그라코 4Ever DLX 슬림 4-in-1 카시트 사용 설명서

소개

This manual provides essential instructions for the safe and proper use, installation, and maintenance of your Graco 4Ever DLX Slim 4-in-1 Car Seat. This car seat is designed to adapt to your child's growth, offering four distinct modes of use from infancy through toddlerhood and beyond.

Figure 1: The Graco 4Ever DLX Slim car seat transitions through four modes: rear-facing harness (4-40 lb), forward-facing harness (26.5-65 lb), highback booster (40-100 lb), and backless booster (40-120 lb).

안전 정보

Always read and understand all instructions and warnings before using this car seat. Failure to follow these instructions could result in serious injury or death to your child.

• 어린이 체중 및 신장 제한: Adhere strictly to the weight and height limits for each mode of use as specified in the "Specifications" section.
• 차량 호환성: Ensure your vehicle's seating position is suitable for car seat installation. Consult your vehicle owner's manual.
• Harness and Belt Usage: Always secure your child properly in the harness or vehicle seat belt. The harness straps must be snug, and the chest clip positioned at armpit level.
• 제품 수명: Do not use the car seat beyond its expiration date, typically found on the car seat label.
• Crash Involvement: A car seat involved in a moderate to severe crash should be replaced immediately, even if there is no visible damage.

Figure 2: The Graco 4Ever DLX Slim is Graco ProtectPlus Engineered, meeting rigorous crash testing standards for comprehensive protection.

설정 및 설치

Proper installation is crucial for child safety. This car seat features SnugLock technology and InRight LATCH for simplified installation.

1. Rear-Facing Harness Mode (4-40 lb)

For infants and small children, rear-facing is the safest option. Position the car seat in the rear-facing orientation in your vehicle's back seat.

1. Place the car seat on the vehicle seat with the recline handle fully extended for the rear-facing position.
2. Route the vehicle's lap and shoulder belt through the designated rear-facing belt path, or attach the lower anchor connectors (LATCH) to your vehicle's lower anchors.
3. Engage the SnugLock arm to tighten the vehicle belt or LATCH strap, ensuring a secure fit. The car seat should not move more than one inch side-to-side or front-to-back at the belt path.
4. Adjust the 6-position recline to achieve the correct recline angle for your child, indicated by the level indicator on the side of the car seat.

2. Forward-Facing Harness Mode (26.5-65 lb)

Once your child meets the minimum weight and height requirements for forward-facing, and has outgrown the rear-facing limits, you can transition to this mode.

1. Position the car seat in the forward-facing orientation on the vehicle seat.
2. Route the vehicle's lap and shoulder belt through the designated forward-facing belt path, or attach the lower anchor connectors (LATCH) to your vehicle's lower anchors.
3. Attach the top tether strap to the vehicle's top tether anchor point and tighten.
4. Engage the SnugLock arm to tighten the vehicle belt or LATCH strap, ensuring a secure fit.

3. Highback Booster Mode (40-100 lb)

For older children who have outgrown the harness but still require back support and proper belt positioning.

1. Remove the car seat harness system and store it according to the manual.
2. Place the highback booster on the vehicle seat.
3. Guide the vehicle's lap and shoulder belt through the designated belt guides on the booster and across your child.

4. Backless Booster Mode (40-120 lb)

For children who are ready for a backless booster, providing proper vehicle seat belt fit.

1. Remove the highback portion of the booster.
2. Place the backless booster on the vehicle seat.
3. Guide the vehicle's lap and shoulder belt through the designated belt guides on the booster and across your child.

Figure 3: The SnugLock technology simplifies installation, allowing for a secure fit using either the vehicle seat belt or LATCH system.

Figure 4: The slim design of the 4Ever DLX Slim car seat helps optimize backseat space.

작동 지침

Harness Adjustment (No-Rethread Simply Safe Adjust)

The No-Rethread Simply Safe Adjust Harness System allows for simultaneous adjustment of the headrest and harness height. This ensures a proper fit as your child grows without the need to rethread the harness straps.

1. Locate the harness adjustment handle, typically at the top of the headrest.
2. Squeeze the handle and slide the headrest up or down until the harness straps are at or just below your child's shoulders for rear-facing, or at or just above your child's shoulders for forward-facing.
3. Release the handle to lock the headrest and harness in place.

아동 위탁 및 보호

1. 아이를 카시트에 앉히세요.
2. 안전벨트 끈을 아이의 어깨 위로 넘겨 가랑이 버클을 채우세요.
3. 가슴 클립을 겨드랑이 높이에 연결하세요.
4. Pull the harness tightening strap until the harness is snug against your child's body. You should not be able to pinch any excess web어깨에 빙.

Figure 5: Fuss-free harness storage keeps straps out of the way when placing or removing your child.

유지

청소 지침

The Rapid Remove cover is designed for easy cleaning without uninstalling the car seat.

• 좌석 패드: Machine wash the seat pad in cold water on a delicate cycle. Drip dry. Do not use bleach.
• 하네스 스트랩: 하네스 스트랩을 광고용 천으로 닦으세요amp 천 소재입니다. 세탁기에 넣거나 물에 담그지 마십시오. 끈이 약해질 수 있습니다.
• 버클: 버클을 광고로 닦으세요amp cloth. If the buckle is sticky, rinse it under warm water without detergents.
• 플라스틱 및 금속 부품: Wipe with mild soap and cool water.

Figure 6: The Rapid Remove cover allows for quick and easy cleaning.

저장

When not in use, store the car seat in a cool, dry place away from direct sunlight. Ensure all components, especially the harness and LATCH connectors, are properly stored within the designated compartments to prevent loss or damage.

문제 해결

If you encounter issues with your car seat, refer to the following common solutions. For more complex problems, consult the full product manual or contact Graco customer support.

• 안전벨트 조임이 어렵습니다. Ensure the harness straps are not twisted and are routed correctly through the seat back. Check that the chest clip is unbuckled before tightening.
• 느슨한 설치: Re-check the installation steps for your chosen mode (rear-facing, forward-facing). Ensure the SnugLock arm is fully engaged and the vehicle belt or LATCH strap is pulled taut. Verify the car seat does not move more than one inch at the belt path.
• Recline Adjustment Issues: Ensure the car seat is not under tension from the vehicle seat belt or LATCH system when attempting to adjust the recline.

명세서

그림 7: 이상view of the Graco 4Ever DLX Slim car seat's main features.

보증 및 지원

Graco provides a limited warranty for its products. For specific warranty details, registration, or to contact customer support, please visit the official Graco web자세한 내용은 웹사이트를 참조하거나 구매 시 동봉된 보증 카드를 확인하십시오. 보증 청구를 위해 구매 증빙 자료를 보관하십시오.

Graco Customer Service: 도움이 필요하면 방문하세요. GracoBaby.com/support 또는 고객 서비스 센터에 문의하십시오.