이 일부 또는 전부 무효화될 수 있으므로 트리거를 설치하기 전에 총기 제조업체에 문의하여 설치가 총기 보증에 영향을 미치는지 확인하세요.

TriggerTech 만족 보장

TriggerTech 트리거는 경쟁사 제품보다 확실히 덜 미끄러지는 느낌이 듭니다. 대부분의 사수들은 view this as a benefit, some may not enjoy the distinct, crisp feeling of a TriggerTech trigger. If you are the original purchaser and are not satisfied with the zero-creep break of your TriggerTech trigger, you may return it to
TriggerTech within thirty (30) days of purchase, in the original packaging and with proof of purchase. Provided the trigger is undamaged, TriggerTech will refund the purchase price.

지시 사용

TriggerTech Tikka trigger

• 1단계: Unload your firearm and remove the bolt and stock
  • 1a) Read TriggerTech Disclaimer and TriggerTech Lifetime Warranty prior to installation and use.
  • 1b) Remove all ammunition and magazines.
  • 1c) Remove the bolt from your rearm by pressing the bolt release while sliding the bolt aft-ward.
  • 1d) Using the appropriate Torx driver (typically T25), carefully remove your stock from the action.
    • 메모: Remember the size and location of each bolt you remove from the stock for reassembly.
• 2단계: Remove the existing trigger
  • Unscrew the trigger bolt with the appropriate screw driver (typically a Hex 5) to remove the trigger (trigger safety on).n).
• 3단계: Install your TriggerTech trigger
  • Insert the TriggerTech trigger assembly into the action with the trigger safety on. Using the same factory trigger bolt from Step 2. Tighten bolt to 55-65 in-lbs.
• 4단계: Re-install the stock and bolt
  • 4a) Using the same screws from Step 1, re-install your stock onto the action.
  • 4b) Insert the bolt and check the bolt release functionality. The bolt should only be removable while the bolt release is being pressed. When the bolt release is not being pressed, the bolt should not be removable.
• 5단계: Check trigger safety and function
  • Prior to using your firearm, perform the following tests without ammunition to see if your installation was done correctly.
  • 5a) Safety on and cycle action – firing pin should NOT move 5b) Safety of and cycle action – firing pin should NOT move
  • 5c) Safety on, cycle action, pull trigger lever – the ring pin and trigger lever should NOT move
  • 5d) Safety on, cycle action, pull trigger lever – firing pin should move
  • 5e) Safety on, cycle action, cycle safety to reposition – the ring pin should NOT move
  • 5f ) Safety on, cycle action, squeeze lever firmly (No audible clicks should be heard while squeezing the trigger lever), release lever, cycle safety to reposition – the ring pin should NOT move
  • 5g) Safety on, cycle action, and tap the butt-stock – firing pin should NOT move (NEVER PERFORM THIS STEP WITH LIVE AMMUNITION)
  • 5h) Safely repeat Steps 7a through 7f (and NOT 7g) at a rifle range with live ammunition with rifle pointed in a safe direction to ensure trigger installation was done correctly.
• 6단계: Pull weight adjustment
  • Your TriggerTech trigger is set near the middle of the advertised pull weight range and can be adjusted in increments. To adjust pull weight, insert the supplied 5/64” Allen wrench into the set screw located at the bottom of your trigger. To increase pull weight, rotate the set screw clockwise. Pull weight varies between actions.
• 경고: It is recommended to operate your trigger at, or above factory settings. Exercise caution when adjusting your pull weight and repeat Step 5 prior to using live ammunition.
• 메모: Always keep the set screw engaged with at least three “Clicks” to prevent the set screw from falling out

무게 조정 경고를 당깁니다

The TriggerTech Tikka trigger has an adjustable pull weight. The factory setting is near the middle of the advertised range (caution – pull weights may vary dramatically from the factory setting due to variability found in actions). There is such a thing as a trigger that is too light to be considered safe. This weight will change depending on the specifics of the gun, the experience of the shooter, and the intended use case (how the gun and all of its components are operated/handled). TriggerTech strongly recommends that you get some trigger time on your TriggerTech trigger before adjusting the break weight below the factory setting (a trigger set at 4.0  bs is safer than a trigger set at 2.5 lbs). As you reduce the pull weight of a TriggerTech Trigger, you are reducing the amount of spring tension in the trigger and it is possible that you may reach a point where the trigger in a specific gun is not safe for the intended use case and/or the shooter. Your trigger’s pull weight may change slightly over the trigger’s lifetime as the parts wear in. Any change should be gradual and not in excess of 6 oz or 15% (whichever is less). A change in excess of this range, or any sudden change, is a sign that something is not right, and your firearm may not be safe. Stop using your trigger and contactTriggerTech Support  (support@triggertech.com) 1-888-795-1485. TriggerTech recommends that you check your pull weight prior to use to ensure it is set at an appropriate level. See TriggerTech Bolt Action Pull Weight Guide. To ensure safety, never chamber a round until the rifle is safely pointed on a target and you are ready to fire.

Pull weight adjustment warning (continued)

유지관리&청소

Your TriggerTech trigger is designed to operate maintenance and lubricant-free. It is recommended that you minimize the amount of oil and gun cleaning products that get in contact with the trigger. If you believe your trigger is not working properly due to contamination, we recommend you take to following steps:

1. 총기에 탄약이 들어 있지 않은지 확인하세요.
2. Cycle the action, dry fire the rifle repeatedly. If necessary, try holding the rifle in different orientations while doing this.
3. If step 2 is unsuccessful, remove your TriggerTech trigger from the action and you can try to clean with compressed air and/or a grease-cutting agent that does not leave residue. We recommend lighter fluid, letting it dry, and blowing out the trigger with compressed air. Followthe TriggerTech Installation Instructions when reinstalling your trigger.
4. If step 3 is unsuccessful, we do NOT recommend opening your trigger housing and suggest you contact TriggerTech and arrange to have your trigger serviced. Note: breaking the “void if removed” will indicate that you have opened your trigger and may void the Limited Warranty. In the event you decide to ignore our recommendations and open your TriggerTech trigger, this is an image of the internal assembly:

Damaging your trigger

• We have gone to great lengths to design the most reliable and dependable triggers on the market and we are constantly striving to improve the safety and performance of all TriggerTech products. However, TriggerTech triggers are precision mechanical devices and they can be damaged. A damaged trigger could be or become
  위험한.

The following are conditions that may damage your trigger:

• Pierced Primer / Overpressure – the dynamic forces of the event may damage your trigger and prevent it from functioning safely.
• Untimed Action Damage – when you close the bolt with an untimed action you are hammering your trigger sear with the cocking piece. This can cause accelerated and unusual wear on your trigger and cocking piece. Excessive wear caused by an untimed action may cause your firearm to become unsafe as you can damage and /or break the cocking piece and/or trigger components. This is especially true with aggressive or repetitive dry cycling of your action. Cycling an untimed action without ammunition is more severe from a wear perspective than cycling with ammunition as moving ammunition will slow the bolt. TriggerTech recommends that you ensure your action is properly timed prior to use.
• Damaging your trigger when installing trigger pins during install – if you do not follow Step 4, you may damage the trigger by attempting to hammer a trigger pin through a trigger pin hole that is not aligned with the action mounting hole. Damage severity can range from cosmetic damage to the housing to catastrophic

Damaging your trigger (continued)

• damage where the trigger will no longer be able to be mounted to the action or function safely. It is possible to cause the trigger to fall out of factory alignment and in this case may cause degradation of the trigger’s safety and/or performance. Shooters are reminded:
• Your trigger’s pull weight should not change suddenly. A sudden change in pull weight is a sign that something is not right, and your arm may not be safe. Stop using your trigger and contact TriggerTech Support (support@triggertech.com) 1-888-795-1485.
• Your trigger’s pull weight may change slightly over the trigger’s lifetime as the parts wear in. Any change should be gradual and not in excess of 6oz or 15% (whichever is less). A change in excess of this is a sign that something is not right, and your firearm may not be safe. Stop using your trigger and contact TriggerTech Support (support@triggertech.com) 1-888-795-1485.
• If you notice a change in your trigger’s ability to hold the ring pin when closing the bolt do not try to overcome this by increasing pull weight. Stop using the trigger immediately and contact TriggerTech Support (support@triggertech.com) 1-888-795-1485.
• Always safety check your equipment prior to use and using live ammunition.
• Always follow the NRA Gun Safety Rules.  (https://gunsafetyrules.nra.org)

CONTANT INFORMATION

TriggerTech.com/pages/faq
1-888-795-1485
지원@TriggerTech.com
www.TriggerTech.com

자주 묻는 질문