TURBRO Greenland 12,000 BTU 덕트리스 미니 스플릿 인버터 에어컨 (히트펌프 포함) 사용 설명서

1. 서론

This manual provides essential information for the safe and efficient installation, operation, and maintenance of your TURBRO Greenland 12,000 BTU Ductless Mini Split Inverter AC with Heat Pump. Please read this manual thoroughly before installation and use, and retain it for future reference.

주요 특징:

• Powerful Heating and Cooling: Utilizes inverter technology for efficient operation in extreme temperatures, cooling up to 131°F and heating down to -13°F. Achieves fast cooling in 30 seconds and heating in 60 seconds.
• 에너지 효율성: Features a 23 SEER2 rating, ensuring lower electricity consumption and potential eligibility for federal tax credits.
• 조용한 작동: Designed for low noise levels, with a minimum noise level of 27 decibels.
• Long Distance Air Blowing: A large drum-shaped impeller fan provides efficient air circulation across areas up to 750 sq.ft.
• WiFi-Enabled Control: Allows convenient control via a smartphone application.
• 제습기 기능: Includes a built-in dehumidifier for improved air quality.

2. 상자 안에 무엇이 들어있나요?

Your TURBRO Greenland Mini Split system is typically delivered in two separate boxes. Please verify all packages upon delivery to ensure all components are received before scheduling installation or beginning the installation process.

Figure 1: TURBRO Greenland Mini Split system components.

Box One (Indoor Unit & Accessories):

• 실내기
• 사용자 설명서
• 신호 케이블
• Remote & AAA Battery
• 드레인 조인트
• 리모콘 홀더
• 나사
• 장착 플레이트
• 고무 발
• 가이드 플레이트
• Drain Hose (for indoor unit)

Box Two (Outdoor Unit & Installation Kit):

• 실외기
• Drain Hose (for outdoor unit)
• Refrigerant Pipe (16.4 ft.)
• 벽면 슬리브
• 절연 테이프
• 밀봉 껌

3. 설정 및 설치

The TURBRO Greenland Mini Split AC is designed for easy installation with a step-by-step guide and numbered wiring diagram. However, professional installation is recommended to ensure optimal performance and safety.

3.1 실내기 설치

1. Mounting Plate Placement: Use the provided cardboard template to mark the position for the indoor unit's mounting plate on the wall. Ensure adequate clearance: approximately 8 inches from the ceiling and 14 inches from adjacent walls. Use a level to ensure proper alignment.
2. 구멍 뚫기: Drill pilot holes for the mounting plate screws. For brick or concrete walls, use appropriate masonry drill bits and anchors. For drywall, locate studs or use heavy-duty drywall anchors rated for the unit's weight.
3. 안전한 장착 플레이트: Attach the mounting plate securely to the wall using the appropriate screws.
4. Drill Conduit Hole: Drill a large hole (typically 2.5-3 inches in diameter) through the wall for the refrigerant lines, drain hose, and electrical cables. Ensure this hole is angled slightly downwards towards the exterior to facilitate drainage.
5. Electrical Wiring (Indoor Unit): Open the front panel of the indoor unit. Locate the electrical terminal block. Connect the power wires from the outdoor unit to the corresponding terminals (L, N, 1, 2, 3, Ground) as indicated in the wiring diagram. Secure the wires with the cable clamp.
6. Wrap Lines: Bundle the refrigerant lines, electrical cable, and drain hose together using insulation tape. This protects them and facilitates passage through the wall.
7. 실내기 설치: Carefully feed the bundled lines through the wall hole. Lift the indoor unit and hook it onto the top of the mounting plate, then gently push the bottom until it snaps into place. Ensure the unit is level and securely attached.

3.2 실외기 설치 위치

1. 사이트 선택: Choose a suitable, level location for the outdoor unit. Ensure at least 12 inches of clearance from the back of the unit to any wall and 20 inches on either side for proper airflow and maintenance.
2. Install Rubber Feet: Attach the provided rubber feet to the base of the outdoor unit. These help reduce vibration and noise.
3. Electrical Wiring (Outdoor Unit): Open the wiring cover on the outdoor unit. Connect the electrical wires from the indoor unit and the main power supply to the corresponding terminals (L, N, 1, 2, 3, Ground) as per the wiring diagram. Use liquid-tight conduit for the main power supply for safety and weather protection.
4. 냉매 라인 연결: Carefully bend the pre-charged refrigerant lines from the indoor unit to align with the outdoor unit's service ports. Remove protective caps and hand-tighten the flare nuts. Use two wrenches to tighten them to the specified torque.
5. 배수 호스를 연결하세요: Connect the outdoor unit's drain hose to the designated port.

3.3 시스템 시운전

1. 시스템 진공 청소: Connect a vacuum pump and gauge set to the low-pressure service port. Run the vacuum pump for at least 15 minutes to remove air and moisture from the refrigerant lines. Close the low-pressure port and monitor the gauge for at least 15 minutes to ensure no leaks are present (the reading should remain at -0.1 MPa).
2. Release Refrigerant: If the system holds a vacuum, release a small amount of refrigerant into the lines for a leak check. Open the low-pressure valve for 5 seconds, then close it. Apply soapy water to all connections; if bubbles appear, there is a leak that needs to be addressed.
3. Fully Open Valves: If no leaks are detected, fully open both the low and high-pressure valves to release the refrigerant into the system. Replace all protective caps.
4. 전원 켜기: Turn on the dedicated 20-amp circuit breaker in your electrical panel. Your AC unit is now ready for operation.

4. 사용 설명서

Your TURBRO Greenland Mini Split offers various operating modes and convenient control options.

4.1 제어 옵션

• 원격 제어: Use the included remote control to adjust settings, change modes, and set timers.
• WiFi-Enabled App: Download the dedicated smartphone app to control your unit remotely. This allows you to adjust settings from anywhere.

4.2 작동 모드

• 쿨 모드 : Provides powerful cooling, quickly lowering room temperature.
• 가열 모드: Offers efficient heating, even in cold outdoor conditions.
• 제습기 모드: Reduces humidity levels in the room for increased comfort.
• 팬 모드: 가열이나 냉각 없이 공기를 순환시킵니다.

5. 유지관리

정기적인 유지관리를 통해 장비의 최적의 성능과 수명을 보장할 수 있습니다.

5.1 필터 청소

The indoor unit's air filters are easily accessible for cleaning:

1. 실내기 전면 패널을 조심스럽게 여세요.
2. 공기 필터를 제거하세요.
3. Clean the filters using a vacuum cleaner or by washing them with lukewarm water.
4. 필터를 다시 삽입하기 전에 완전히 건조시키십시오.
5. 전면 패널을 단단히 닫으십시오.

6. 문제 해결

If you encounter issues with your unit, refer to the following common troubleshooting steps. For persistent problems, contact customer support.

• 장치가 켜지지 않음: Check the power supply and ensure the circuit breaker is ON. Verify all electrical connections are secure.
• 냉방/난방이 충분하지 않음: Ensure air filters are clean. Check for obstructions around indoor and outdoor units. Verify correct mode and temperature settings.
• 비정상적인 소음: Minor noises during operation are normal. Excessive or unusual noises may indicate an issue; consult the full user manual or customer support.
• 누수: Check if the drain hose is properly installed, free of kinks, and not clogged.

7. 사양

8. 보증 및 지원

8.1 보증 정보

The TURBRO Greenland Mini Split Inverter AC comes with a 24-month warranty. Please refer to the full warranty details in the included User Manual for terms and conditions.

8.2 고객 지원

For technical assistance, troubleshooting, or warranty claims, please contact TURBRO Customer Support. Contact information can be found in your User Manual or on the official TURBRO web대지.