deli T313 Split Comb Binding Machine
위에view
Model T313 Deli comb binding machine is designed for punching paper and plastic sheets, and using a plastic clip with a rubber ring for loose-leaf document binding. Read this manual to ensure correct use and higher binding efficiency.
명세서
| 매개변수 | 값 |
|---|---|
| 모델 | T313 |
| 최대 펀칭 두께 | 20 sheets of paper (80g A4 paper) |
| Binding edge distance | 2~5mm |
| Hole size and pitch | 3 mm × 8 mm, 14.3 mm pitch |
| 바인딩 사양 | A4 size paper or smaller |
| 최대 바인딩 두께 | 450장 |
| 순중량 | 6.35kg |
| 장치 치수 | 405mm × 315mm × 380mm |
- Consumable comb thickness recommendations (mm → sheets): 620→22180; 840→25210; 1060→28240; 1280→32280; 1410→35350; 16120→38360; 18140→45400; 20160→51450.
Quick Setup & Use
- Before punching original materials, test with waste paper to confirm the machine works normally.
- Set punching position: Set the locating block to the desired position. Loosen by turning the knob counterclockwise, then fasten by turning it clockwise.
- Set edge margin: Turn the punching margin control to set the edge margin.
- 펀칭: If punching an odd-sized document, pull out and disengage the proper punch selector. Insert paper into the punching channel, pull the handle all the way down until it stops to punch completely through, then pull the handle up and remove the punched paper.
- Empty waste container: Empty the paper scrap box periodically.
- 제본: Place the rubber ring behind the comb-shaped plate and move it left with the opening facing upward. Rotate the pull ring handle clockwise to open the rubber ring, then put the punched file onto the rubber ring. Rotate the pull ring handle counterclockwise to remove the file.
Product Structure & Components
- 핸들
- Comb plate
- Pull ring plate
- Pull selector
- 5Locating block
- Pull ring handle
- Punching margin control
- 종이 스크랩 상자
Consumable Specification Recommendations
| Comb (mm) | 시트 | Comb (mm) | 시트 |
|---|---|---|---|
| 6 | 20 | 22 | 180 |
| 8 | 40 | 25 | 210 |
| 10 | 60 | 28 | 240 |
| 12 | 80 | 32 | 280 |
| 14 | 100 | 35 | 350 |
| 16 | 120 | 38 | 360 |
| 18 | 140 | 45 | 400 |
| 20 | 160 | 51 | 450 |
사용 방법
- 이 기계는 종이와 플라스틱 시트의 펀칭에 사용되며 플라스틱 클립은 루스리프 제본에 사용됩니다. 이 용도로만 기계를 사용할 수 있으며 작동 지침에 따라 사용하십시오.
- 원재료를 펀칭하기 전에 폐지를 사용하여 기계가 정상적으로 작동하는지 테스트하는 것을 잊지 마십시오.
- 폐기물 용기를 주기적으로 비우십시오.
- 펀칭 상한 개수는 20개이며, 이 개수를 초과해서는 안 됩니다.
Punching Steps
- Set the locating block at the desired position. Turn the knob counterclockwise to loosen. Turn it clockwise to fasten.
- Turn the punching margin control to set the edge margin.
- Pull out and disengage the proper punch selector when punching odd-sized documents.
- Push paper into the punching channel. Pull the handle all the way down until it stops to punch completely through. Pull the handle up completely and remove the punched paper.
바인딩 단계
- Place the rubber ring behind the comb-shaped plate and move the rubber ring to the left with the opening facing upwards.
- Rotate the pull ring handle clockwise to open the rubber ring and then put the punched file onto the rubber ring.
- Rotate the pull ring handle counterclockwise to remove the file.
Troubleshooting and Common Fault Analysis
| 결함 현상 | 고장 원인 분석 | 문제 해결 방법 |
|---|---|---|
| It is hard to press the handle when punching paper. | There is paper scrap or another foreign object in the paper cutting area. | Take out the debris with chipboard. |
| The operating load is beyond the recommended punching capacity. | Operate according to the limits described in the instructions. | |
| The punching edge distance has an uneven inclination. | The two sides of the incoming paper are unbalanced/misaligned. | Align both sides of the paper evenly. |
| There is paper scrap or another foreign object in the paper cutting area. | Take out the debris with chipboard. | |
| The open rubber ring displays uneven alignment. | The comb plate has deformation caused by a collision. | Straighten the comb plate using a straightedge or ruler. |
| The draw hook of the pull ring plate is deformed. | Calibrate and adjust the draw hook by hand. | |
| Incomplete paper punching or the paper is difficult to extract. | The number of sheets being punched at one time is too large. | Reduce the punching thickness per pass, adhering to the instruction limits. |
| The paper cannot reach the bottom of the slot. | The paper is damaged or the edge is curl주고받음. | Smoothen the paper edges and try again. |
제품 매개변수
- 최대 펀칭 두께: 20 sheets of paper (80g A4 paper)
- Binding edge distance: 2~5mm
- Hole Size and Pitch: 3mm × 8mm, 14.3mm pitch
- 바인딩 사양: A4 size paper or smaller
- 최대 바인딩 두께: 450장
- 순중량: 6.35kg
- 장치 치수: 405mm × 315mm × 380mm
보증 카드
구매해주셔서 감사합니다asing our products. The interests of customers who purchase our products will be protected. For any malfunction due to product manufacturer quality issues, please contact authorized local dealers or service centers with this receipt and the warranty card.
보증 조건:
- For product failures occurring under normal operating circumstances, free of charge repair and spare parts replacement services shall be provided by our company within one year commencing from the date of purchase.
- Customers are required to present this warranty card and the original purchase invoice to our company upon requesting warranty service. This warranty card shall be valid only after the following form is filled out in detail and affixed with the official seal of the dealer.
- 다음과 같은 경우에는 무상 수리 서비스를 제공하지 않습니다.
- 보증 기간 만료
- 사용 설명서의 요구 사항을 따르지 않은 부적절한 사용, 유지 관리 또는 보관으로 인해 발생한 손상
- 무단 분해, 수리 또는 개조로 인한 고장 또는 손상
- 불가항력으로 인한 고장 또는 손상
- Wear parts or consumable accessories.
This warranty card is delivered with the product (one card per product). Please keep this warranty card in a secure place to claim free warranty service. It will not be replaced if lost.
Warranty Registration RecordsDate of Purchase: ______ Year ______ Month ______ Day
| 제품 정보 | 제품 이름 | 일련번호 | ||
| 제품 모델 번호 | T313 | 제조일자 | ||
| 고객 정보 | 회사 이름 | |||
| 주소 | 연락하다 | |||
| 판매 정보 | 딜러 이름 | 핸드폰 | ||
| 주소 | 연락하다 | |||
| 유지 관리 기록 | 구매일자 | 핸드폰 | ||
| 오작동에 대한 설명 | 유지 보수 결과 | 고객 서명 | 기술자 서명 | 유지 보수 날짜 |
(Dealer Copy: This copy shall be cut along the dotted line and retained by the dealer.)
| 제품 정보 | 제품 이름 | 일련번호 | ||
| 제품 모델 번호 | T313 | 제조일자 | ||
| 고객 정보 | 회사 이름 | |||
| 주소 | 연락하다 | |||
| 판매 정보 | 딜러 이름 | 핸드폰 | ||
| 주소 | 연락하다 | |||
| 유지 관리 기록 | 구매일자 | 핸드폰 | ||
| 오작동에 대한 설명 | 유지 보수 결과 | 고객 서명 | 기술자 서명 | 유지 보수 날짜 |
문제 해결
| 결함 현상 | 가능성 있는 원인 | 문제 해결 방법 |
|---|---|---|
| Hard to press the handle when punching paper | Paper scrap or another foreign object in the paper cutting area | Take out the debris with chipboard. |
| Hard to press the handle when punching paper | Operating load beyond the recommended punching capacity | Operate according to the limits described in the instructions. |
| Punching edge distance uneven inclination | Incoming paper sides unbalanced/misaligned | Align both sides of the paper evenly. |
| Punching edge distance uneven inclination | Paper scrap or foreign object in the paper cutting area | Take out the debris with chipboard. |
| Open rubber ring shows uneven alignment | Comb plate deformation from collision | Straighten the comb plate using a straightedge or ruler. |
| Open rubber ring shows uneven alignment | Draw hook of the pull ring plate deformed | Calibrate and adjust the draw hook by hand. |
| Incomplete paper punching or paper difficult to extract | Number of sheets being punched at one time too large | Reduce the punching thickness per pass, adhering to instruction limits. |
| Paper cannot reach the bottom of the slot | Paper damaged or edge curl잉 | Smoothen paper edges and try again. |
더 많은 정보
- DELI GROUP CO., LTD. 301 Xuxiake Ave. Ninghai County Ningbo 315600 China Made in China
- info@nbdeli.com
- www.deliworld.com
- 22) PAP Reserved For Use Version: 1.0Date: 5-2025
문서 / 리소스
 | T313 Split Comb Binding Machine |
참고문헌
- 사용자 설명서manual.tools
Published: July 24, 2026