INGQI Trimmer Head Replacement Instruction Manual

1. 안전 정보

Before installing or operating the trimmer head, please read and understand all safety instructions. Failure to follow these instructions may result in serious injury.

• Always wear appropriate personal protective equipment (PPE), including safety glasses, gloves, long pants, and sturdy footwear, when working with string trimmers.
• Ensure the string trimmer's engine is off and the spark plug wire is disconnected before performing any installation, maintenance, or inspection.
• Keep hands, feet, and clothing away from the rotating trimmer head.
• Inspect the trimmer head for damage before each use. Do not use if damaged.
• Use only the recommended trimmer line size and type for your string trimmer and this head.
• 주변 사람들, 특히 어린이와 애완동물은 수술 구역에서 안전한 거리(최소 50피트/15m)를 유지하세요.

2. 제품 오버view

This INGQI Trimmer Head is designed as a replacement part for various string trimmer models, offering reliable performance for your lawn and garden maintenance tasks.

2.1 패키지 내용

• 1 x Trimmer Head (includes 1 x Roller, 1 x Hinge Pin, 1 x E-Ring Clip)

2.2 호환성

This trimmer head is compatible with a wide range of string trimmers. Please verify your specific model number against the list below:

• For Homelite String Trimmers: BCH20, BCH24, BCH32, BCH33, BCH40, BCH48, HBC20, HBC24, HBC32C, HBC33, HBC30, HBC38, HK15, HK18 (after 1/1/86), HK28, HK24 (after 1/1/86), HK25, HK30 (up to 1/86), HK33 (after 1/1/86), HK38, PBC3600, PBC3800, PBC4000, PLT3400, ST100, ST120, ST155, ST200, ST360, ST80, ST285, ST155, ST175, ST385, ST485, FK514, NBA524, PMB522, ST100, ST200, ST400, SXD20, RK521, TK518.
• For ECHO String Trimmers: GT200, GT225, GT225i, GT225L, GT225SF, GT230, GT251, GT100, GT140, GT160, GT1000, GT1100, GT2000, GT2100, GT2101, GT2102, GT2103, GT2200, GT2301, GT2400, PAS210, PAS211, PAS225, PAS225VP, PAS225VPB, PAS230, PAS231, PAS260, PAS261, PAS265, PAS266, PAS280, PAS2100, PAS2400, PAS2601, SRM 210, SRM 225, SRM 200, SRM 230, SRM 250, SRM 265, SRM 266, SRM 280, SRM 2100, SRM 2400, SRM140, SRM200, SRM202, SRM210, SRM230, SRM250, SRM251, SRM260, SRM261, SRM265, SRM266, SRM266S, SRM266T, SRM266U.
• For RedMax String Trimmers: BC220DL, BC221DL, BC300DL, BC2300DL, BK235FL, BK345FL, BK435FL, BK530DL, BC17, BC23.
• For Shiandaiwa String Trimmers: T195S, T220, T222, T230, T230s, T231, T242, T242X, T2510, T2510X, 22T, C230, C242, C2510.

그림 1: 측면 view of the INGQI Trimmer Head Replacement with pre-installed trimmer line.

3. 설치 지침

Follow these steps to replace your old trimmer head with the new INGQI Trimmer Head. Always refer to your string trimmer's original manual for specific instructions if available.

3.1 필요한 도구

• Wrench (size may vary depending on your trimmer's shaft bolt)
• 장갑

3.2 단계별 설치

1. 트리머를 준비하세요: Ensure the string trimmer is turned off, the engine is cool, and the spark plug wire is disconnected to prevent accidental starting.
2. 기존 트리머 헤드를 제거하세요: Locate the bolt or nut securing the old trimmer head to the trimmer shaft. Use a wrench to loosen and remove it. Some trimmers may have a locking pin to hold the shaft still while loosening. Turn the bolt/nut in the direction indicated by your trimmer's manual (often reverse thread).
3. 깨끗한 샤프트: Clean any debris or grass buildup from the trimmer shaft threads.
4. 새 트리머 헤드를 설치하세요: Align the new INGQI Trimmer Head with the trimmer shaft. The head typically screws onto the shaft. Ensure it is seated correctly.
5. 머리를 단단히 고정하십시오: Tighten the bolt or nut firmly. Do not overtighten, as this can damage the threads.
6. 설치 확인: Gently tug on the trimmer head to ensure it is securely attached and does not wobble. Reconnect the spark plug wire.

그림 2: 상향식 view of the trimmer head, showing the central mounting point.

그림 3: 경사진 상단 view of the trimmer head, illustrating its compact design.

4. 사용 설명서

Once the trimmer head is securely installed, you can operate your string trimmer as usual. Always follow your trimmer's manufacturer guidelines for safe operation.

4.1 일반 작업

• Start the trimmer engine according to its instructions.
• 두 손으로 트리머를 단단히 잡으세요.
• Maintain a balanced stance and keep the trimmer head away from your body.
• Cut grass by swinging the trimmer head from side to side, using the tip of the line.

4.2 Line Feeding

This trimmer head typically uses a bump-feed mechanism. To advance the trimmer line:

1. While the trimmer engine is running at full throttle, lightly tap the bottom of the trimmer head on a firm, flat surface (e.g., the ground).
2. The impact will release a small amount of line. The trimmer's line-cutting blade (if equipped) will trim the line to the correct length.
3. Repeat as necessary when the line becomes too short.

Figure 4: The trimmer head in use on a string trimmer, demonstrating its function during grass trimming.

5. 유지관리

정기적인 유지 관리는 트리머 헤드의 수명과 최적의 성능을 보장합니다.

5.1 Replacing Trimmer Line

When the trimmer line runs out, it needs to be replaced. This head is designed for easy line reloading.

1. Turn Off Trimmer: 트리머가 꺼져 있고 점화 플러그 배선이 분리되어 있는지 확인하십시오.
2. Remove Old Line (if any): If there are short pieces of line remaining, pull them out.
3. Align Head: Look for arrows or indicators on the trimmer head and align them. This typically aligns the internal spool with the line exit holes.
4. Insert New Line: Take a length of new trimmer line (refer to your trimmer's manual for recommended diameter and length). Push one end of the line through one of the line exit holes and continue pushing it through the head until it comes out the opposite exit hole.
5. Equalize Line: Pull the line through until an equal length extends from both sides of the trimmer head.
6. 풍향선: Rotate the bump knob or the top of the trimmer head in the direction indicated by an arrow (usually clockwise) to wind the line into the spool. Keep winding until only about 6-8 inches of line extend from each side.
7. 확인하다: Ensure the line is securely wound and both ends are extended.

그림 5: 클로즈업 view of the trimmer head's side, highlighting the line exit points and the internal mechanism for line feeding.

5.2 청소 및 보관

• After each use, clean the trimmer head to remove grass clippings, dirt, and debris. This prevents buildup that can hinder performance.
• Use a stiff brush or cloth. Avoid using harsh chemicals that could damage the plastic.
• 트리머 헤드는 직사광선과 극한 온도 변화를 피해 깨끗하고 건조한 곳에 보관하십시오.

6. 문제 해결

If you encounter issues with your trimmer head, refer to the following common problems and solutions:

• 줄이 공급되지 않음:
  • Check if the line is tangled or jammed inside the spool.
  • Ensure the line is not fused together due to heat. Rewind the line if necessary.
  • Verify that the line is of the correct diameter and type for the head.
• Trimmer Head Not Spinning:
  • Ensure the trimmer head is securely attached to the shaft.
  • Check for any obstructions (e.g., thick grass, debris) preventing rotation.
  • Inspect the trimmer's drive shaft and clutch for issues (refer to your trimmer's manual).
• 과도한 진동:
  • Ensure the trimmer line is evenly distributed and cut to equal lengths on both sides.
  • Check if the trimmer head is properly balanced and securely mounted.

7. 사양

• Part Numbers Replaced: 99944200907, 99944200902, 78890-30000, 78890-11000, 78890-18001
• 재료: 내구성이 뛰어난 플라스틱 및 금속 부품
• 유형: Bump-feed trimmer head

8. 보증 및 지원

This product is manufactured to high-quality standards. If you encounter any issues or have questions regarding the installation, operation, or compatibility of your INGQI Trimmer Head Replacement, please contact the seller directly through your purchase platform. Provide your order details for prompt assistance. All parts are tested and quality controlled prior to shipment.