1. 서론
This manual provides essential information for setting up, operating, and maintaining your waveshare ESP32-S3 3.5-inch Capacitive Touch Display Development Board. Please read these instructions carefully to ensure proper use and to maximize the functionality of your device.
The ESP32-S3-Touch-LCD-3.5 is a versatile development board featuring an ESP32-S3R8 Xtensa 32-bit LX7 dual-core processor, a 3.5-inch 320x480 pixel IPS capacitive touch display, and integrated Wi-Fi and Bluetooth 5 (LE) connectivity. It is designed for various smart device development applications, including human-machine interaction, data recording, and media playback.
2. 주요 특징
- 프로세서: Equipped with ESP32-S3R8 Xtensa 32-bit LX7 dual-core processor, up to 240MHz main frequency.
- 무선 연결 : Supports 2.4GHz Wi-Fi (802.11 b/g/n) and Bluetooth 5 (LE) with an onboard antenna.
- 메모리: Built-in 512KB SRAM and 384KB ROM, with onboard 8MB PSRAM and an external 16MB Flash memory.
- 표시하다: 3.5-inch capacitive touch display with 320 × 480 resolution and 262K colors. Features an IPS panel for wide view각도를 나타냅니다.
- Display & Touch Drivers: Built-in ST7796 display driver (SPI communication) and FT6336 capacitive touch chip (I2C communication).
- 센서: Onboard QMI8658 6-axis IMU (3-axis accelerometer and 3-axis gyroscope) for motion detection.
- 실시간 시계(RTC): Onboard PCF85063 RTC chip, powered by main Lithium battery via AXP2101, with a reserved RTC battery header for backup.
- 전원 관리 : Adopts AXP2101 IC for efficient power management, supporting multiple voltage outputs, battery charging, and optimization.
- 연결성: Type-C connector, I2C, UART, USB, and multiple GPIO pins for peripherals and debugging.
- 저장: Onboard TF card slot for extended storage and data transfer.
- 카메라 인터페이스: Compatible with mainstream cameras such as OV2640 and OV5640.
- 오디오: Integrated audio input and output, enabling AI interaction and offline voice control.
- 프로그래밍 가능한 버튼: Onboard PWR and BOOT buttons for custom function development.
그림 2.1: 이상view of the waveshare ESP32-S3 3.5-inch Capacitive Touch Display Development Board, highlighting its integrated audio, Wi-Fi, and BLE 5 capabilities.
Figure 2.2: The development board supports 2.4GHz Wi-Fi (802.11 Ax/B/G/N) and Bluetooth 5 (LE) for robust wireless communication.
Figure 2.3: The IPS display panel offers excellent display performance with 262K colors and a wide view각도 178도.
3. 설정 지침
3.1 전원 연결
- Connect the development board to a power source using the Type-C USB connector. This port also facilitates data communication and programming.
- If using a Lithium battery, connect it to the onboard 3.7V MX1.25 Lithium battery recharge/discharge header. The AXP2101 IC manages battery charging and power.
- For RTC backup, a dedicated RTC battery header is available for connecting a backup battery.
3.2 소프트웨어 환경
The ESP32-S3-Touch-LCD-3.5 supports popular development environments:
- ESP-IDF: Espressif IoT Development Framework, a comprehensive SDK for ESP32 series.
- 아두이노 IDE: An open-source electronic prototyping platform, convenient for beginners and experienced developers.
Refer to the official waveshare development resources for detailed guides on setting up these environments and getting started with programming examp레.
Figure 3.1: The board supports both ESP-IDF and Arduino IDE, offering comprehensive SDKs and tutorials for easy development.
4. 사용 설명서
4.1 기본 작업
- 전원 켜기/끄기: Connect the Type-C USB cable to power the board. The PWR button can be programmed for specific power control functions.
- Capacitive Touch Display: Interact with the 3.5-inch display using touch gestures. The FT6336 chip handles touch input.
- 프로그래밍 가능한 버튼: The PWR and BOOT buttons can be configured for various functions within your application. The BOOT button is typically used for entering download mode during firmware flashing.
Figure 4.1: The capacitive touch display allows for intuitive human-machine interaction, suitable for various smart device applications.
4.2 고급 기능
- AI Interaction & Voice Control: Utilize the integrated audio input and output for AI speech interaction and offline voice control applications.
- 카메라 통합: Connect compatible cameras (e.g., OV2640, OV5640) to the onboard camera interface for image capture and video monitoring.
- 외부 주변 장치: Use the I2C, UART, USB, and GPIO pins to connect and control various external sensors, actuators, and modules.
- 데이터 저장: Insert a TF card into the dedicated slot for extended storage, data logging, and media playback.
5. 핀 정의
The development board provides a comprehensive set of GPIO pins and interfaces. Refer to the diagram below for the pinout and their functions.
Figure 5.1: Detailed pin definition diagram for the ESP32-S3-Touch-LCD-3.5 board, showing power, ground, GPIO, UART, I2C, KEY, and USB pins.
For specific pin assignments and their alternative functions, consult the official ESP32-S3 datasheet and waveshare development resources.
6. Onboard Components
The board integrates various components to enhance its functionality. The following diagram illustrates the layout and identification of these components.
Figure 6.1: Diagram showing the various onboard components of the ESP32-S3-Touch-LCD-3.5, with numbered labels for identification.
- ESP32-S3R8: The SoC with Wi-Fi and Bluetooth, up to 240MHz operating frequency, with onboard 8MB PSRAM.
- Onboard antenna.
- W25Q128JVSJQ: 16MB NOR-Flash.
- Camera interface: Supports mainstream cameras such as OV5640 / OV2640.
- TF 카드 슬롯.
- IPEX 1 antenna connector: Reserved connector, enabled via resoldering an onboard resistor.
- MX1.25 speaker header.
- 리셋 버튼.
- 전원 버튼.
- AXP2101: Highly integrated power management IC.
- 충전 표시기.
- USB Type-C 포트.
- ES8311: Low power audio codec chip.
- 전원 공급 표시기.
- 마이크로폰.
- SM1.0 RTC battery header: For connecting rechargeable RTC battery.
- MX1.25 Lithium battery header: MX1.25 2P connector, for 3.7V Lithium battery, supports charging and discharging.
- 2.54mm pitch GPIO header: Adapting available IO function pins for easy expansion.
- PCF85063: RTC chip.
- QMI8658: 6-axis IMU includes a 3-axis gyroscope and a 3-axis accelerometer.
7. 카메라 지원
The ESP32-S3-Touch-LCD-3.5 development board includes a camera interface compatible with mainstream camera modules such as OV2640 and OV5640. This allows for integration into applications requiring image capture, video monitoring, and other vision-based functionalities.
Figure 7.1: The board's camera interface supports modules like the OV5640 5MP camera, suitable for image capture and video monitoring applications.
Note: The OV5640 5MP camera module is typically included only in the ESP32-S3-Touch-LCD-3.5-C version. Please check your product package for included accessories.
8. 외형 치수
The physical dimensions of the ESP32-S3-Touch-LCD-3.5 board are provided below for integration into custom enclosures or projects.
Figure 8.1: Detailed outline dimensions of the ESP32-S3-Touch-LCD-3.5 development board in millimeters.
9. 사양
| 특징 | 세부 사항 |
|---|---|
| 프로세서 | ESP32-S3R8 Xtensa 32-bit LX7 dual-core, up to 240MHz |
| 무선 연결 | 2.4GHz Wi-Fi(802.11 b/g/n), 블루투스 5(LE) |
| 온보드 메모리 | 512KB SRAM, 384KB ROM, 8MB PSRAM |
| 외부 플래시 | 16MB 플래시 메모리 |
| 디스플레이 크기 | 3.5인치 |
| 디스플레이 해상도 | 320 × 480 픽셀 |
| 디스플레이 유형 | IPS, 262K color |
| 터치타입 | 용량성 |
| 아이무 | QMI8658 6-axis (3-axis accelerometer, 3-axis gyroscope) |
| RTC Chip | PCF85063 |
| 전원 관리 IC | AXP2101 |
| USB 커넥터 | C타입 |
| 저장 공간 확장 | TF 카드 슬롯 |
| 카메라 인터페이스 | Compatible with OV2640, OV5640 |
| 패키지 크기 | 4 x 3 x 0.5 인치 |
| 품목 무게 | 2.46 온스 |
| 품목 모델 번호 | ESP32-S3 3.5inch Touch Scrren |
| 첫 번째 이용 가능 날짜 | 18년 2025월 XNUMX일 |
10. 유지관리
- 청소: 디스플레이와 기판을 닦을 때는 부드럽고 마른 천을 사용하십시오. 강한 화학 약품이나 연마재는 사용하지 마십시오.
- 손질: Handle the board by its edges to avoid touching sensitive components. Static electricity can damage electronic components, so use anti-static precautions if possible.
- 저장: 도마는 직사광선과 극한 온도 변화를 피해 건조하고 서늘한 곳에 보관하십시오.
- 배터리 관리 : If using a Lithium battery, follow standard battery safety guidelines. Avoid overcharging or deep discharging.
11. 문제 해결
- 보드 전원이 켜지지 않음: Ensure the Type-C USB cable is securely connected to a working power source. If using a battery, check its charge level and connection.
- 디스플레이가 작동하지 않음: Verify power supply. Check for any loose connections to the display. Ensure your software is correctly initializing the ST7796 display driver.
- 터치가 응답하지 않음: Confirm that the FT6336 touch chip is correctly initialized in your software and that the I2C communication is functioning.
- Wi-Fi/블루투스 문제: Check antenna connection. Ensure your software configuration for Wi-Fi or Bluetooth is correct, including SSID, password, and mode.
- 프로그래밍 오류: Double-check your code for syntax errors and logical flaws. Ensure the correct board and port are selected in your IDE. Try using the BOOT button to enter download mode if flashing fails.
For more detailed troubleshooting steps and common issues, refer to the waveshare development resources and community forums.
12. 지원
waveshare provides comprehensive development resources, including documentation, code examples, and tutorials, to assist you with your projects. If you encounter any problems or require further assistance, please contact waveshare customer support.
You can find additional information and resources on the official waveshare web사이트 또는 Amazon 스토어 페이지를 통해: Visit the waveshare Store
