소개
This manual provides comprehensive instructions for the installation, operation, and maintenance of your Avidsen 4-Button 433.92 MHz Rolling Code Remote Control. Please read this manual carefully before use to ensure proper function and safety.
The Avidsen remote control is designed to operate various Avidsen gate and garage door motorizations. It features a 16-bit rolling code technology for enhanced security, generating 65,536 unique combinations for each command. With four independent buttons, it can control up to four different automated systems.
설정 및 프로그래밍
Before using your new remote control, it must be programmed to your Avidsen motorization system. The programming procedure may vary slightly depending on your specific motorization model. Refer to your motorization's instruction manual for detailed programming steps. Generally, the process involves placing your motorization receiver into learning mode and then transmitting a signal from the new remote control.
General Programming Steps (Consult your motorization manual for specifics):
- 수신기에 액세스하십시오. Locate the control unit or receiver on your gate or garage door motorization.
- 학습 모드 활성화: Press and hold the programming button (often labeled "PROG," "LEARN," or similar) on the motorization's receiver. An indicator light (LED) will typically illuminate or flash to confirm learning mode is active.
- 원격에서 전송: While the receiver is in learning mode, press and hold the desired button on your new Avidsen remote control for a few seconds. The receiver's indicator light may change (e.g., flash rapidly, turn solid, or turn off) to confirm successful pairing.
- 학습 모드 종료: Release the programming button on the receiver. Some systems automatically exit learning mode after a short period or after a successful pairing.
- 테스트 작업: Press the programmed button on your remote control to verify that it operates the motorization correctly.
Image: An Avidsen remote control in a hand, sending a signal to open a wooden gate. This illustrates the remote in active use with a gate motorization system.
다중 장치 제어:
This remote features four independent buttons, allowing you to control up to four different Avidsen motorizations (e.g., a gate, a garage door, an additional gate). Repeat the programming steps for each button with its respective motorization.
Image: An Avidsen remote control shown with graphical representations of a swing gate, a garage door, and a sliding gate, indicating its multi-device control capability.
작동 지침
Once programmed, operating your Avidsen remote control is straightforward:
- 활성화: Press the corresponding button on the remote control that has been programmed to your specific gate or garage door motorization.
- 신호 전송 : The remote will send a 433.92 MHz radio signal with a unique 16-bit rolling code to the receiver.
- 범위: Ensure you are within the operational range of your motorization's receiver for reliable signal transmission. Environmental factors can affect range.
- 보안: The rolling code technology ensures that each signal transmitted is unique, preventing unauthorized duplication and enhancing the security of your access points.
유지
배터리 교체:
The remote control is powered by a CR2032 lithium coin cell battery, which is included. The battery typically provides up to 2 years of autonomy, depending on usage frequency. When the remote's range decreases significantly or the indicator light (if present) fails to illuminate, it's time to replace the battery.
- C 열기asing: 리모컨을 조심스럽게 열어보세요asing. There is usually a small notch or screw to facilitate this.
- 오래된 배터리 제거: 기존 CR2032 배터리를 제거할 때 극성(+/-)을 확인하세요.
- 새 배터리를 삽입하세요: 올바른 극성에 맞춰 새 CR2032 배터리를 삽입하세요.
- C 닫기asing: Securely close the remote control casing.
Image: An Avidsen remote control displayed alongside a CR2032 coin cell battery, illustrating the type of battery required for the device.
청소 및 보관:
- 리모컨은 부드럽고 마른 천으로 닦으십시오. 연마성 세제나 용제를 사용하지 마십시오.
- 리모컨은 건조하고, 극한 온도와 직사광선을 피해 보관하십시오.
- The remote is designed for outdoor use and is resistant to water splashes and common weather conditions, but it is not fully submersible.
문제 해결
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| Remote does not operate the motorization. |
|
|
| 작동 범위가 감소했습니다. |
|
|
| Motorization responds intermittently. |
|
|
명세서
- 모델: 114258X2
- 상표: 아비센
- 빈도: 433.92MHz
- 코딩: 16-bit Rolling Code (65,536 combinations)
- 버튼: 4 independent buttons
- 배터리: 1x CR2032 Lithium Coin Cell (included)
- 배터리 수명: Approximately 2 years (depending on usage)
- 치수(길이 x 너비 x 높이): 6.5 x 3.7 x 1cm(2.56 x 1.46 x 0.39인치)
- 무게: 90그램(약 3.17온스)
- 운영 환경: Outdoor use, resistant to water splashes and common weather conditions.
Image: A technical drawing showing the dimensions of the Avidsen remote control: 65 mm in length, 37 mm in width, and 10 mm in thickness.
보증 및 지원
For warranty information, technical support, or assistance with programming, please refer to the documentation provided with your Avidsen motorization system or contact Avidsen customer service directly. Keep your proof of purchase for warranty claims.
제조업체: 아비센
Web대지: www.avidsen.com
