Komshine FX39 광섬유 융착 접속기 및 KIP-600V 광섬유 검사 프로브 사용 설명서

1. 서론

This manual provides detailed instructions for the safe and efficient operation, maintenance, and troubleshooting of the Komshine FX39 Fiber Fusion Splicer and the Komshine KIP-600V Fiber Inspection Probe. Please read this manual thoroughly before using the equipment to ensure optimal performance and longevity.

The Komshine FX39 is a high-performance fiber fusion splicer designed for precise optical fiber splicing. The Komshine KIP-600V is a fiber inspection probe used for examining fiber end-faces.

2. 안전 정보

WARNING: Always follow safety precautions to prevent injury or damage to the equipment.

• Do not look directly into the fiber end-face or the splicing arc. Invisible laser radiation and intense light can cause severe eye damage.
• Ensure the equipment is used in a clean, dry environment, free from dust and excessive humidity.
• Handle optical fibers with care. Fiber shards are extremely sharp and can cause injury.
• Use only the specified power adapter and battery for the device.
• Keep the splicing area clear of flammable materials.

3. 패키지 내용

패키지에 모든 구성품이 들어 있는지 확인하십시오. 누락되거나 손상된 구성품이 있는 경우 즉시 공급업체에 연락하십시오.

Figure 3.1: Complete package contents including the FX39 Splicer, KIP-600V Probe, and accessories.

패키지에는 일반적으로 다음이 포함됩니다.

• Komshine FX39 Fiber Fusion Splicer
• Komshine KIP-600V 광케이블 검사 프로브
• 섬유 절단기
• 파이버 스트리퍼
• 전원 어댑터 및 충전 케이블
• Rechargeable Battery (7800mAh for FX39, 4000mAh for KIP-600V)
• 예비 전극
• 냉각 트레이
• 운반 케이스
• Cleaning Wipes and Alcohol Bottle
• 사용 설명서 (본 문서)

4. 설정

4.1. 배터리 충전

Before initial use, fully charge the device batteries. The FX39 Splicer uses a 7800mAh battery, and the KIP-600V Probe uses a 4000mAh battery.

1. 전원 어댑터를 기기와 전원 콘센트에 연결하세요.
2. 충전 표시등이 켜집니다.
3. A full charge for the FX39 typically takes approximately 3.5 hours.

Figure 4.1: The FX39 Splicer's 7800mAh battery provides up to 400 splice and heat cycles per charge.

4.2. Installing Electrodes (FX39 Splicer)

The FX39 Splicer features a tool-less electrode replacement design.

1. Ensure the splicer is powered off.
2. Gently unscrew the electrode covers.
3. 오래된 전극을 제거하십시오.
4. Insert new electrodes, ensuring they are seated correctly.
5. Screw the electrode covers back into place.

Figure 4.2: Tool-less electrode replacement for convenience and efficiency.

4.3. 작업 공간 준비

Set up the splicer on a stable, clean, and level surface. Ensure adequate lighting and ventilation. Keep all necessary tools and consumables within reach.

5. 사용 설명서

5.1. Komshine FX39 Fiber Fusion Splicer Operation

The FX39 Splicer features 6-motor core alignment and a 4.3-inch capacitive touch screen for intuitive operation.

Figure 5.1: The 6-motor positioning system ensures precise fiber alignment for optimal splicing.

5.1.1. Fiber Preparation

1. 섬유를 벗겨내세요: Use a fiber stripper to remove the protective coating from the fiber, exposing the bare fiber.
2. 섬유를 깨끗하게 세척하세요: Clean the bare fiber with a lint-free wipe soaked in 99% isopropyl alcohol.
3. 섬유를 분리하세요: Use a high-precision fiber cleaver to achieve a clean, perpendicular fiber end-face. The cleave length should be appropriate for the splicer's fiber holders.

5.1.2. Placing Fiber in Splicer

The FX39 supports a 3-in-1 fiber holder design.

1. Open the splicer's wind cover and fiber clamps.
2. Carefully place the prepared fibers into the V-grooves of the fiber holders. Ensure the fiber end-faces are positioned correctly near the electrodes.
3. 광섬유를 닫으세요amps and then the wind cover.

Figure 5.2: The 3-in-1 fiber holder accommodates various fiber types and sizes.

5.1.3. Splicing Process

1. The splicer will automatically begin the alignment process. The 6 motors will precisely align the fiber cores.
2. Once aligned, the splicer will initiate the fusion arc. The splicing process takes approximately 6 seconds.
3. After splicing, the estimated splice loss will be displayed on the screen.
4. Open the wind cover and carefully remove the spliced fiber.

5.1.4. Heat Shrink Protection

1. Slide a heat shrink sleeve over the splice point.
2. Place the fiber with the sleeve into the heating oven.
3. Close the oven lid. The heating process takes approximately 16 seconds.
4. Once complete, carefully remove the protected splice and allow it to cool on the integrated cooling tray.

Figure 5.3: The 2-layer cooling tanks provide a safe place for spliced fibers to cool after heating.

5.2. Komshine KIP-600V Fiber Inspection Probe Operation

The KIP-600V probe is used to inspect the end-face of fiber optic connectors for dirt, scratches, or other defects that can degrade signal quality.

Figure 5.4: The KIP-600V probe connected to its display unit, showing a fiber end-face for inspection.

5.2.1. Connecting and Powering On

1. Connect the KIP-600V probe to its display unit.
2. Press the power button on the display unit to turn it on.
3. Ensure the battery is sufficiently charged (4000mAh battery provides up to 20 hours of operation).

5.2.2. Inspecting Fiber End-Faces

1. Select the appropriate adapter tip for the fiber connector type (SC, FC, ST, LC, MU, etc.).
2. Insert the fiber connector into the probe tip.
3. Observe the fiber end-face image on the display unit. The KIP-600V provides 400x magnification.
4. Use the focus wheel on the probe to achieve a clear image.
5. Evaluate the end-face cleanliness and quality according to industry standards.

Figure 5.5: The KIP-600V is compatible with SC, FC, ST, LC, and MU connectors, including female versions.

The KIP-600V also supports real-time video recording and TF card expansion for data storage and playback.

6. 유지관리

6.1. Cleaning the FX39 Splicer

• V-그루브 및 Clamps: V자형 홈과 섬유 필터를 정기적으로 청소하십시오.amps with a cotton swab and isopropyl alcohol to remove fiber debris and dust.
• 전극 : Clean the electrode tips with a specialized electrode cleaner or a lint-free swab if they become contaminated. Replace electrodes after approximately 5000 splices or if splice quality degrades.
• 대물렌즈: Gently clean the objective lenses with a lens cleaning solution and a soft, lint-free cloth.
• 화면: Wipe the touch screen with a soft, dry cloth.

6.2. Cleaning the KIP-600V Probe

• 프로브 팁: Ensure the probe tip is clean before each use. Use appropriate fiber cleaning tools for the specific connector type.
• 디스플레이 화면: Clean the display screen with a soft, dry cloth.

6.3. 배터리 관리

• 배터리를 서늘하고 건조한 곳에 보관하십시오.
• 배터리를 자주 완전히 방전시키지 마세요.
• 장기간 보관할 경우 배터리를 약 50~60%까지 충전하십시오.

6.4. 일반 관리

• Always store the equipment in its protective carrying case when not in use.
• Avoid dropping or subjecting the devices to strong impacts. The KIP-600V features a removable silicone case for added protection.

Figure 6.1: The KIP-600V probe with its protective silicone case, designed to reduce damage from impacts.

7. 문제 해결

This section provides solutions to common issues encountered during operation. For problems not listed here, contact customer support.

8. 사양

8.1. Komshine FX39 Fiber Fusion Splicer

• Alignment Method: 6-Motor Core Alignment
• 접합 시간: 약 6초
• 가열 시간 : 약 16초
• 평균 스플라이스 손실: 0.01데시벨
• 전극 수명: Up to 5000 splices
• 배터리 용량: 7800mAh (approx. 400 splice/heat cycles)
• 표시하다: 4.3인치 정전식 터치스크린
• 섬유 홀더: 3-in-1 design
• 냉각: 2-Layer Cooling Tanks
• 무게: 1.72kg (배터리 제외), 2.25kg (배터리 포함)

8.2. Komshine KIP-600V Fiber Inspection Probe

• 확대: 400배
• 디스플레이 화면: 3.5인치
• 배터리 용량: 4000mAh(최대 20시간 작동)
• 해상도 비율 : <1µm
• 호환성: FC/SC/ST/LC/MU/E2000/MPO (with appropriate adapters)
• 특징: Real-time video, TF card support, video playback

9. 보증 및 지원

Komshine products are designed for reliability and performance. For warranty information, please refer to the warranty card included with your product or visit the official Komshine web대지.

For technical support, service, or inquiries, please contact Komshine customer service through the details provided on the product packaging or the official website. When contacting support, please have your product model and serial number available.

온라인 리소스: For additional resources, FAQs, and software updates, please visit the 아마존에서 KOMSHINE 스토어를 만나보세요.