소개
The COROS Bike Cadence Sensor is designed to help cyclists track their pedaling RPMs (revolutions per minute) to improve pedaling efficiency. This sensor is compatible with both outdoor and indoor rides, including most spin bikes, and pairs seamlessly with bike computers, smartwatches, or smartphones via Bluetooth connectivity.
상자 안에 무엇이 들어있나요?
패키지를 열면 다음과 같은 구성품이 들어 있습니다.
- COROS Bike Cadence Sensor
- 센서 마운트
- Rubber Bands for mounting
- 빠른 시작 가이드
- 제품 안전 정보
설정 및 설치
1. 배터리 설치
The COROS Bike Cadence Sensor uses a CR2032 coin cell battery. Ensure the battery is correctly inserted before use. The battery compartment is typically located on the back of the sensor.
2. 센서 장착
The sensor is designed for easy installation on your bike's crank arm. Use the provided rubber bands to securely attach the sensor. Position the sensor on the non-drive side crank arm for optimal cadence tracking.
3. 장치와 페어링
The COROS Bike Cadence Sensor connects via Bluetooth. To pair, activate the sensor by rotating the crank arm a few times. Then, open the settings on your compatible bike computer, smartwatch, or smartphone application and search for new Bluetooth devices. Select the COROS Cadence Sensor from the list to establish a connection. The sensor is not compatible with ANT+ devices.
작동 지침
Once paired, the sensor will automatically begin tracking your pedaling RPMs when you start cycling. This data is transmitted in real-time to your connected device, allowing you to monitor and optimize your pedaling efficiency. The sensor works effectively for both outdoor rides and indoor training sessions, including use with most spin bikes.
유지
배터리 수명 및 교체
The CR2032 battery in your COROS Bike Cadence Sensor is designed to last up to 12 months under typical usage conditions. When the battery level is low, your connected device may display a notification. To replace the battery, carefully open the battery compartment, remove the old battery, and insert a new CR2032 battery with the positive (+) side facing up. Ensure the compartment is sealed tightly after replacement.
세척 및 방수 기능
The sensor has an IP67 water rating, providing protection against dust and temporary immersion in water. This makes it suitable for all-weather protection and durability. To clean the sensor, wipe it with a damp 천으로 닦으세요. 기기를 손상시킬 수 있는 강한 화학 물질이나 연마재는 사용하지 마세요.
문제 해결
- 센서가 연결되지 않음: Ensure the sensor has a fresh battery and is properly activated by rotating the crank arm. Check that Bluetooth is enabled on your receiving device and that the sensor is within range.
- 부정확한 판독: Verify that the sensor is securely mounted on the crank arm and is not obstructed. Ensure there are no strong electromagnetic interferences nearby.
- 배터리가 빨리 소모됨: Confirm that the sensor is not left in an active state when not in use. Replace the battery if it is old or if the issue persists.
명세서
| 상표 | 코로스 |
| 모델명 | COROS Bike Cadence Sensor |
| 색상 | 검은색 |
| 센서 유형 | 케이던스 센서 |
| 연결 기술 | Bluetooth (Not compatible with ANT+ devices) |
| 장착 유형 | 크랭크 암 마운트 |
| 배터리 유형 | CR2032 리튬 망간 이산화물 |
| 배터리 수명 | 최대 12개월 |
| 물 등급 | IP67 |
| 무게 | 11g |
| 품목 치수(LxWxH) | 3.94 x 3.94 x 3.94 인치 |
보증 및 지원
The COROS Bike Cadence Sensor comes with a 1-year manufacturer's warranty. For technical support, warranty claims, or additional product information, please visit the official COROS web사이트를 방문하거나 고객 서비스에 직접 문의하세요. 보증 확인을 위해 구매 증빙 자료를 보관하세요.
