이글루 제빙기 매뉴얼
이글루 제빙기 매뉴얼
1. 투명 창으로 커버
2. 제빙기 및 푸셔
3. 물통 (표시되지 않음)
4. 제어판
5. 배수 캡 : 얼음물 배 수용 (본체 전면 버튼)
6. 압축기 냉각 팬 (공기 흐름을 막지 마십시오)
7. 얼음 삽
8. 얼음 바구니
제어판 : 사용하기 쉬움, LED 표시등이있는 버튼 기능
A. 전원 켜짐 LED 표시 등
B. 전원 ON / OFF 버튼
C. 아이스 큐브 사이즈 선택 버튼
D. 선택한 얼음 크기 LED 표시 등 표시 : 작은 얼음, 큰 얼음
만들 큐브
E.“ADD WATER”(물통에 물이 없다는 경고), 물을 추가해야 함 F.“ICE FULL”LED 표시 등
작동 지침
이 휴대용 제빙기는 쉽고 편리한 제빙을위한 첨단 마이크로 컴퓨터와 함께 전자동 제어 시스템을 사용합니다. 얼음을 만드는 것은 간단하고 빠릅니다. 물을 넣고 콘센트에 꽂은 다음 ON 버튼을 누르기 만하면됩니다. 버튼 터치로 두 개의 각 얼음 크기 중 하나를 선택할 수 있습니다. 장치를 처음 켜거나 제빙주기 동안 압축기는 전원이 공급되는 동안 3 분 동안 유휴 상태를 유지합니다.
저장통이 비었을 때 물을 채우고 저장 바구니가 가득 차면 얼음을 제거하라는 경고 표시기가 있습니다. 제빙기는 또한 우발적 인 손상을 제한 할 수있는 보호 장치가 내장되어있어 필요할 때 자동으로 시스템을 종료합니다.
작동 전 지침
주의 깊게 읽으십시오.
1. 제빙기 캐비닛의 경사각은 운송 또는 사용 중에 45 °를 초과하지 않아야합니다. 제빙기를 거꾸로 돌리지 마십시오. 그럴 경우 압축기 또는 냉장 시스템이 제대로 작동하지 않을 수 있습니다. 제빙기를 이동하거나 운반 할 때 압축기의 유체가 가라 앉을 때까지 기다리십시오. 제빙기를 처음 사용하기 전에 기기가 수평을 이루고 제자리에 놓인 후 2 시간을 기다리십시오.
2. 오작동을 방지하기 위해 제빙기가 평평하고 안정된 테이블이나 플랫폼 위에 있는지 확인하십시오.
3. 기계는 오븐, 히터 및 부식성 가스와 같은 열원에서 멀리 떨어진 건조하고 평평한 표면에 충분히 환기가되어야합니다.
적절한 환기를 위해 제빙기의 모든면에 8 인치 간격을 두십시오.
4. 물통에 뜨거운 물을 채우지 마십시오. 제빙기가 손상 될 수 있습니다. 물통에 상온 이하의 물을 채우는 것이 가장 좋습니다.
작동 지침
1. 상단 커버를 열고 얼음 저장 바구니를 꺼내고 물통에 음료수 (수돗물, 정수 또는 병에 담은 물) 2.3 쿼트의 물을 레벨 표시까지 채우고 얼음 저장 바구니를 교체합니다.
수위가 수위 표시 또는
얼음 저장 바구니의 바닥. 상단 덮개를 닫습니다.
참고 : 작동 과정에서 물통의 수위가 너무 낮아지면 기계가 자동으로 작동을 중지하고 LED에 "물 추가"표시등이 표시됩니다.
2. 장치를 접지 된 콘센트에 꽂습니다. 제어판의 ON / OFF 버튼을 눌러 기기를 켭니다.
3. S 또는 L 얼음 선택 버튼을 눌러 원하는 얼음 크기를 선택합니다.
S = 작은 얼음 조각 (약 7 분)
L = 큰 얼음 조각 (약 12 분)
제빙기는 곧 얼음을 만들기 시작합니다. 9 개의 얼음 조각의 다음주기가 완료됩니다 (수온, 주변 실내 온도 및 선택한 얼음 조각 크기 기준).
참고 : 작동을 중지하려면 ON / OFF 버튼을 누르십시오.
운영 프로세스
1. 물은 저수조에서 물통으로 펌핑되며 최대 1 분 정도 소요됩니다.
2. 증발기 봉을 물통에 담그면 제빙 사이클이 시작됩니다. 압축기가 작동하는 소리를들을 수 있습니다.
3. 선택한 크기에 따라 각 제빙주기마다 약 5-13 분 정도 소요됩니다. 크기가 클수록 얼음을 만드는 데 더 많은 시간이 필요합니다. 사이클이 끝나면 물통이 앞으로 기울어지고 남은 물은 물 저장 탱크로 다시 흘러 들어갑니다. 증발기 봉은 얼음을 방출합니다.
참고 : 실내 주변 온도가 60 ° F 미만이면 얼음 조각이 서로 융합되지 않도록 작은 얼음 조각 크기를 권장합니다.
4. 약 60 초 후 물통이 뒤로 기울어지고 얼음 푸셔가 얼음을 얼음 저장 바구니로 밀어 넣습니다. 워터 박스가 원래 위치로 돌아간 후 다음 제빙 사이클이 시작됩니다.
5. 얼음의 최대 용량이 수집되고 얼음이 온도 센서에 도달하면 제빙기가 자동으로 작동을 중지합니다. "ICE FULL"LED 표시등이 켜집니다.
얼음이 더 필요하면 얼음 저장 바구니에서 얼음을 제거하십시오. 그런 다음 바스켓을 기계에 다시 끼 우고 바스켓이 원래 위치로 돌아 왔는지 확인합니다. 참고 : 바스켓을 교체 할 때 온도 센서가 바스켓 위에 있는지 확인하여 기계가 제대로 작동하는지 확인하십시오.
6. 얼음을 계속 만들려면 저수 탱크에 물이 있는지 확인하십시오. 물 저장 탱크에 물이 없으면 물통에 물이 펌핑되지 않고 작동이 중지됩니다. “Add Water”LED 디스플레이가 켜집니다. “OFF”버튼을 누르십시오. 물 저장 탱크에 물을 채운 다음 제빙기가 다시 작동하기 위해“ON”버튼을 누르십시오. 압축기 내부의 냉매가 적어도 3 분 전에 침전되도록하십시오.
다시 시작합니다.
7. 물 부족 등의 사유로 압축기가 정지한 경우tage, 얼음이 너무 많거나 전원이 꺼진 경우 등, 즉시 기기를 다시 시작하지 마십시오. 기계를 다시 시작하기 전에 최소 3분을 기다리십시오.
청소 및 유지 관리
제빙기를 사용하기 전에 제빙기를 철저히 청소하는 것이 좋습니다. 제빙기를 정기적으로 청소하십시오.
1. 청소할 때는 전원이 꺼져 있고 콘센트에서 플러그가 뽑혀 있는지 확인하십시오. 콘센트에서 장치를 꽂거나 뽑을 때는 플러그를 직접 당기십시오. 전원 코드를 당기지 마십시오.
2. 얼음 저장 바구니를 제거합니다.
3. 장치에서 남은 물을 배출합니다. 캡을 제거한 다음
주둥이에서 고무 플러그. 다시 조립할 때
고무 플러그를 먼저 스파우트에 삽입 한 다음
모자. 그렇지 않으면 제빙기가 누출됩니다.
4. 미지근한 물에 희석 한 중성 세제를 사용하여 부드러운
수건이나 스폰지. 솔벤트, 세제 및 연마제는 절대로 청소에 사용해서는 안됩니다.
5. 얼음 저장 바구니, 물통, 물통, 얼음 푸셔 및 증발기 막대와 같은 내부 부품을 닦습니다.
6. 제빙기 외부는 중성 세제 용액, 따뜻한 물, 부드러운 천으로 정기적으로 청소해야합니다.
7. 부드러운 천으로 내부와 외부를 말립니다.
8. 장치를 청소 한 후 얼음 만들기를 시작하려면 깨끗한 물을 물통에 붓고 작동 지침에 따라 수평선까지 채우십시오. 제빙기를 기울이거나 옆으로 눕 히지 마십시오. 그렇지 않으면 압축기 냉각수가 가라 앉을 때까지 10 시간을 기다려야합니다.
9. 얼음 조각의 청결을 보장하기 위해 물 저장 탱크의 물은 24 시간마다 교체해야합니다.
10. 커피 머신을 사용하지 않거나 장기간 사용하지 않을 경우 배수 캡을 풀고 장치 뒤의 고무 플러그를 제거하여 물통에 남아있는 물을 완전히 비 웁니다. (위의 4 번 지침을 따르십시오.)
자주 묻는 질문
전원 표시등은 플러그를 꽂을 때만 켜집니다. 일반적으로 얼음 바구니가 가득 차서 얼음이 막혔을 때 표시등이 깜박입니다. 얼음 양동이를 비우고 표시등을 누르면 생산이 재개됩니다.
텍사스
배수 및 닦기
저수지가 비어 있습니다. 물을 추가합니다.
수위가 너무 높습니다. 약간의 물을 제거하십시오.
오작동으로 인해 제빙기가 자동으로 꺼졌습니다. 전원을 끄고 10분 동안 기다렸다가 다시 켜십시오. 문제가 지속되면 대리점이나 Igloo 고객 서비스 센터에 도움을 요청하세요.
뚜껑을 열면(그리고 열 수 있는 공간) 19인치의 헤드룸이 필요합니다.
우리는 그 문제가 없었습니다. 우리는 증류수만 사용합니다. 우리는 우리의 제빙기를 사랑했습니다. 플러그를 꽉 조여야 합니다
선과 단어 채우기 선으로 표시됩니다.
아주 최소한의. 얼음이 떨어지고 양동이로 뒤집히는 소리가 들릴 것입니다. 그러나 얼음을 만드는 동안 소음이 거의 없습니다.
2 amps
이것은 물 연결이 필요합니까?
아니요 물 연결이 필요하지 않지만 코드가 뜨거워져 불이 붙을 수 있다는 점에 유의하십시오! 그들은 내 것에 대해 아무 것도하지 않을 것이고 나는 2 개월 동안 내 것을 가지고있었습니다! 정직한 기업을 위한 것!
약 31일 동안 고장나서 작동을 멈춘 종류..
전기 미국 표준 콘센트에 꽂습니다!
Igloo는 텍사스주 케이티에 본사를 두고 제조됩니다.
투명한 창 안에는 각얼음을 담는 바구니가 있어요! 스쿱과 함께 제공되며 6분마다 한 방울의 얼음이 만들어집니다!
내 것은 여름 더위에 계속 켜져 있으며 가득 차면 얼음 상자에 냉장고로 옮깁니다!
이 제품을 만드는 회사는 "브랜드" Igloo의 라이센스 사용자일 뿐입니다. 이것은 나의 두 번째 유닛이고, 실제로 Igloo에서 만든 것으로 생각되는 내 원래 유닛과 매우 유사해 보였습니다. 이 장치에 대한 필요 사항이 무엇이든 Igloo에 직접 연락하려고 합니다.
수위는 정확해야 하며 품목은 수평이어야 하며, 제빙기를 껐다가 다시 켜서 원하는 종류의 얼음을 선택해야 합니다. 그래도 물이 나오지 않으면 펌프가 좋지 않거나 막혔을 수 있습니다.
측정값은 제품 설명에 나와 있습니다. 그러나 너비는 약 10인치, 깊이는 12인치, 높이는 14인치입니다. 뒤쪽과 오른쪽의 공기 순환이 필요합니다.
모든 아이스 큐브는 다양한 크기로 제공됩니다. 종종 기계가 시동된 이후 첫 번째 사이클에서 얼음이 더 작습니다. 그러나 일단 얼음이 3번째 주기에 이르면, 종종 그것은 더 커집니다. 크기는 기계를 작동하는 시간에 따라 다릅니다. 친애하는; 고객 관리 담당자
90일.
그것이 얼음을 떨어뜨릴 때까지 침묵하고 그것은 정말로 많지 않습니다!
그것은 빛을 활성화하는 센서가 있으며 가득 차면 더 이상 얼음을 만들지 않습니다. 얼음을 만들지 않을 때는 조용하다는 것을 알게 될 것입니다. 멋진 기계입니다.
제빙기
아니요, 청소가 필요하지만 제 생각에는 최소한의 것입니다.
주문한 제빙기를 받지 못한 경우 "내 주문"으로 이동한 다음 "패키지 추적"을 클릭하면 예상 배송 날짜가 표시됩니다... 그렇지 않은 경우 "연락처"로 이동하십시오.. 고객 서비스.. 고객 서비스에 전화하십시오. 도움이 될 것입니다.
동영상
참고문헌
- 사용자 설명서manual.tools
제빙기가 제대로 작동하지 않으면 어떻게해야합니까?
What should I do if my Igloo ice maker is not working properly?
If your Igloo ice maker is not working properly, try the following troubleshooting steps based on the manual:
If the ice maker still does not produce ice after these steps, it may have a pump malfunction or a clog. Contact Igloo customer service for further assistance.
For more details, you can view 그만큼 full Igloo Ice Maker Manual here.
Note: There is some uncertainty regarding the specific model, as the manual covers general portable Igloo ice maker functions.
Read the full Q&A page
바구니에 얼음이 가득 차도 제빙기가 꺼지지 않습니다. 얼음을 바구니에 떨어뜨리는 가드를 깨뜨렸습니다.
What should I do if my Igloo ice maker is not working properly?
바구니에 얼음이 가득 차도 제빙기가 꺼지지 않습니다. 얼음을 바구니에 떨어뜨리는 가드를 깨뜨렸습니다.
어떻게 새 바구니를 얻습니까?
How can I get a replacement ice basket for my Igloo ice maker?
To obtain a replacement ice basket for your Igloo ice maker, you should contact the manufacturer or an authorized dealer directly. The manual suggests that the product may be manufactured by a licensee of the Igloo brand. You can try the following contact methods:
Please note that the standard warranty for these units is typically 90 days. If your unit is outside of this period, you may need to purchase the basket as a separate replacement part.
Read the full Q&A page
제 제빙기가 더 이상 얼음을 만들지 않습니다. 물 탱크가 가득 찼습니다. 물이 제대로 흐르도록하는 데 문제가있는 것 같습니다. 또한 물을 얻으려고 할 때 큰 소리가납니다. 내 옵션은 무엇입니까? 나는 정말로 내 기계를 사랑한다
기계를 청소했나요? 내부 표면이나 막대에 쌓인 것이 있나요? 한 번도 청소한 적이 없거나 수돗물을 사용하고 있다면 막대나 튜브가 막힌 것이 있습니다. 지침에 따라 기계를 청소하고, 석회질 제거제를 구해서 넣어보세요. 그래도 안 된다면, 기기를 정비해야 합니다. 행운을 빕니다!
Igloo MDL # ICE108 용 압축기 냉각수 교체 팬은 어디서 구할 수 있습니까 ??
Where can I find a replacement compressor cooling fan for the Igloo ICE108 ice maker?
The Igloo ICE108 manual identifies the compressor cooling fan as a key component (Part #6), but it does not provide a direct link for purchasing replacement parts. To find a replacement fan, you can try the following steps:
메모: Always ensure the unit is unplugged before attempting any repairs or part replacements.
Read the full Q&A page
팬은 내부 컴퓨터 부품을 냉각하는 데 사용되는 것과 동일한 유형의 팬입니다.
Where can I find a replacement compressor cooling fan for the Igloo ICE108 ice maker?
팬은 내부 컴퓨터 부품을 냉각하는 데 사용되는 것과 동일한 유형의 팬입니다.
이 모든 걸해도 얼음이 안 나오면 어떡해 ???
What should I do if my Igloo ice maker still doesn't make ice after following the manual's instructions?
If your Igloo ice maker is not producing ice after following the initial setup, try these troubleshooting steps:
If the problem persists after these steps, the manual recommends contacting your dealer or Igloo customer service for further assistance.
Read the full Q&A page
I have a ICE 102ST. Power is on, I can select ice size, machine has distilled water. The top is going thru the motions to make ice and dump it-but the ice full light comes on and fan is not turning. No ice made or water used. Help!
What should I do if my Igloo ice maker still doesn't make ice after following the manual's instructions?
I have a ICE 102ST. Power is on, I can select ice size, machine has distilled water. The top is going thru the motions to make ice and dump it-but the ice full light comes on and fan is not turning. No ice made or water used. Help!
이글루의 제빙기가 소리를냅니다.
Why is my Igloo ice maker making a noise?
It is normal for your Igloo ice maker to make some sounds during operation. According to the manual, you can expect to hear the following:
The manual describes the overall noise level as "very minimal." However, if you hear abnormal or unusual noises beyond these standard operational sounds, the manual recommends consulting the manufacturer for further troubleshooting. Ensure the unit is level on a stable platform, as an uneven surface can sometimes cause increased vibration or noise.
If the sound is accompanied by flashing lights, it may indicate that the ice basket is full or that ice is stuck. Try emptying the basket and restarting the unit.
Read the full Q&A page
Igloo 모델 ICE108에 대한 설명서를 어디서 구할 수 있는지 아는 사람이 있나요? 부품을 어디서 살 수 있는지, 부품 이름을 알아야 합니다. 설명서를 잃어버렸거나 받지 못했습니다.
Where can I find the manual and a parts list for the Igloo ICE108 ice maker?
The manual for the Igloo Ice Maker (which covers common portable models like the ICE108) is available on this page. You can find the full text above or download the PDF version via the links provided in the post.
부품 목록:
구매를 위해asing specific replacement parts, it is recommended to contact Igloo customer service directly or visit their official web사이트에서
www.iglooicemakers.com. Many users also find replacement baskets and scoops through major online retailers by searching for the model number ICE108.메모: If your unit is under 90 days old, it may still be covered by the manufacturer's warranty.
Read the full Q&A page
제빙기의 물 튜브는
Where are the water tubes located in the Igloo ice maker?
The water tubes in the Igloo ice maker are internal components that facilitate the movement of water from the reservoir to the ice-making mechanism. According to the manual and operating process:
While the specific "tubes" are not externally visible or listed as a user-serviceable part in the basic diagram, they connect the 물 저장고 에게 물 상자. If you are experiencing issues with water flow, ensure the unit is level and the water pump is not clogged. For cleaning, you can wipe down the internal parts including the water reservoir and water box with a mild detergent and warm water.
If you need to drain the unit, the water drain cap and rubber plug are located at the bottom or back of the unit, depending on your specific model.
Always ensure the unit is unplugged before attempting to inspect any internal components.
View the full Igloo Ice Maker Manual here for more details on parts and maintenance.
Read the full Q&A page
메이커보다 수익성이 높은 이글루의 대체 아이스 바구니는 어디에서 구입할 수 있나요?
Where can I purchase a replacement ice basket for my Igloo ice maker?
To purchase a replacement ice basket for your Igloo ice maker, you should first contact Igloo customer service directly. While the manual mentions contacting your dealer or Igloo customer service for assistance, it is important to note that many Igloo-branded ice makers are manufactured under license by other companies. You can visit www.iglooicemaker.com for specific support related to these units.
Additionally, you may find compatible replacement baskets on major online retail platforms like Amazon or eBay by searching for your specific model number followed by "replacement ice basket." Ensure you verify the dimensions of the basket before purchasing to guarantee a proper fit.
If you are unsure of your model number, it is typically located on a sticker on the back or bottom of the unit.
Read the full Q&A page
내 이글루 제빙기 물을 넣고 가벼운 얼음이 꽉 찼다는 걸 보여줘 사실이 아니야 얼음이 아냐
Why is the 'Ice Full' light on when the basket is empty and no ice is being made?
If your Igloo ice maker is showing the 얼음 가득 light even though the basket is empty, it is likely a sensor issue. Here are the steps to troubleshoot this:
If the light continues to flash and the machine will not start, there may be an internal malfunction. In this case, it is recommended to contact Igloo customer service for further assistance.
Read the full Q&A page
내 IGLOO 제빙기에서 물이 이미 들어있을 때“물을 추가하십시오”라고 말합니다. 그러면 아무것도하지 않습니다. 꺼! 플러그를 뽑으십시오. 기다림. 플러그를 꽂고 켜면 시작되고 표시등이 다시 켜집니다.
Why does my Igloo ice maker say 'add water' when the reservoir is already full?
If your Igloo ice maker displays the "ADD WATER" light despite having water in the reservoir, it may be due to a sensor or pump issue. Here are the recommended troubleshooting steps:
If the problem persists after these steps, the water pump may need to be replaced, or you should contact Igloo customer service for further assistance.
Read the full Q&A page
저도 똑같은 일을하고 있습니다 !!
So is mine
이글루 제빙기를 재설정했는데 다시 작동합니다. 물이 꽉 찼지만 계속 물을 넣으십시오.
제빙기 플러그를 뽑습니다
뚜껑을 열고 중앙에있는 얼음 국자를 잡고 멈출 때까지 뒤로 미십시오.
멈출 때까지 앞으로 당긴 다음 반복합니다. 이렇게 하면 재설정됩니다.
플러그를 꽂고 물을 넣은 다음 전원을 켜고 작은 얼음으로 설정하여 테스트해 보세요.
행운을 빌어요
제빙기 플러그를 뽑습니다
뚜껑을 열고 중앙에있는 얼음 국자를 잡고 멈출 때까지 뒤로 미십시오.
멈출 때까지 앞으로 당긴 다음 반복합니다. 이렇게 하면 재설정됩니다.
플러그를 꽂고 물을 넣은 다음 전원을 켜고 작은 얼음으로 설정하여 테스트해 보세요.
행운을 빌어요
How do I reset my Igloo ice maker when it says 'add water' even though it is full?
If your Igloo ice maker is displaying an "Add Water" alert while the reservoir is full, you can attempt a manual reset of the internal mechanism. Follow these steps:
If the "Add Water" light persists, ensure the unit is level and that the water pump is not clogged. If these steps do not resolve the issue, the pump may be malfunctioning and require professional service.
Note: Always allow the refrigerant to settle for at least 3 minutes before restarting the machine if it has been recently powered off.", "contextual_details_en": "Troubleshooting an Igloo ice maker that incorrectly displays an 'add water' alert despite having a full reservoir.", "answer_en": "
If your Igloo ice maker is displaying an 'Add Water' alert while the reservoir is full, you can attempt a manual reset of the internal mechanism. Follow these steps:
If the 'Add Water' light persists, ensure the unit is level and that the water pump is not clogged. If these steps do not resolve the issue, the pump may be malfunctioning and require professional service.
Note: Always allow the refrigerant to settle for at least 3 minutes before restarting the machine if it has been recently powered off.
Read the full Q&A page
"밀다"란 무슨 뜻입니까? 정확히 무엇을 뒤로 밀고 앞으로 당기고 있습니까?
Unfortunately this didn’t work with mine
How do I reset my Igloo ice maker when it says 'add water' even though it is full?
Unfortunately this didn't work with mine
물통에 건크가있어 어떻게 청소를 할 수 있습니까? 나오나요?
How can I clean the water box in my Igloo ice maker? Does it come out?
The water box in the Igloo ice maker is a tilting component that moves during the ice-making cycle. While the manual does not explicitly state that the water box is removable for cleaning, it provides instructions for cleaning it in place:
If the gunk is difficult to reach, you may need to wait for the water box to tilt forward (which happens naturally after an ice cycle) to access more of its surface area. Avoid using solvents or abrasive cleaners as they may damage the unit.
If you suspect the pump or lines are clogged with residue, ensure you are replacing the water every 24 hours to maintain cleanliness.
Note: If the unit is still under warranty (typically 90 days), avoid forceful removal of parts that are not designed to be detached, as this may void your warranty.
Read the full Q&A page
제 제빙기가 얼음을 만들지 않습니다. 재설정하는 방법을 알 수 없습니다. 방금 XNUMX 월에 사용하기 시작했는데 이미 작동을 멈췄습니다.
How do I reset my Igloo ice maker and troubleshoot why it is not making ice?
If your Igloo ice maker has stopped making ice, you can perform a manual reset by following these steps:
If the unit still fails to produce ice after a reset, check if the evaporator rods are getting cold or if the water pump is functioning. If the problem persists, it may indicate a mechanical failure or a refrigerant issue, and you should contact customer service.
", "contextual_details_en": "Troubleshooting an Igloo ice maker that has stopped producing ice and seeking instructions on how to perform a reset.
Read the full Q&A page
대체 아이스 바구니는 어디서 구할 수 있나요?
Where can I purchase a replacement ice basket for my Igloo ice maker?
To obtain a replacement ice basket for your Igloo ice maker, you should first contact Igloo customer service directly. While the manual mentions that some units may be manufactured by licensees, reaching out to the brand owner is the best starting point for genuine parts. You can also search for the specific model number of your unit on major online retailers or specialized appliance part websites, as these baskets are often standard sizes for portable units.
If you are unsure of your model number, it is typically located on a sticker on the back or bottom of the machine. When searching for a replacement, ensure the dimensions match your current unit to maintain proper operation of the temperature sensor, which sits above the basket to detect when it is full.
Read the full Q&A page
대체 아이스 바구니는 어디서 구할 수 있나요?
Where can I purchase a replacement ice basket for my Igloo ice maker?
To obtain a replacement ice basket for your Igloo ice maker, you should first contact the manufacturer or the retailer where the unit was purchased. According to the manual, you can reach out to Igloo customer service for assistance with parts and malfunctions.
If the unit is still under its 90일 보증, you may be eligible for a replacement through their support channels. You can also search for the specific model number on the official Igloo Ice Makers web대지 or check major online retailers for compatible replacement baskets.
Read the full Q&A page
이글루 ice102c를위한 투명한 창이 필요합니다. 어디서 찾을 수 있나요
Where can I find a replacement transparent window for the Igloo ICE102C ice maker?
The Igloo ICE102C manual identifies the "Cover with transparent window" as part number 1. However, the manual does not provide a direct parts ordering list or specific SKU for individual components.
To find a replacement window, you can try the following steps:
Please note that the window is typically integrated into the top cover assembly, so you may need to replace the entire lid rather than just the transparent pane.
Read the full Q&A page
There is mold building up in the double pane in mine and I can’t find any instructions on how to clean it!
대체 얼음 바구니와 스쿱은 어디에서 구입할 수 있습니까?
Where can I purchase a replacement ice basket and scoop for my Igloo ice maker?
To purchase a replacement ice basket or scoop for your Igloo ice maker, you should first contact Igloo customer service directly. While the manual mentions these parts (items 7 and 8), it does not provide a direct ordering link. You can visit www.iglooicemaker.com for official support.
Additionally, many Igloo ice makers are manufactured under license by other companies like Curtis International. If you cannot find parts through Igloo, you may want to check with 커티스 인터내셔널 or search for your specific model number on major retail sites like Amazon or eBay, as these generic replacement baskets and scoops are often compatible across various portable ice maker brands.
Read the full Q&A page
대체 얼음 바구니는 어디에서 구입할 수 있습니까?
Where can I purchase a replacement ice basket for my Igloo ice maker?
To purchase a replacement ice basket for your Igloo ice maker, it is recommended to contact Igloo customer service directly. While the manual mentions that the product may be manufactured by a licensee, you can visit www.iglooicemaker.com for support and parts inquiries.
Additionally, you may find compatible replacement baskets through major online retailers like Amazon or eBay by searching for your specific model number. If you are unsure of your model number, it is typically located on a sticker on the back or bottom of the unit.
When contacting support or searching for parts, ensure you have the model details ready to confirm the basket will fit your specific machine.
Read the full Q&A page
내 제빙기 - Igloo ICE108 - 사망 - 배송비를 지불하고 싶다면 원하는 부품을 가질 수 있습니다. 연락하다 horsino@aol.com
How can I troubleshoot or repair my Igloo ICE108 ice maker if it has stopped working?
If your Igloo ICE108 ice maker has stopped working, you can try the following troubleshooting steps before considering it beyond repair:
If these steps do not resolve the issue, the manual suggests contacting your dealer or Igloo customer service for further assistance, as the unit may have a internal component failure such as a faulty compressor or control board.
메모: Manuals.plus is a platform for sharing product manuals and does not facilitate the exchange or purchase of used parts.
Read the full Q&A page
우리의 제빙기는 하루 종일 얼음을 만들 것입니다. 하지만 밤이 되면. 멈춘다. 그런 다음 아침 시간에는 다시 얼음이 있습니다. 이상해 다른 밤 시간. 잘 작동합니다. 왜 친절하게 이러는거야??
Why does my Igloo ice maker stop making ice at night but work during the day?
Based on the Igloo Ice Maker manual, there are a few reasons why your unit might stop at night and resume in the morning:
If the unit is not full of ice and has plenty of water, try resetting it by turning the power off for 10 minutes and then back on. If the problem persists, it may be a sensor malfunction related to the change in light or temperature at night.
Read the full Q&A page
내 것을 켜면 시작되는 것처럼 작동한 다음 종료되고 물을 추가하라고 말합니다. 플러그를 뽑아 보았지만 아무 것도 도움이되지 않는 것 같습니다.
Why does my Igloo ice maker shut off and display 'Add Water' immediately after starting, even when it has water?
If your Igloo ice maker is shutting off and displaying the "Add Water" light despite having water in the reservoir, there are several potential causes and solutions:
If the problem persists after cleaning and ensuring the unit is level, the water pump may be faulty, and you should contact Igloo customer service for further assistance.
Note: Always ensure the rubber drain plug is tightly inserted before use to prevent leaks that could lead to a low water condition.
For more detailed instructions, you can refer to the 이글루 제빙기 매뉴얼.
Troubleshooting Summary:
동영상 가이드 :
Igloo Ice Maker Instruction Video
Read the full Q&A page
I have the exact same problem. I haven’t used in in about 4 months. Brought it out wanting to make ice. I turn it on and it sounds like its starting the process and then shuts off and ALL the lights on the panel are on
제 제빙기가 딸깍 소리를 내며 큐브를 버리려고 힘을 씁니다. 또한 내부 저수지는 펑키합니다. 제거하려면 어떻게 해야 합니까?
How do I clean my Igloo ice maker and troubleshoot clicking noises?
To address the clicking noise and cleaning of your Igloo ice maker, follow these steps based on the manual:
Read the full Q&A page
Igloo Model ice102st의 교체용 얼음 바구니는 어디에서 구입할 수 있나요?
Where can I purchase a replacement ice basket for the Igloo ICE102ST ice maker?
To purchase a replacement ice basket for your Igloo ICE102ST, you have several options:
When searching, ensure the dimensions match your current basket to guarantee a proper fit, as the ICE102ST is a compact portable unit.
Read the full Q&A page
Where can I purchase a replacement ice basket/bucket for my igloo ice maker model: 117-ss
Where can I purchase a replacement ice basket for my Igloo ice maker model 117-ss?
While the provided manual does not list a direct source for purchasing replacement parts, the best approach is to contact the manufacturer or their authorized parts distributor.
다음은 몇 가지 제안입니다.
When you contact them, be sure to have your specific model number (117-ss) available to ensure you get the correct part.
Read the full Q&A page
The machine has water, I learned it, it fills all well and then it turns off saying ice full ma, there is no ice … what did it do?
la máquina tiene agua, la aprendí , se llena todos bien y después se apaga diciendo ice full ma no está hielo… que ago?
la máquina tiene agua, la aprendí , se llena todos bien y después se apaga diciendo ice full ma no está hielo… que ago?
Why does my Igloo ice maker say 'Ice Full' when there is no ice?
If your Igloo ice maker indicates it is full when it is not, it is likely a sensor issue. Here are the steps to troubleshoot this problem:
If the 'ICE FULL' light continues to flash and the machine will not start, there may be a internal malfunction. In this case, it is recommended to contact Igloo customer service for further assistance.
Read the full Q&A page
Water box sticks in the empty position and must be manually helped to rotate and most often to dump the cubes
Why is the water box on my Igloo ice maker sticking and failing to rotate or dump ice cubes?
If the water box on your Igloo ice maker is sticking or failing to rotate, it often indicates a mechanical obstruction or a need for cleaning. Here are several steps to troubleshoot the issue:
Note: Always ensure the unit has at least 8 inches of clearance on all sides for proper ventilation, as overheating can also lead to system malfunctions.
Source: Igloo Ice Maker Manual Operating Process and Cleaning sections.", "contextual_details_en": "Troubleshooting a mechanical issue where the water box sticks in the empty position and requires manual assistance to rotate and dump ice cubes.", "answer_en": "
If the water box on your Igloo ice maker is sticking or failing to rotate, it often indicates a mechanical obstruction or a need for cleaning. Here are several steps to troubleshoot the issue:
Note: Always ensure the unit has at least 8 inches of clearance on all sides for proper ventilation, as overheating can also lead to system malfunctions.
Source: Igloo Ice Maker Manual Operating Process and Cleaning sections.
Read the full Q&A page
Can I just leave it by plugged in after it makes a basket and it will keep made ice frozen for a couple of days? How long
Can I leave the Igloo ice maker plugged in after it finishes making ice, and will it keep the ice frozen for a few days?
No, the Igloo portable ice maker is not designed to keep ice frozen for several days. While it is an automatic machine that will stop when the basket is full (indicated by the "ICE FULL" light), it is not a freezer.
If you leave it plugged in, it will continue to cycle through making ice and recycling melted water, but it will not maintain a frozen batch for days at a time.
Read the full Q&A page
My water is full and it makes a handful of ice cubes and tells me add water and quits working why?
Why does my ice maker stop and say 'Add Water' when the reservoir is full?
If your Igloo Ice Maker is reporting a water shortage despite being full, there are several troubleshooting steps you can take:
If these steps do not resolve the issue, the internal pump or water sensor may be defective, and you should contact Igloo customer service for further assistance.
메모: Always allow the refrigerant to settle for at least 3 minutes before restarting the machine after it has stopped due to an error.
Source: Igloo Ice Maker Operating Instructions and FAQ.
Read the full Q&A page
Fill it up, put water in it, it makes a noise shuts off, but the fill water is still on, what do I do?
Why does my Igloo ice maker shut off with a noise while the water reservoir is still full?
It sounds like your ice maker may be encountering a sensor or mechanical issue. Here are several steps to troubleshoot this behavior:
If the 'Add Water' light is flashing despite the reservoir being full, the pump may be failing to move water into the internal water box. If these steps do not resolve the issue, you may need to contact Igloo customer service as the internal pump or sensor may require professional repair.
Read the full Q&A page
My ice maker is probably having a water pump problem. I makes a really awful noise when the water is being pumped up to make the ice. I don’t think it is a year old yet.
Why is my Igloo ice maker making a loud noise when pumping water?
If your Igloo ice maker is making an unusual or loud noise during the water pumping phase, it may be due to a few common factors:
Since your unit is less than a year old, it may still be under warranty. The manual suggests contacting your dealer or Igloo customer service if malfunctions persist. You can also try turning the unit off, waiting 10 minutes, and restarting it to see if the noise clears.
Read the full Q&A page
NEED STARTER CAPS FOR COMPRESSOR WHERE CAN I BUY THEM
Where can I buy replacement starter capacitors for an Igloo ice maker compressor?
The Igloo Ice Maker manual does not list specific internal electrical components like starter capacitors as user-replaceable parts. For specialized components such as compressor capacitors, it is recommended to contact the manufacturer or an authorized service center.
You can try the following resources for replacement parts:
메모: Opening the unit to replace internal electrical components may void your warranty and should only be performed by individuals comfortable with electrical repairs. Always ensure the unit is unplugged before attempting any maintenance.
Read the full Q&A page
My light is saying full but it not. How do I fix that?
Why is the 'Ice Full' light on when the basket is not full?
If your Igloo Ice Maker indicates it is full when it is not, it is likely a sensor issue. Here are the steps to troubleshoot and fix this:
If the light continues to flash or stay on after these steps, the sensor or the internal microcomputer may be malfunctioning, and you should contact customer service.
Based on the manual for the Igloo Ice Maker, if the "ICE FULL" light is on but the basket is not actually full, it is likely a sensor issue. Here are the troubleshooting steps to resolve this:
If these steps do not fix the issue, the sensor may be faulty or dirty. You can try gently wiping the sensor area with a soft cloth.
Read the full Q&A page
What type of refrigerant does this unit take, and where is it added?
Igloo ICEBNH26SS
Igloo ICEBNH26SS
What type of refrigerant does the Igloo ICEBNH26SS ice maker use and where is it added?
The Igloo ICEBNH26SS ice maker typically uses R134a or R600a refrigerant, though you should check the specific rating label on the back or bottom of your unit to confirm the exact type and amount required for your model.
Important Note on Adding Refrigerant: Portable ice makers are sealed systems. Refrigerant is not a consumable like water; it should never need to be "added" or topped off under normal operation. If the unit is not cooling, it likely has a leak or a compressor failure. Adding refrigerant requires specialized tools (such as a piercing valve and manifold gauges) and should only be performed by a certified HVAC technician. Attempting to add refrigerant yourself can be dangerous, may void your warranty, and could permanently damage the unit.
For general maintenance, ensure the unit has at least 8 inches of clearance on all sides for proper ventilation and that the compressor cooling fan is not blocked.
If you suspect a refrigerant issue, it is recommended to contact Igloo customer service or a professional repair technician.
For more details, you can refer to the 이글루 제빙기 매뉴얼.
Disclaimer: Handling refrigerants is regulated by law in many regions and requires professional certification.
Read the full Q&A page
I notice these comments haven’t been answered. They are going back to 2020. Can someone please respond. I’m having the issue with my igloo registering add water.
How do I fix the 'Add Water' error on my Igloo ice maker?
If your Igloo ice maker is displaying the "ADD WATER" alert even when there is water in the reservoir, follow these troubleshooting steps:
If the "Add Water" light persists after these steps, the water pump may be malfunctioning or the sensor may be faulty, and you should contact Igloo customer service for further assistance.
메모: Always wait at least 3 minutes before restarting the machine if it has been turned off to protect the compressor.
For more details, you can refer to the 이글루 제빙기 매뉴얼.
Disclosure: If your specific model differs from the standard portable unit, some steps may vary slightly.
Read the full Q&A page
Does igloo ice maker have to have an ice basket to function properly. If so, where can I get a New one ?? I lost original during our last move to another apartment.
Does the Igloo ice maker require an ice basket to function, and where can I buy a replacement?
Yes, the ice basket is necessary for the Igloo ice maker to function properly. The unit uses a temperature sensor located above the basket to detect when it is full. Without the basket, the ice will fall directly into the water reservoir, and the sensor may not correctly trigger the "ICE FULL" indicator, potentially causing the machine to malfunction or overflow.
To obtain a replacement ice basket, you can try the following:
When you get a new basket, ensure the temperature sensor is positioned above it so the machine can accurately detect when the ice reaches maximum capacity.
Technical:00:00:00.000 --> 00:00:04.160
In this video, I'm going to show you how to
use the Google Search Console URL 검사 도구
00:00:04.160 --> 00:00:08.160
당신의 것을 확인하려면 website is indexed on Google.
00:00:08.160 --> 00:00:11.760
This tool is great for checking if Google has crawled
00:00:11.760 --> 00:00:14.400
and indexed a specific page on your web대지.
00:00:14.400 --> 00:00:18.000
It's also great for troubleshooting why a page isn't appearing
00:00:18.000 --> 00:00:20.400
in search results and for requesting indexing
00:00:20.400 --> 00:00:23.040
for new or updated content.
00:00:23.040 --> 00:00:26.400
To get started, log in to your Google Search Console account
00:00:26.400 --> 00:00:29.280
and select the property you want to check.
00:00:29.280 --> 00:00:32.400
In the top search bar, enter the URL of the page
00:00:32.400 --> 00:00:35.280
you want to inspect and press enter.
00:00:35.280 --> 00:00:38.400
Google will then retrieve the data for that URL.
00:00:38.400 --> 00:00:41.280
If the page is indexed, you'll see a green checkmark
00:00:41.280 --> 00:00:44.160
next to "URL is on Google."
00:00:44.160 --> 00:00:47.280
If it's not indexed, you'll see a message saying
00:00:47.280 --> 00:00:50.400
"URL is not on Google."
00:00:50.400 --> 00:00:53.280
You can also see more detailed information about the page,
00:00:53.280 --> 00:00:56.400
such as when it was last crawled and if there are any errors.
00:00:56.400 --> 00:00:59.280
If the page isn't indexed, you can click on
00:00:59.280 --> 00:01:02.400
"Request Indexing" to ask Google to crawl it.
00:01:02.400 --> 00:01:05.280
This is a great way to get your new content indexed faster.
00:01:05.280 --> 00:01:08.400
And that's it! The Google Search Console URL 검사 도구
00:01:08.400 --> 00:01:11.280
is a powerful tool for any website owner.
00:01:11.280 --> 00:01:14.400
Use it to make sure your pages are being found by Google
00:01:14.400 --> 00:01:17.280
and to troubleshoot any indexing issues.|In this video, I'm going to show you how to use the Google Search Console URL Inspection tool to check if your website is indexed on Google. This tool is great for checking if Google has crawled and indexed a specific page on your website. It's also great for troubleshooting why a page isn't appearing in search results and for requesting indexing for new or updated content. To get started, log in to your Google Search Console account and select the property you want to check. In the top search bar, enter the URL of the page you want to inspect and press enter. Google will then retrieve the data for that URL. If the page is indexed, you'll see a green checkmark next to "URL is on Google." If it's not indexed, you'll see a message saying "URL is not on Google." You can also see more detailed information about the page, such as when it was last crawled and if there are any errors. If the page isn't indexed, you can click on "Request Indexing" to ask Google to crawl it. This is a great way to get your new content indexed faster. And that's it! The Google Search Console URL Inspection tool is a powerful tool for any website owner. Use it to make sure your pages are being found by Google and to troubleshoot any indexing issues.
Read the full Q&A page
Not enough water is being pumped to the ice maker to make proper sized ice bullets.
Why is my Igloo ice maker not pumping enough water to make full-sized ice bullets?
If your Igloo ice maker is not pumping enough water to produce proper-sized ice bullets, there are several potential causes and solutions to check:
If the pump continues to fail after cleaning and leveling, the pump itself may be defective and require professional service or replacement.
Note: Always wait at least 3 minutes before restarting the compressor if it has been shut off to allow the refrigerant to settle.", "contextual_details_en": "Troubleshooting an issue where insufficient water is being pumped into the ice-making tray, resulting in small or malformed ice bullets.
Read the full Q&A page
The plastic piece that rolls the ice cubes broke on one side. Where can I get the part?
La pieza plástica que rueda los hielos se partió de un lado. Donde puedo conseguir la pieza?
La pieza plástica que rueda los hielos se partió de un lado. Donde puedo conseguir la pieza?
Where can I find replacement parts for an Igloo ice maker, specifically the ice pusher?
If the plastic ice pusher (the piece that moves the ice cubes into the basket) is broken, you can try the following options for replacement parts:
If the part is not available, some users have had success with plastic epoxy for minor cracks, though a full replacement is recommended for structural breaks.
For further assistance, you can also check the 이글루 제빙기 매뉴얼 for specific contact details or troubleshooting tips.
Note: If your unit is less than 90 days old, it may still be under warranty.
Spanish Translation: Si la pieza de plástico está rota, puede buscar repuestos en Amazon o eBay buscando "Igloo ice maker pusher replacement". También puede contactar al servicio al cliente de Igloo con su número de modelo.
부인 성명: Manuals.plus is a repository for manuals and is not affiliated with the manufacturer.
Uncertainty: Specific part availability varies by model and region.
Context: The user is reporting a broken ice pusher on an Igloo ice maker.
Answered by Manuals.plus 지원하다.
Post title: Igloo Ice Maker Manual
Post permalink: https://manuals.plus/igloo/igloo-ice-maker-manual
Comment author: Thais Hernández.
Comment author URL: 없음
Raw comment: The plastic piece that rolls the ice cubes broke on one side. Where can I get the part? La pieza plástica que rueda los hielos se partió de un lado. Donde puedo conseguir la pieza?
Comment moderation context: current_status=0; original_status=0; previously_spam=no; is_reply=no
Gatekeeper product guess: Igloo Ice Maker
Gatekeeper model guess: unknown
Gatekeeper note: The user is asking for a replacement part for their ice maker.
Manuals.plus site context: Manuals.plus hosts public manuals, setup guides, troubleshooting help, /upload for public manual submissions, and /deep-search for PDF/manual discovery.
Post content fallback: Igloo Ice Maker Manual Igloo Ice Maker Manual PARTS, FUNCTIONS AND FEATURES https://youtu.be/VYTDtu9ao2c 1. Cover with transparent window2. Ice maker and pusher3. Water reservoir (Not shown)4. Control panel5. Water drain cap: For draining water from ice water (Front Button of Unit)6. Compressor cooling fan (Do not block air flow)7. Ice shovel8. Ice basket Control Panel: Easy to use, button function with LED indicators A. Power ON LED indicator lightB. Power ON/OFF buttonC. Ice cube SELECT SIZE buttonD. Selected ice size LED light indicator displaying: SMALL, and LARGE icecubes to makeE. "ADD WATER" (Alerts that there is no water in the water reservoir), must add water F. "ICE FULL" LED indicator OPERATING INSTRUCTIONS This portable icemaker uses a fully automatic control system, with an advanced microcomputer for easy and convenient ice making. Making ice is simple and fast. Just add water, plug into an outlet, and press the ON button. You can select one of the two ice cube sizes with the touch of a button. When first turning on the unit or during icemaking cycles, the compressor will stay idle for 3 minutes, while energizing. There are warning indicators that alert you to fill water when the reservoir is empty and to remove ice when the storage basket is full. The icemaker also has built-in safeguards that can limit accidental damage, automatically shutting down the system when necessary. Pre-Operating Instructions Please read carefully. 1. The incline angle of the icemaker cabinet should not exceed 45° during transportation or use. Do not turn the icemaker upside down. Doing so could cause the compressor or refrigerating system to operate incorrectly. When the icemaker is moved or transported, please allow time for the fluids in the compressor to settle. 제빙기를 처음 사용하기 전에 장치의 수평을 맞추고 올바른 위치에 놓은 후 2시간 정도 기다려 주십시오. 2. 오작동을 방지하기 위해 제빙기가 수평이고 안정적인 테이블이나 플랫폼에 있는지 확인하십시오. 3. 기계는 오븐, 히터, 부식성 가스와 같은 열원으로부터 멀리 떨어져 통풍이 잘 되는 건조하고 평평한 표면에 설치해야 합니다. 적절한 환기를 위해 제빙기의 모든면에 8 인치 간격을 두십시오. 4. Do not fill the water reservoir with hot water. This may damage the icemaker. 물통에는 실온 이하의 물을 채우는 것이 가장 좋습니다. Operating Instructions 1. Open the top cover, take out the ice storage basket and fill the water reservoir with drinkable (tap, purified or bottled) 2.3 quarts water to the level mark and replace the ice storage basket. Make sure that the water level does not reach above the level mark or thebottom of the ice storage basket. 상단 덮개를 닫습니다. Note: During the operation process, if the level of water in the water reservoir becomes too low, the machine will automatically stop operating and the "Add Water" indicator will display on the LED. 2. 장치를 접지된 콘센트에 꽂습니다. Push the ON / OFF button on the control panel to turn on the machine.3. S 또는 L 얼음 선택 버튼을 눌러 원하는 크기의 얼음을 선택하세요. S = Small ice cubes (Approx. 7 minutes)L = Large ice cubes (Approx. 12 minutes) The icemaker will start making ice soon after. The next cycle of 9 ice cubes is complete (based on water temperature, ambient room temperature and selected ice cube size). 참고 : 작동을 중지하려면 ON / OFF 버튼을 누르십시오. Operating Process 1. 물은 저수조에서 워터박스로 펌핑되는데, 최대 1분이 소요될 수 있습니다. 2. The icemaking cycle begins when the evaporator rods are dipped into the water box. You will hear the compressor working. 3. It will take approximately 5-13 minutes for each icemaking cycle, depending on the size selected. The larger the size, the more time is needed to make the ice. After the cycle is finished, the water box will tilt forward and the remaining water will flow back into the water storage tank. The evaporator rods will then release the ice cubes. Note: If the room ambient temperature is below 60° F, then small ice cube sizes are suggested to prevent ice cubes from fusing together. 4. Approximately 60 seconds later, the water box will tilt backwards and the ice pusher will push the ice into the ice storage basket. After the water box flips back to its original position, the next icemaking cycle will begin. 5. When the maximum capacity of ice cubes is collected and the ice reaches the temperature sensor, the icemaker will automatically stop operating. The “ICE FULL” LED indicator will light up. If more ice is needed, remove the ice from the ice storage basket; then replace the basket into the machine, making sure that the basket is placed back to its original position. Note: When replacing the basket, ensure that the temperature sensor is above the basket so that the machine operates properly. 6. To continue making ice, check that there is water in the water storage tank. If there is no water in the water storage tank, then no water will be pumped into the water box, and the operation will stop. The "Add Water" LED display will light up. “끄기” 버튼을 누르세요. Fill the water storage tank with water, and then press the “ON” button for the icemaker to begin operating again. Allow the refrigerant inside the compressor at least 3 minutes to settle beforerestarting. 7. tage, too much ice, power off, etc., do not restart the machine right away. Wait at least 3 minutes before restarting the machine. CLEANING AND MAINTENANCE Before using your icemaker, it is strongly recommended that you clean the icemaker thoroughly. Be sure to clean the icemaker regularly. 1. When cleaning, please make sure the power has been turned off and the plug is disconnected from the outlet. When plugging or unplugging the unit from the outlet, pull directly on the plug. 전원 코드를 잡아 당기지 마십시오. 2. 얼음 저장 바구니를 제거하세요. 3. Drain remaining water from unit. Remove the cap, then therubber plug from the spout. When assembling back together,the rubber plug must be inserted first into the spout, and thencapped. Otherwise, the icemaker will leak. 4. Use a mild detergent diluted in warm water and wipe with a softtowel or sponge. 세척 시 용제, 세제, 연마재를 절대 사용해서는 안 됩니다. 5. 얼음 저장 바구니, 물통, 물통, 얼음 푸셔, 증발기 막대 등 내부 부품을 닦아주세요. 6. 제빙기 외부는 중성세제와 따뜻한 물, 부드러운 천을 이용해 정기적으로 닦아주세요. 7. 부드러운 천으로 내부와 외부를 말리세요. 8. 장치를 청소한 후 얼음 만들기를 시작하려면 물통에 깨끗한 물을 붓고 작동 지침에 따라 수위선까지 물을 채우십시오. 제빙기를 기울이거나 옆으로 눕히지 마십시오. 그렇지 않으면 압축기 냉각수가 안정될 때까지 10시간을 기다려야 합니다. 9. 각얼음의 청결을 유지하기 위해 저수조의 물은 24시간마다 교체해야 합니다. 10. 머신을 사용하지 않거나 장기간 사용하지 않을 경우 배수 캡을 푼 다음, 머신 뒤의 고무 마개를 제거하여 물통에 남아 있는 물을 완전히 비우십시오. (Follow the instructions in number 4 above.) FAQS Is the power light suppose to be flashing when off? The power light is only on when plugged in. The light flashes when the ice is stuck usually because the ice basket is full. Empty the ice bucket and press the light and production should resume. 어디서 만들어? Texas Cleaning process Drain and wipe Why is there no water in the reservoir? 물통이 비어 있습니다. 물을 추가하세요. 저수지에 물이 있는 이유는 무엇입니까? 수위가 너무 높습니다. 약간의 물을 제거하십시오. 제빙기가 얼음을 만들지 않는 이유는 무엇입니까? The ice maker has shut off automatically because of a malfunction. Turn off the power, wait for 10 minutes, and turn on again. If the problem persists, contact your dealer or Igloo customer service for assistance. How tall is the unit when the lid is open? I only have a 16" clearance. 뚜껑을 열면(그리고 열 수 있는 공간) 19인치의 헤드룸이 필요합니다. Water runs out of hole on bottom back by plug in? First use water all over counter and floor. Drain plug tightly fitted. We have not had that issue. We only use distilled water. We have loved our ice maker. The plug needs to be tight Where is the fill mark? It is not indicated clearly. 선과 단어 채우기 선으로 표시됩니다. What is Noise level Very minimal. You will hear the ice drop and being flipped into the bucket. But hardly any noise while making the ice. amperage? 2 amps Does this need a water hookup ? No it doesn’t need water hook up but please be aware that your cord can get hot and catch fire! They won’t do anything about mine and I had mine for 2 months! So much for honest companies ! refrigerant type? The kind that breaks down and stops working about 31 days.. What are the electrical specs? Amps needed and so forth? plugs into electrical USA standard outlet! Are any of these ice makers made in the USA Igloo is based and manufactured in Katy, Texas What country is it made in? There is a basket inside the clear window that catches the ice cubes! Comes with a scoop and each drop of ice cubes is made every 6 minutes!Mine is on constantly in the heat of summer & I transfer to ice cube bin into my freezer when it gets full! How can the company be contacted? What is listed is not correct. It hasn't been a year and it is no longer working. It would be my understanding that the company making this product was only a licensee of the "brand" Igloo. This is my second unit, and it seemed very similar to my original unit, which I believe was actually made by Igloo. I would try to contact Igloo directly for whatever need you have with this unit. Ice maker lights flash and it is not getting water. What can we do? Water level has to be correct the item does have to be level and then turn off the ice maker and turn it back on making sure you select what kind of ice cube's you want. if it's still not getting water then the pump may not be good or is clogged What are measurements (footprint on the countertop)? The measurements are listed in the product description. But they are approximately 10" wide, 12" deep and 14" high. It needs air circulation in the back and on the right side. What is the actual diameter of the small ice it makes? (If you don't have an actual measurement please let someone else answer)? All ice cube comes in different sizes. Often times the ice are smaller in the first cycle since the machine is starting up. But once the ice is on the 3rd cycle, often times it becomes larger. Sizes vary depending on how long you run the machine. Best regards; Customer Care Representative What is the warrenty? 90 days. How loud is the machine when its making ice ? Silent until it drops the ice and that’s really not much! Does it beep to let you know its full It has a sensor that activates a light and it will not make any more ice if it is full. You will kind of know bc it is quiet when not making ice. It is an awesome machine. Are you selling ice maker or antenna?ge pro indoor tv antenna, 30 mile antenna, home decor, digital, hdtv antenna, smart tv, 4k 1080p vhf uhf, storage ice maker Is this Self cleaning No , it requires some cleaning but it is minimal in my opinion . Where is the ice maker i bought? If you haven’t received the ice maker you ordered, you should be able to go to “ My Orders” then click on “ Track Package” … that should give you estimated delivery date…. If not, go to “ Contact Us” .. Customer Service.. Call Customer Service… They should be able to help you. VIDEO Igloo-Ice-Maker-Instruction-Manual Igloo-Ice-Maker-Instruction-Manual-original www.iglooicemakers.com Post image references: Igloo-LOGO | https://manuals.plus/wp-content/uploads/2019/07/Igloo-LOGO.png Igloo Ice Maker-PRODUCT | https://manuals.plus/wp-content/uploads/2019/07/Igloo-Ice-Maker-PRODUCT.png Igloo Ice Maker | https://manuals.plus/wp-content/uploads/2019/07/Igloo-Ice-Maker.png button function with LED indicators | https://manuals.plus/wp-content/uploads/2019/07/button-function-with-LED-indicators.png Pre-Operating Instructions | https://manuals.plus/wp-content/uploads/2019/07/Pre-Operating-Instructions.png Operating Instructions | https://manuals.plus/wp-content/uploads/2019/07/Operating-Instructions.png Drain | https://manuals.plus/wp-content/uploads/2019/07/Drain.png Igloo-LOGO | https://manuals.plus/wp-content/uploads/2019/07/Igloo-LOGO.png
Read the full Q&A page
I put water in my igloo ice maker and it comes on and starts to do the cycle, but stops and says ice is full and there’s nothing in it. I made sure the basket is seated ? I tried resetting machine but nothing. It keeps stopping at the “ice full” point.
Why does my Igloo ice maker say 'ice full' when it is empty?
If your Igloo ice maker is showing the "ICE FULL" indicator when the basket is empty, it is likely a sensor issue. Here are the steps to troubleshoot this:
If the problem persists after these steps, the internal sensor or the microcomputer may be defective, and you should contact Igloo customer service for further assistance.
메모: Always ensure the unit is level and has at least 8 inches of clearance on all sides for proper ventilation, as overheating can also cause erratic behavior.
Reference: Igloo Ice Maker Manual, Operating Instructions Section 5.
Read the full Q&A page
i have bought an igloo ice maker and its been working fine i clean it once a week and it gets pretty nasty all of a sudden it just stopped working i cleaned it checked the line and reset it and its still not working and i have tried everything. this is alittle discouraging seeing it wasn’t a cheep household item and my family uses ice i am not very happy with this product can someone help me? is there a number i can call to talk with someone
Why has my Igloo ice maker stopped working after cleaning and resetting, and how can I contact customer support?
If your Igloo ice maker has stopped working despite cleaning and resetting, there are a few additional troubleshooting steps you can try:
If these steps do not resolve the issue, the manual suggests contacting your dealer or Igloo customer service for assistance. While a specific phone number is not provided in the manual text, you can visit www.iglooicemaker.com for official support and contact information. Note that many of these units carry a 90-day warranty.
Please ensure the unit is on a level surface with at least 8 inches of clearance on all sides for proper ventilation, as overheating can cause the system to shut down.
Read the full Q&A page
buenas tardes mi modelo es ICEB33SS COMIENZA A TRABAJAR Y AL RATO APARECE LUZ ROJA Y DEJA DE FUNCIONAR
Why does my Igloo ICEB33SS ice maker stop working and show a red light after starting?
The red light on your Igloo ICEB33SS ice maker typically indicates one of two common issues: the water reservoir is empty or the ice basket is full. Here are the steps to troubleshoot:
If the problem persists after these steps, the internal pump may be clogged or malfunctioning, and you may need to contact Igloo customer service for further assistance.
Note: Always ensure the unit is on a level surface and has at least 8 inches of clearance on all sides for proper ventilation.", "contextual_details_en": "Troubleshooting an Igloo ICEB33SS ice maker that shuts down with a red indicator light shortly after beginning operation.
Read the full Q&A page
Can I buy a replacement ice maker basket for my igloo model # Ice115-ss Ice maker
Where can I buy a replacement ice basket for Igloo model ICE115-SS?
To find a replacement ice basket for your Igloo ICE115-SS, you can try the following options:
When replacing the basket, ensure the temperature sensor is positioned above it so the "Ice Full" indicator functions correctly.
Read the full Q&A page
I have a ICE103 where can I get the tray that holds the water in it so the machine can make the ice, mine is broken on the side where the motor goes into? Need a new tray ?
Where can I find a replacement water tray for the Igloo ICE103 ice maker?
For replacement parts like the water tray (also referred to as the "water box" in the manual) for your Igloo ICE103, you should contact the manufacturer or an authorized parts dealer. Since Igloo ice makers are often produced under license, you may need to reach out to the specific customer service department for these appliances.
The water tray is a critical component that tilts during the ice-making cycle; if the motor connection point is broken, the unit will not be able to dump ice or refill correctly, so a full replacement of that part is necessary.
Note: If you are unable to find the part under the Igloo brand, search for the model number "ICE103" as many of these portable ice makers share identical internal components across different brand names.
If you need further assistance, you can also check the "Contact Us" section in your original purchase history if bought through a major online retailer.
Read the full Q&A page
El botón de encendido está intermitente, prende y apaga la luz led, pero no enciende la máquina, solución?
Why is the power light flashing and the ice maker not starting?
A flashing power light on your Igloo ice maker typically indicates that the machine is in a standby mode or has encountered an issue that prevents it from starting. Here are the most common solutions:
If the light continues to flash and the machine does not start after these steps, there may be a malfunction with the internal pump or sensors, and you should contact customer service.
En español: La luz intermitente suele indicar que hay hielo atascado o que la canasta está llena. Vacíe la canasta y reinicie la máquina desenchufándola por 10 minutos.
메모: If you have recently moved the unit, wait at least 2 hours for the refrigerant to settle before turning it on.
자세한 내용은 다음을 참조하세요. 이글루 제빙기 매뉴얼.
Read the full Q&A page