FitCloudPro 팔찌 사용 설명서

The manual for the FitCloudPro Bracelet does not provide a direct link to purchase replacement parts or specific pricing. However, it specifies that the device requires a 5V 0.5A~1A power adaptor for battery recharging.

To find a replacement, you should search online marketplaces (such as Amazon, eBay, or AliExpress) for a "2-pin magnetic charging cable for smartwatches." Most FitCloudPro-compatible bracelets use a standard magnetic pogo-pin charger. Before purchasing, please measure the distance between the two charging contact points on the back of your bracelet to ensure the pins on the new cable align correctly (common distances are 2.84mm or 4.0mm).

Yes, using a cane in the same hand as your FitCloudPro bracelet is likely the cause of the inaccurate step count. Most fitness trackers, including this bracelet, use a 3-axis accelerometer to detect the specific swinging motion of your arm to count steps. When you use a cane, your arm movement is restricted or altered, which prevents the sensor from recognizing the motion as a step.

To improve accuracy, you can try the following:

• Switch Wrists: Wear the bracelet on your right arm (the arm not using the cane). If you do this, ensure you update the settings in the FitCloudPro app under Mine > Band location to select the correct hand.
• Check Personal Data: Ensure your height and weight are correctly set in the app under Mine > Click ID, as these metrics help calculate stride and movement data.
• 펌웨어: Ensure your device is synced with the app to receive any potential algorithm updates that might improve motion detection.

To restore message notifications on your FitCloudPro bracelet, please check the following settings based on the manual's requirements:

• 앱 알림 활성화: Open the FitCloudPro app, go to the 장치 or 내 거 section, and select Message Notification Push (or 'Notifications push'). Ensure the toggle is turned on for the specific apps you want alerts from, such as Facebook, Twitter, or Skype.
• Check Background Permissions: Ensure the FitCloudPro app is allowed to run in the background. On some phones, you may need to check your 'Mobile Manager' or battery optimization settings to prevent the system from closing the app.
• System Bluetooth Pairing: Ensure your phone's Bluetooth is on and the bracelet is correctly bound within the app. If you are using an iPhone, ensure that 'Share System Notifications' is enabled in your phone's Bluetooth settings for the connected device.
• 방해 금지: Verify that the bracelet is not in a 'Do Not Disturb' mode, which would silence incoming alerts.

If these steps do not work, try the 다시 놓기 function found under the device settings (section 3.2.13) to restore the bracelet to factory defaults before re-pairing.

To change the watch face (dial) on your FitCloudPro bracelet, you can use the following methods based on the manual:

• 장치에서: According to section 2.2.2, you can rotate the side button to switch between different pre-loaded dials directly on the watch interface.
• 앱을 통해: To access the full library of watch faces (including the 200+ faces often advertised), open the FitCloudPro app on your smartphone. Navigate to the 장치 menu and look for 다이얼 설정 (section 3.2.5). From there, you can browse the online dial gallery and upload new faces to your bracelet.

Please ensure your bracelet is successfully paired with the app via Bluetooth to sync new watch faces.

Based on the FitCloudPro Bracelet manual, there is no specific application or dedicated sport mode listed for water gymnastics or 'aquaforme'.

The manual lists the following supported multi-sport modes under section 2.5: Running, Walking, Climbing, Riding, Table Tennis, Badminton, Basketball, and Skipping. While the device may have basic water resistance, the manual does not explicitly mention swimming or water-based exercise tracking. You may check the FitCloudPro app on your smartphone to see if additional sport modes have been added via software updates, but they are not documented in the standard user guide.

If the map for your exercises has stopped displaying in the FitCloudPro app, it is usually related to GPS permissions or background data settings on your smartphone. Please try the following steps:

• Check GPS Permissions: Ensure that the FitCloudPro app has permission to access your location "Always" or "While using the app."
• Background Activity: As noted in section 4.2 of the manual, ensure the app is allowed to run in the background. If you have a "Mobile manager" or battery optimization active, it may kill the app's process, preventing GPS tracking.
• GoogleFit Sync: If you use GoogleFit, ensure the sync is still active under the "Mine" section (3.3.2) of the app.
• 연결 확인: Verify that your phone's Bluetooth and GPS are both turned on before starting an exercise.

If the issue persists, try unbinding the device (3.2.14) and re-pairing it, or clearing the app cache in your phone settings.