소개
Welcome to the XPG INVADER X MINI ATX Mid Tower PC Case instruction manual. This guide provides detailed information on the installation, operation, and maintenance of your new PC case. The INVADER X MINI is designed for compact, stylish, and powerful gaming rig builds, offering impressive compatibility with ATX motherboards and optimal airflow with five pre-installed ARGB fans.
Please read this manual thoroughly before beginning assembly to ensure proper installation and safe operation.
패키지 내용
패키지에 모든 구성 요소가 들어 있는지 확인하세요.
- XPG INVADER X MINI PC Case
- 부속품 상자 (나사, 케이블 타이, 스탠드오프 등)
- 사용 설명서 (본 문서)
안전 예방 조치
- 구성 요소를 설치하거나 제거하기 전에 항상 벽면 콘센트에서 전원 공급 장치를 분리하세요.
- 손상을 방지하기 위해 구성품을 조심스럽게 다루십시오.
- 정전기 방전(ESD)으로 인한 민감한 부품 손상을 방지하기 위해 정전기 방지 손목 스트랩을 착용하십시오.
- 작은 부품과 나사는 어린이의 손이 닿지 않는 곳에 보관하십시오.
설정 및 설치
1. 사건 준비
Carefully remove the case from its packaging. Place it on a stable, flat surface. Remove the side panels by unscrewing the thumb screws at the rear of the case and sliding the panels off.
이미지: 앞면 view of the XPG INVADER X MINI PC case, showcasing its tempered glass panels and the vibrant ARGB fans. This view highlights the compact elegance and panoramic design.
2. 마더보드 설치
- 케이스 내부에서 마더보드 트레이 개구부에 I/O 실드를 설치합니다.
- Align your ATX motherboard with the pre-installed standoffs. Ensure the screw holes on the motherboard match the standoffs.
- 제공된 나사를 사용하여 마더보드를 고정합니다.
이미지: 내부 view of the PC case, illustrating the spacious motherboard tray and various mounting points for components. This image helps visualize the layout for component installation.
3. 전원 공급 장치(PSU) 설치
The INVADER X MINI supports rear-mount power supplies. Slide your PSU into the designated compartment at the rear bottom of the case and secure it with screws from the outside.
Image: Rear internal view of the PC case, highlighting the power supply mounting area and cable routing channels behind the motherboard tray. This demonstrates the design for clean cable management.
4. 저장 드라이브 설치
Install 2.5" SSDs or 3.5" HDDs into the designated drive bays. Refer to the accessory box for specific mounting hardware.
이미지: 상세 내부 구조 view of the PC case, focusing on the drive bays and fan mounting locations. This helps users identify where to install storage devices and additional cooling.
5. 그래픽 카드(GPU) 및 확장 카드 설치
케이스 후면에서 필요한 PCIe 슬롯 커버를 제거합니다. 그래픽 카드 또는 기타 확장 카드를 마더보드의 PCIe 슬롯에 삽입하고 나사로 고정합니다.
Image: Rear exterior view of the PC case, showing the PCIe expansion slots, the rear exhaust fan, and the I/O panel cutout. This view is crucial for installing expansion cards and connecting peripherals.
6. 케이블 관리
메인보드 트레이 뒤쪽의 케이블 정리용 홈과 고정 지점을 활용하여 케이블을 깔끔하게 정리하세요. 이렇게 하면 공기 흐름이 개선되고 미관도 향상됩니다.
Image: Side internal view of the PC case, illustrating the pre-installed ARGB fans and the internal layout for component placement. This perspective helps in planning component installation and cable routing.
7. 전면 패널 I/O 연결
Connect the front panel cables (USB, audio, power switch, reset switch, LED indicators) to the corresponding headers on your motherboard. Refer to your motherboard manual for exact pin layouts.
Image: Top-down internal view of the PC case, showing the top fan mounts and the overall internal structure. This view is useful for understanding top-mounted radiator or fan installations.
PC 케이스 작동 방법
전원 켜기
Once all components are installed and cables are connected, replace the side panels. Connect your monitor, keyboard, mouse, and power cable to the PC. Press the power button on the front panel of the case to turn on your system.
ARGB 팬 컨트롤
The XPG INVADER X MINI comes with five pre-installed ARGB fans. These fans can be controlled via your motherboard's ARGB software (if compatible) or a dedicated ARGB controller (if included or purchased separately). Refer to your motherboard manual or ARGB controller instructions for specific lighting effects and synchronization.
유지
먼지 필터 청소
The case is equipped with dust filters to prevent dust buildup inside. Regularly clean these filters (typically located at the top, front, and bottom) by removing them and gently brushing or washing them with water. Ensure they are completely dry before re-installing.
일반 청소
부드러운 d를 사용하세요amp cloth to wipe down the exterior of the case. Avoid abrasive cleaners or solvents that may damage the finish or tempered glass panels.
문제 해결
- 시스템 전원이 켜지지 않음: Ensure all power cables (24-pin ATX, 8-pin CPU, GPU power) are securely connected. Check the power switch connection to the motherboard. Verify the PSU is switched on.
- 팬이 회전하지 않거나 ARGB 조명이 켜지지 않음: Check fan power connections to the motherboard or fan controller. Ensure ARGB headers are correctly connected and software is configured.
- 디스플레이 출력 없음: Confirm the graphics card is properly seated in its PCIe slot and has adequate power. Ensure the monitor cable is connected to the graphics card, not the motherboard's integrated graphics ports (unless using integrated graphics).
- 과열: Verify all fans are spinning correctly and are oriented for optimal airflow (intake/exhaust). Ensure CPU cooler and GPU fans are functioning. Clean dust filters.
명세서
| 특징 | 사양 |
|---|---|
| 상표 | 엑스피지(XPG) |
| 시리즈 | INVADER X MINI |
| 모델 번호 | CJ11533856 |
| 케이스 유형 | 미드 타워 |
| 마더보드 호환성 | 에이티엑스 |
| 치수(길이x너비x높이) | 14.13 x 8.27 x 18.11 인치 |
| 품목 무게 | 12.54파운드(5.7킬로그램) |
| 색상 | 검은색 |
| 재료 | 플라스틱, 강화 유리 |
| 사전 설치된 팬 | ARGB 팬 5개 |
| 냉각 방식 | 공기 |
| 전원 공급 장치 장착 유형 | 후면 마운트 |
보증 및 지원
XPG products are designed and manufactured to the highest quality standards. For information regarding warranty coverage, please refer to the warranty card included with your product or visit the official XPG web대지.
For technical support, troubleshooting assistance, or to inquire about replacement parts, please contact XPG customer service through their official web사이트 또는 제품 설명서에 제공된 연락처 정보를 참조하세요.
Please have your product model number (INVADER X MINI) and serial number ready when contacting support.
