JONSBO TK-5 Computer Case User Manual

JONSBO TK-5 컴퓨터 케이스

제품 사양

• Dimension: 474mm (D) x245mm (W) x539mm (H)
• Material: SGCC 1.0mm. plastic. Glass 4mm
• Drive Bay: 3.5 HDDx4 or 3.5 HDD×2,2.5 SSD×2 or 3.5 HDDx3,2.5 SSDx1
• Motherboard: ITX. M-ATX. ATX. M-ATX back plug. ATX back plug
• PCI 확장 슬롯: 7
• Front I/0 Port: USB3.0×2. MIC & SPK×1. Type-Cx1
• PSU Support: ATX≤220mm
• Max. CPU Cooler Height: ≤180mm
• Max. Display Card Length: ≤460mm
• Fan: Top: 120mm*3 or 140mm*3 or 360 AlO (optional)
• Bottom: 120mm*3 or 140mm*3 (optional) Side: 120mm*3 (optional)Rear: 120mm*1 (optional)
• Weight: Standard version 10.72kg (net weight)

부품 목록

커넥터 다이어그램은 라인 순서 관계만 표시합니다. 기능은 실제 제품을 참조하세요.

설치

Remove the upper plate

• First loosen the thumb screws and push in the direction of the arrow to remove the upper plate.

Remove the glass side panel

1. Remove the 3 screws that secure the glass.
2. Lift in the direction of the arrow to remove the glass side panel.

오른쪽 측면 패널을 제거하세요

Push outwards in the direction of the arrow to remove the right side panel.

Remove the right lower trim panel

Lift in the direction of the arrow to remove the right lower trim panel.

마더 보드 설치

Place the motherboard in the viewing installation area and fix it with screws.

그래픽 카드 설치

1. Remove the PCI card strip and PCl cover.
2. 그래픽 카드를 마더보드 슬롯에 삽입하고 나사로 고정합니다.

전원 공급 장치 설치

Place the power supply into the installation area and lock it with screws.

3.5 HDD 설치

1. Remove the hard drive bracket from the bottom of the chassis and lock the 3.5 HDD on the hard drive bracket.
2. The assembled hard disk bracket is screwed onto the chassis from the bottom of the chassis.

SSD Hard Drive Installation

1. The SSD hard drive is assembled with screws and washers.
2. Remove the hard drive bracket from the bottom of the chassis, place the assembled SSD into the corresponding hole, and push it forward into the card slot.
3. The assembled SSD hard drive bracket is locked to the chassis with screws from the bottom of the chassis.

냉각 시스템

Install a fan in the middle partition

1. Remove the screws that fix the middle partition and remove the middle partition.
2. Fix the fan to the middle partition with screws and then install it back into the chassis.

Top water cooling installation

1. Lock the fan on the water cooling radiator.
2. The water cooling radiator is fixed on the top cover of the chassis.

설치 완료

1. Install the right lower trim panel in the direction indicated by the arrow.
2. Install the right side panel in the direction indicated by the arrow.
3. Install the glass from top to bottom and tighten the screws at the top.
4. Push the upper plate in the direction of the arrow and tighten the screws.

동관시보시통산업유한회사
No.5, Xinglong Lu, Sanzhong Village, Qingxi Town, Dongguan City, Guangdong Province, 523651, China © 2023 Dongguan Sibositong Industrial Co., Ltd. All rights reserved. Specifications are subject to change without prior notice. Some trademarks may be claimed as the property of others.