VIMIN 10G PCI-E Network Card (Model AQC113) Instruction Manual

소개

This manual provides detailed instructions for the installation, configuration, and use of your VIMIN 10G PCI-E Network Card. Please read this manual thoroughly before installation to ensure proper operation and to maximize the performance of your network adapter.

주요 특징

• 10Gbps RJ45 Copper Port: Equipped with a Marvel AQC113 chipset, offering up to 10Gbps network speed for reliable high-speed data transfer.
• Rapid High-Speed Transmission: Supports PCIe 3.0 x4 bus interface, converting PCIe X4/X8/X16 slots into 10G RJ-45 Ethernet ports for efficient data transfer.
• 다목적 호환성: Supports various data rates including 10Gbps, 5Gbps, 2.5Gbps, 1Gbps, and 100Mbps Ethernet connections with intelligent auto-negotiation.
• Flexible Bracket Adaptability: Includes both low-profile and standard brackets for compatibility with diverse computer chassis.
• Seamless System Support: Compatible with Windows 10/11, Windows Server, and Linux operating systems. Drivers are provided via a USB drive.
• Protocol Standard Compliance: Compliant with IEEE 802.3an, IEEE 802.3bz, IEEE 802.3ab, IEEE 802.3u, IEEE 802.3x, IEEE 802.3az, IEEE 802.1Q standards.

패키지 내용

• 1 x VIMIN 10G PCI-E Network Card (AQC113)
• 1 x Standard Profile 브래킷 (사전 설치됨)
• 1 x 로우 프로file 까치발
• 1 x Driver USB Drive
• 1 x Quick Installation Guide (This manual serves as a detailed guide)

하드웨어 설치

1. 컴퓨터 전원을 끄고 전원 케이블을 분리하세요.
2. 컴퓨터 케이스를 엽니다.
3. Locate an available PCI Express x4, x8, or x16 slot on your motherboard.
4. Remove the corresponding slot cover from the computer chassis. If necessary, replace the standard bracket on the network card with the low-profile 까치발.
5. Carefully insert the VIMIN 10G PCI-E Network Card into the chosen PCIe slot until it is firmly seated.
6. Secure the network card with a screw to the computer chassis.
7. 컴퓨터 케이스를 닫고 전원 케이블을 다시 연결하세요.
8. Connect an Ethernet cable to the RJ45 port on the network card.

This image illustrates the three main steps for hardware installation: 1. Opening the chassis and removing the slot limiter. 2. Inserting the PCIe card into the slot. 3. Securing the bracket with screws.

The network card comes with both standard and low-profile brackets to fit various computer cases. It is compatible with PCI Express x4, x8, and x16 slots.

드라이버 설치

After hardware installation, you will need to install the appropriate drivers for your operating system.

1. 컴퓨터를 켜세요.
2. Insert the provided USB drive containing the drivers.
3. Navigate to the USB drive and locate the driver folder corresponding to your operating system (Windows, Linux).
4. Follow the on-screen instructions to install the drivers. For Windows, run the setup executable. For Linux, consult the README file within the driver folder for specific commands.
5. 드라이버 설치가 완료되면 컴퓨터를 다시 시작하십시오.

메모: In some cases, especially with newer Linux distributions, the driver may be automatically recognized and installed by the system.

운영 체제 호환성

The VIMIN 10G PCI-E Network Card supports a wide range of operating systems:

• 윈도우 10
• 윈도우 11
• Windows Server (various versions)
• Linux (various distributions)
• VM웨어

This network card is compatible with Windows 10/11, Windows Server, and Linux operating systems.

기술 사양

문제 해결

No Network Connection After Installation

• Verify Hardware Installation: Ensure the network card is fully seated in the PCIe slot and securely fastened.
• 케이블 연결 확인: Confirm the Ethernet cable is properly connected to both the network card and your router/switch.
• 드라이버 설치: Make sure the correct drivers for your operating system have been installed. Refer to the "Driver Installation" section.
• 장치 관리자(Windows): Check Device Manager to see if the network card is recognized and if there are any error symbols (e.g., yellow exclamation mark). Reinstall drivers if necessary.
• BIOS/UEFI 설정: Ensure the PCIe slot is enabled in your system's BIOS/UEFI settings.

네트워크 속도가 느립니다

• 케이블 품질: Use a high-quality Cat6a or Cat7 Ethernet cable for 10Gbps connections. Lower category cables may limit speed.
• Router/Switch Compatibility: Ensure your network router or switch supports 10Gbps speeds on the connected port.
• 드라이버 업데이트 : Check for the latest drivers from the VIMIN website or the provided USB drive.
• 시스템 리소스: High CPU usage or insufficient RAM on your computer can affect network performance.

Card Not Detected in Windows 11

• PCIe 슬롯 대역폭: Some motherboards share bandwidth between PCIe slots and M.2 NVMe slots. If the card is not detected, try moving it to a different PCIe slot or temporarily removing other M.2 devices to check for conflicts.
• Manual Driver Update: If the card appears in Device Manager but has issues, try manually updating the driver by searching for the Intel 10 Gigabit Ethernet driver pack and pointing Device Manager to the extracted driver files.

보증 및 기술 지원

The VIMIN 10G PCI-E Network Card comes with a 1-year after-sale service.

기술 지원, 문제 해결 또는 보증 관련 문의는 당사 지원팀으로 연락해 주십시오.

• 이메일: support@vimintech.com
• 온라인 지원: Visit the official VIMIN webFAQ 및 추가 리소스는 해당 사이트에서 확인하세요.

VIMIN offers dedicated customer support via email at support@vimintech.com, backed by a professional technical team providing 24-hour service.

안전 정보

• Always power off your computer and disconnect the power cable before installing or removing any internal components.
• Handle the network card by its edges to avoid touching the gold-plated connectors or sensitive components.
• 정전기 방전(ESD)으로 인한 손상을 방지하기 위해 적절한 정전기 방지 조치(예: 정전기 방지 손목 스트랩)를 사용하십시오.
• Ensure proper ventilation within your computer case to prevent overheating, especially for high-performance components.
• 기기를 직접 개조하거나 수리하지 마십시오. 자격을 갖춘 전문가에게 서비스를 의뢰하십시오.

제품 끝view 동영상