1. 제품 오버view
The Acmount D18 is a versatile emergency car kit combining a powerful jump starter, a 150PSI tire inflator, a 21800mAh power bank, and a 600 lumen LED emergency light. Designed for reliability and ease of use, it is suitable for various vehicles and outdoor activities.
Figure 1: Acmount D18 Jump Starter with Air Compressor
2. 패키지 내용
패키지에 모든 품목이 들어 있는지 확인하세요.
- Portable Jump Starter with Air Compressor (1)
- Air Pump Hose (1)
- Gas Nozzles (4)
- Cl이 포함된 스마트 점퍼 케이블amps (1)
- USB-A to C Charge-In Cable (1)
- Portable Carrying Case (1)
- 사용자 설명서 (1)
Figure 2: All components included in the Acmount D18 package.
3. 안전 정보
The Acmount D18 is equipped with 10 intelligent safety protections to ensure safe operation. Always follow these guidelines:
- 역충전 보호: Prevents current flow back to the jump starter from the vehicle battery.
- 역 극성 보호 : Ensures correct connection to battery terminals. The smart clip indicator light will notify of incorrect use.
- 오버볼tage 보호: 과도한 볼륨에 대한 보호 장치tage.
- 저온 보호: Operates safely in temperatures down to -4°F (-20°C).
- 고온 보호: Operates safely in temperatures up to 140°F (60°C).
- 과전류 보호: 과도한 전류 소모로부터 보호합니다.
- 과충전 보호 : 과충전으로 인한 배터리 손상을 방지합니다.
- Anti-Spark Protection: 연결 중 스파크 발생 위험을 최소화합니다.
- 과부하 보호: Shuts down if the load exceeds safe limits.
- 단락 보호: 단락으로 인한 손상을 방지합니다.
Always ensure the smart clip indicator light shows a solid green before attempting to jump start.
Figure 3: Built-in safety features for secure operation.
4. Getting Started: Charging the Unit
Before first use, fully charge the Acmount D18. It is recommended to recharge the unit every three months to maintain optimal battery health, even when not in use.
- Locate the USB-C input port on the side of the unit, protected by a silicone cover.
- Connect the provided USB-A to C charging cable to the unit and a suitable USB power adapter (not included).
- The LCD display will indicate the charging status. Charge until the battery indicator shows full.
5. Operating the Jump Starter
The Acmount D18 can deliver a peak current of 6000A, capable of starting all gasoline engines and 10.0L diesel engines.
- 연결 Clamps: Open the engine start port cover on the unit. Connect the smart jumper cable to the unit. Ensure it is fully inserted.
- 배터리에 연결하세요: 빨간색 cl을 연결하세요amp 차량 배터리의 양극(+) 단자와 검은색 clamp (-) 단자에.
- 연결 확인: Wait for the LED indicator on the smart jumper cable to light up solid green. If it flashes red/green or shows no light, check connections for proper polarity and contact.
- 차량 시작: 자동차 엔진을 켭니다.
- Cl 제거amps: 엔진이 시동되면 cl을 제거하십시오.amps from the car battery within 30 seconds, then disconnect the smart jumper cable from the Acmount D18.
Figure 4: Easy steps for jump-starting your vehicle.
Video 1: Official Acmount demonstration of the jump starter and air compressor features.
6. Operating the Tire Inflator
The integrated air compressor can inflate up to 150PSI, delivering 45L/min high airflow. It features automatic pressure detection and auto shut-off.
- 공기 호스 연결: Screw the air pump hose into the designated port on the Acmount D18.
- Attach to Tire: Connect the other end of the hose to the tire valve. Use appropriate gas nozzles for different inflatables (e.g., bicycle tires, balls, air cushions).
- 전원 켜기 및 모드 선택: Press the power button to turn on the unit. Use the 'M' button to cycle through 5 inflation modes (Car, Motorcycle, Bicycle, Ball, Custom Mode) and the '+' / '-' buttons to set the desired pressure. The LCD digital display supports PSI/BAR/KPA units.
- 인플레이션 시작: Press the 'Start/Stop' button to begin inflation. The unit will automatically stop once the preset pressure is reached.
- 연결 해제: Remove the hose from the tire valve.
Figure 5: Simple steps for tire inflation.
7. 보조배터리로 사용하기
The 21800mAh battery can charge phones, tablets, and other devices via its dual USB output ports.
- Locate the USB output ports (USB1-OUT, USB2-OUT) and the USB-C IN port on the side of the unit, protected by a silicone cover.
- Connect your device's charging cable to the appropriate USB output port on the Acmount D18. USB2-OUT supports fast charging.
- 이 장치는 자동으로 기기 충전을 시작합니다.
Figure 6: Charging electronic devices with the integrated power bank.
8. LED 비상등 사용
The Acmount D18 features a 600 lumen LED light with three modes for various emergency situations.
- 빛 활성화: Press the light button (usually indicated by a lightbulb icon) on the unit to turn on the flashlight.
- 사이클 모드: Press the light button repeatedly to cycle through the modes: Flashlight (steady beam), SOS (Morse code signal), and Strobe (rapid flashing).
- 끄기: Continue pressing the light button until the light turns off, or long-press the button.
Figure 7: The multi-mode LED light provides illumination and signaling capabilities.
9. 사양
| 특징 | 사양 |
|---|---|
| 상표 | 산하다 |
| 모델 | 디18 |
| 피크 출력 전류 | 6000 Amps |
| 배터리 용량 | 21800mAh |
| 타이어 팽창기 압력 | 최대 150PSI |
| 기류 율 | 45L/분 |
| 엔진 호환성 | All Gasoline Engines, 10.0L Diesel Engines |
| LED 광 출력 | 600 Lumens (Flashlight/SOS/Strobe) |
| USB 출력 포트 | Dual USB (one QC 3.0 fast charging) |
| 충전 입력 | USB-C |
| 작동 온도 | -4°F ~ 140°F(-20°C ~ 60°C) |
| 품목 무게 | 3.52파운드(1.6킬로그램) |
10. 유지관리
To ensure the longevity and optimal performance of your Acmount D18, follow these maintenance tips:
- 일반 충전: Recharge the unit every three months, even if not used, to prevent deep discharge and prolong battery life.
- 저장: Store the unit in its portable carrying case in a cool, dry place, away from direct sunlight and extreme temperatures.
- 청소: 부드럽고 마른 천으로 닦으세요. 강한 화학 물질이나 연마성 세제는 사용하지 마세요.
11. 문제 해결
If you encounter issues with your Acmount D18, refer to the following common troubleshooting steps:
- 장치가 켜지지 않음: Ensure the unit is charged. If the battery is completely depleted, it may take a few minutes of charging before it powers on.
- 점프 스타터가 작동하지 않음:
- Check the smart clip indicator light: A solid green light indicates a correct connection. If it's flashing or red, recheck the clamps for proper polarity and secure contact with the battery terminals.
- Ensure the smart jumper cable is fully inserted into the unit's engine start port.
- The vehicle battery might be severely discharged. Allow the jump starter to connect for a few minutes before attempting to start.
- Tire Inflator Not Working:
- Ensure the air pump hose is securely screwed into the unit and properly connected to the tire valve.
- Check the selected inflation mode and target pressure on the LCD display.
- Verify the unit has sufficient battery charge.
- Device Not Charging via USB: Ensure the USB cable is properly connected to both the Acmount D18 and your device. Check if the unit has enough power.
문제가 지속되는 경우 고객 서비스에 문의하세요.
12. 보증 및 지원
Acmount provides lifetime technical support and 24/7 customer service. If you have any questions or require assistance, please contact our professional after-sales team for a satisfactory solution.
Contact information can typically be found on the product packaging or the official Acmount web대지.
