1. 서론
This manual provides essential information for the safe and efficient operation of your GEPRC Vapor-X5 HD O4 Pro FPV Drone. Please read this manual thoroughly before using the product to ensure proper setup, flight, and maintenance.
The Vapor-X5 HD O4 Pro is a high-performance FPV drone designed for immersive flight experiences and high-definition video capture. It features a robust frame, powerful motors, and advanced flight control systems, including GPS for enhanced stability and navigation.
Image: The GEPRC Vapor-X5 HD O4 Pro FPV Drone, showcasing its design and propellers.
2. 안전 지침
- 지역 규정: Always check and comply with local drone regulations and laws before flying. This drone weighs 409g, which typically requires registration and adherence to specific flight rules in many regions.
- 비행 전 점검: Before each flight, inspect the drone for any damage, ensure propellers are securely attached, and verify battery levels.
- 환경 조건: Avoid flying in strong winds, rain, fog, or other adverse weather conditions.
- 시선: Maintain visual line of sight with your drone at all times.
- 장애물: Fly in open areas, away from people, buildings, trees, and power lines.
- 배터리 안전: Use only recommended batteries and follow proper charging and storage procedures.
- 프로펠러 안전: 회전하는 프로펠러에 손과 얼굴이 닿지 않도록 주의하세요.
3. 패키지 내용
아래 나열된 모든 품목이 패키지에 포함되어 있는지 확인하세요.
포함 항목:
- 1 x Vapor-X5 O4 Pro Drone
- 2 x GEMFAN 5136 Propellers
- 배터리 미끄럼 방지 패드 2개
- 1 x Spare screw pack
- 증기 측면 패널 1개
- M20*250mm 배터리 스트랩 2개
- 1 x L자형 드라이버 1.5mm
- 1 x L자형 드라이버 2.0mm
- GoPro 마운트 1개
Spare Screw Pack Includes:
- 6 x M3*10mm round head screws
- 6 x M3*8mm round head screws
- 2 x M3*6mm flat head screws
- 1 x M5*28mm thin head screw
- 1 x M5 flange nut
- 4 x M3 rivet nuts
4. 설정
4.1. Receiver Installation and Binding (PNP Version)
As a Plug-N-Play (PNP) version, the GEPRC Vapor-X5 O4 Pro does not include a pre-installed receiver. You will need to install a compatible receiver (e.g., GEPRC ELRS24 or TBS Nano RX) and bind it with your remote controller. Refer to your chosen receiver's manual for specific installation and binding instructions.
4.2. Camera and VTX Module Installation
The O4 Pro Camera and VTX module require careful installation to ensure optimal performance and vibration dampening. Follow these general steps, referring to the provided video for visual guidance:
- Insert the O4 camera into its camera bracket, ensuring the connector faces the canopy.
- Install the shock-absorbing balls into the camera bracket slots.
- Place the camera and bracket assembly into the canopy, aligning the holes. Secure with M2*4 flat head socket cap screws.
- Install the VTX shock absorption module. Insert the 6.6mm shock-absorbing balls into the module's holes, ensuring the higher end faces down.
- Connect the 6Pin connector cable to the O4 VTX module and the VTX antenna to its connector.
- Place the O4 VTX module onto the flight controller, aligning the holes with the flight control unit.
- Tighten the forward shock-absorbing ball of the O4 VTX module with an M1.4*10*4 Phillips flat washer head tapping screw.
- Place the canopy onto the O4 VTX module, ensuring the camera faces forward and the canopy holes align with the shock-absorbing balls.
- Pass the VTX antenna through the rear hole of the canopy.
- Tighten the canopy with three M1.4*10*4 Phillips flat washer head tapping screws.
- Replace the camera cable using tweezers, ensuring it is suspended to reduce vibration and prevent touching the canopy.
Video: Detailed installation guide for the Meteor65 Pro/Meteor75 Pro Brushless Drone, demonstrating camera and VTX module setup. This process is similar for the Vapor-X5 O4 Pro.
Video: Installation steps for the Pavo Femto Quadcopter, showing how to integrate the DJI O4 Air Unit. This provides additional visual reference for similar drone assembly.
4.3. 배터리 설치
Securely attach the recommended 6S LiPo 1300mAh – 1800mAh battery to the top plate using the provided battery straps. Ensure the battery is centered for optimal balance and that the anti-slip pads prevent movement during flight. Connect the XT60 connector to the drone's power port.
5. 사용 설명서
5.1. 비행 전 체크리스트
- Ensure all components (drone, remote controller, FPV goggles) are fully charged.
- Verify propellers are correctly installed and free from damage.
- Check for any loose screws or connections.
- Confirm GPS signal acquisition before takeoff (drone will beep when satellites are acquired).
- Perform a quick visual inspection of the flight area for any potential hazards.
5.2. 비행 모드 및 제어
The Vapor-X5 O4 Pro supports various flight modes. Familiarize yourself with your remote controller's manual for specific mode activation and control schemes. For FPV flight, ensure your goggles are properly configured and displaying a clear video feed.
Video: Demonstrates First-Person View (FPV) immersion with a Walksnail FPV System, providing a visual example of the FPV experience.
5.3. GPS 기능
The integrated GEP-M10 GPS module provides enhanced stability and safety features. Ensure GPS lock is achieved before takeoff. Key GPS features include:
- 위치 유지: Maintains the drone's position automatically.
- 귀가(RTH): Automatically flies the drone back to its takeoff point in case of signal loss or low battery.
It is mandatory to configure and test GPS failsafe settings in your flight controller software (e.g., Betaflight) to ensure safe operation in case of signal loss.
5.4. Video Recording and Photography
The O4 Pro Camera captures high-definition video and still images. Refer to your FPV system's documentation for instructions on how to start/stop recording and capture photos. The drone features 46GB of internal storage for recorded footage.
6. 유지관리
6.1. 청소
Regularly clean your drone to remove dust, dirt, and debris. Use a soft, dry cloth for the frame and components. For the camera lens, use a specialized lens cleaning cloth and solution.
6.2. 프로펠러 교체
Inspect propellers for cracks, bends, or chips before each flight. Damaged propellers can lead to unstable flight and potential crashes. To replace:
- 드론의 전원을 끄고 배터리를 분리하세요.
- Carefully remove the damaged propeller by unscrewing the M5 flange nut.
- Install a new GEMFAN 5136 propeller, ensuring it is oriented correctly (clockwise or counter-clockwise as indicated on the motor/propeller).
- Secure with the M5 flange nut, ensuring it is tight but not overtightened.
6.3. 배터리 관리
- 충전 중: Use only a compatible LiPo charger. Never leave charging batteries unattended.
- 저장: 리튬 폴리머 배터리는 적절한 보관 부피에 보관하십시오.tage (typically 3.8V per cell) in a fire-safe bag or container.
- 처분: 손상되었거나 부풀어 오른 배터리는 현지 규정에 따라 안전하게 폐기하십시오.
6.4. 펌웨어 업데이트
Periodically check the GEPRC official website for firmware updates for your drone's flight controller (GEP-F722-HD v2) and O4 Air Unit Pro. Keeping firmware updated ensures optimal performance, new features, and bug fixes.
7. 문제 해결
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| 드론의 전원이 켜지지 않습니다. | Battery not connected, battery depleted, faulty power cable. | Ensure battery is fully charged and correctly connected. Check XT60 connector for damage. |
| Loss of video signal in FPV goggles. | VTX/antenna issue, interference, out of range. | Check VTX antenna connection. Ensure you are within operating range. Avoid areas with high interference. |
| 불안정한 비행 또는 표류. | Damaged propellers, uncalibrated sensors, strong winds. | Inspect and replace damaged propellers. Calibrate accelerometers/gyroscopes in Betaflight. Avoid flying in strong winds. |
| GPS 신호가 잡히지 않습니다. | Poor satellite visibility, interference, GPS module issue. | Ensure drone has a clear view of the sky. Avoid flying near tall buildings or dense foliage. Check GPS module connection. |
8. 사양
| 요소 | 사양 |
|---|---|
| 모델 | Vapor-X5 O4 Pro |
| 액자 | GEP-Vapor-X5 O4 Pro frame |
| 휠베이스 | 230mm (XNUMXmm) |
| 상판 | 2.0mm (XNUMXmm) |
| 중간 플레이트 | 2.0mm (XNUMXmm) |
| 바텀 플레이트 | 2.5mm (XNUMXmm) |
| 팔 두께 | 5.0mm (XNUMXmm) |
| FC | GEP-F722-HD v2 (MCU: STM32F722, Gyro: ICM42688-P(SPI), Barometer: YES, OSD: Betaflight OSD w/AT7456E) |
| 키보드 | 테이커 H60_BLS 60A 4IN1 ESC |
| 비티엑스 | O4 에어 유닛 프로 |
| 카메라 | O4 프로 카메라 |
| 안테나 | O4 Pro 정품 안테나 |
| 커넥터 | 엑스티60 |
| 옵션 GPS | GEP-M10 GPS |
| 5인치 모터 | GEPRC SPEEDDX2 2207E 1960kV |
| 5인치 프로펠러 | 젬판 5136 |
| 무게 (PNP 버전) | 409g ± 5g |
| 수화기 | PNP/GEPRC ELRS24/TBS Nano RX (User-supplied for PNP) |
| 추천 배터리 | 6S 리튬 폴리머 1300mAh – 1800mAh |
| 비행 시간 | 14-19분 |
| 비디오 캡처 해상도 | 4K |
| 내부 저장소 | 46GB (XNUMX기가바이트) |
9. 보증 및 지원
For warranty information, technical support, or service inquiries, please refer to the official GEPRC web사이트를 방문하거나 공인 대리점에 문의하세요. 보증 청구를 위해 구매 증빙 자료를 보관하세요.
