Sodola 24-Port 2.5Gb Easy Smart Managed PoE Switch User Manual

1. 서론

This manual provides detailed instructions for the installation, configuration, and operation of your Sodola 24-Port 2.5Gb Easy Smart Managed PoE Switch. This device is designed to provide high-speed network connectivity and Power over Ethernet (PoE) capabilities for various network devices.

The switch features 24 2.5Gb PoE ports and 2 10G SFP+ uplink ports, offering robust performance for demanding network environments. It supports web간편한 설정 및 모니터링을 위한 관리 기반 시스템입니다.

2. 패키지 내용

패키지에 다음 품목이 포함되어 있는지 확인하십시오.

• 1 x Sodola 24-Port 2.5G Managed PoE Switch
• 1 X 전원 코드
• 1 x 사용자 매뉴얼(이 문서)

3. 제품 오버view

The Sodola 24-Port 2.5Gb PoE Switch is a multi-gigabit managed switch designed for high-performance networking. It offers a combination of 2.5 Gigabit Ethernet ports with Power over Ethernet capabilities and 10 Gigabit SFP+ ports for high-speed uplinks.

3.1 주요 특징

• 2.5G & 10G PoE Switch: 24x 2.5Gb PoE ports + 2x 10G SFP+ ports for high-speed network connectivity.
• IEEE 802.3bt/at/af Compliant: Ports 1-4 support up to 90W each, and ports 5-24 support up to 30W each, with an overall PoE power budget of 500W. Note: Does not support passive 24V PoE devices.
• 쉬운 Web 관리: 직관적 web interface for device status monitoring and configuration of features like Link Aggregation, VLAN, QoS, Multicast, MAC, and RSTP.
• 160Gbps 대역폭: Robust switching capacity for lag-free data transfers.
• 보편적 인 호환성 : Compatible with various Ethernet devices such as 2.5G WiFi 6 APs, 2.5G NAS, 2.5G PCIe Adapters, and 2.5G Servers.
• 1U Rack Mounted Design: Supports 1U rack mounting and features a bilateral cooling design without a built-in fan for silent operation.

3.2 전면 패널 레이아웃

Figure 1: Front Panel Layout with Port and Indicator Labels

• 1. 1G/10G or 2.5G/10G SFP+ Ports: Two ports for high-speed fiber optic uplinks.
• 2. 24x 10/100/1000M/2.5G PoE Ports: Twenty-four 2.5 Gigabit Ethernet ports with Power over Ethernet capabilities.
• 3. RESET Button: 공장 설정으로 복원하려면 6초간 길게 누르세요.
• 4. LINK/ACT & PoE Indicators: LEDs indicating link status, activity, and PoE power status for each port.
• 5. SYS Indicator: 시스템 상태 표시등.
• 6. PWR Indicator: 전원 공급 장치 표시등.

3.3 후면 패널 레이아웃

Figure 2: Rear Panel Layout with Power Input and Grounding Screw

• 7. AC INPUT 100-240V: Power input for the switch.
• 8. Ground Screws: 전기적 안전을 보장하기 위해 접지선을 연결합니다.
• 9. PoE MAX Indicator: Shows the PoE power usage status (OFF: <90%, FLASHING: 90%-95%, ON: 95%-100%).

4. 설정

Follow these steps to set up your Sodola PoE Switch:

4.1 물리적 설치

• 데스크탑 배치: 스위치를 평평하고 안정적인 표면에 놓으세요. 기기 주변에 충분한 통풍이 되도록 하세요.
• 랙 장착: The switch supports 1U rack mounting. Use appropriate rack-mount brackets (not included unless specified) to secure the device in a standard 19-inch server rack.

Figure 3: Rack Mounting Example

4.2 전원 연결

1. Connect the provided power cord to the AC INPUT port on the rear panel of the switch.
2. Plug the other end of the power cord into a standard AC power outlet (100-240V).
3. The PWR indicator on the front panel should illuminate, indicating the switch is receiving power.

4.3 네트워크 연결

Connect your network devices to the switch using Ethernet cables. For optimal 2.5GbE speeds, use Cat6 or higher pure copper cables. Ensure all connected devices (routers, NICs, etc.) also support 2.5GbE; otherwise, network speed will default to the slowest connected device.

• PoE 장치: Connect PoE-compatible devices (e.g., IP cameras, wireless access points) to ports 1-24. These ports will automatically detect and provide power to compliant devices.
• PoE를 지원하지 않는 장치: Non-PoE devices can also be connected to ports 1-24 for data connectivity.
• 업링크 연결: Use the 10G SFP+ ports for high-speed connections to your core network, servers, or other 10G-capable devices.

5. 사용 설명서

The Sodola PoE Switch is largely plug-and-play for basic network connectivity. Once powered on and devices are connected, it will begin forwarding data.

5.1 LED 표시등

기기의 상태는 전면 패널의 LED 표시등을 통해 확인하십시오.

• PWR : 스위치에 전원이 들어오면 녹색으로 켜집니다.
• SYS : Indicates system status. Refer to the full user manual for specific blink patterns.
• LINK/ACT (포트별): Solid green when a link is established, flashing green when data is being transmitted/received.
• PoE (per port): Solid green when PoE power is being supplied to a connected device.
• PoE 최대: Indicates total PoE power usage. OFF: <90%, FLASHING: 90%-95%, ON: 95%-100%.

5.2 공장 설정으로 재설정

To restore the switch to its factory default settings, press and hold the RESET button on the front panel for approximately 6 seconds. The switch will reboot with default configurations.

6. Web 관리

이 스위치는 사용하기 쉬운 특징을 가지고 있습니다. web-based management interface for advanced configuration and monitoring.

6.1 액세스 Web 인터페이스

1. Ensure your computer is connected to the switch via an Ethernet cable.
2. Configure your computer's IP address to be in the same subnet as the switch's default IP address (e.g., if the switch is 192.168.2.1, set your computer to 192.168.2.x, where x is not 1).
3. 열기 web 브라우저에 접속하여 스위치의 기본 IP 주소를 입력하세요. 192.168.2.1
4. 기본 로그인 자격 증명을 입력하세요. 사용자 이름: admin, 비밀번호: admin.
5. 로그인에 성공하시면 다음 페이지에 접속하실 수 있습니다. web 관리 인터페이스.

그림 4: Web 관리 인터페이스 로그인

6.2 Configuration Features

그만큼 web interface allows you to configure various network settings, including:

• 링크 집계(LACP): 여러 개의 물리적 링크를 하나의 논리적 링크로 결합하여 대역폭과 중복성을 높입니다.
• VLAN : 보안과 성능을 개선하기 위해 네트워크를 분할하기 위해 가상 LAN(Virtual Local Area Network)을 만드세요.
• 서비스 품질(QoS): 중요한 애플리케이션이 충분한 대역폭을 받을 수 있도록 네트워크 트래픽의 우선순위를 지정합니다.
• 멀티캐스트(IGMP 스누핑): 네트워크 혼잡을 줄이기 위해 멀티캐스트 트래픽 전달을 최적화합니다.
• MAC 주소 관리: MAC 주소를 기반으로 액세스를 제어합니다.
• RSTP(고속 스패닝 트리 프로토콜): 네트워크 루프를 방지하고 네트워크 안정성을 확보하세요.
• 포트 미러링: 한 포트에서 다른 포트로 패킷 사본을 전송하여 네트워크 트래픽을 모니터링합니다.
• 점보 프레임 지원: Increase data transfer efficiency for large packets.

Important: After making any configuration changes in the web interface, navigate to the 'Tools' or 'Save' section and save your settings to ensure they are retained after a power cycle.

7. 사양

8. 문제 해결

• 전원 없음: Ensure the power cord is securely connected to both the switch and a working power outlet. Check the PWR LED.
• 링크/활동 없음: Verify that Ethernet cables are properly connected to both the switch and the network device. Check the LINK/ACT LED for the respective port. Ensure the connected device is powered on and functioning correctly.
• 네트워크 속도가 느립니다: For 2.5GbE connections, ensure you are using Cat6 or higher pure copper cables and that all devices in the network path support 2.5GbE.
• PoE 장치가 켜지지 않음: Confirm the connected device is PoE-compatible (IEEE 802.3af/at/bt). Check the PoE LED for the port. Ensure the total PoE power budget of 500W is not exceeded. Passive 24V PoE devices are not supported.
• 접근할 수 없습니다 Web 인터페이스: Verify your computer's IP address is in the same subnet as the switch's default IP (192.168.2.1). Ensure the correct default username and password ('admin'/'admin') are used. Try resetting the switch to factory defaults if the IP address has been changed and forgotten.
• Configuration Changes Not Saved: Remember to explicitly save configurations through the web 변경 후의 인터페이스입니다.

9. 유지관리

• 청소: 부드럽고 마른 천으로 스위치 외부를 닦으세요. 액체나 에어로졸 세척제는 사용하지 마세요.
• 통풍: Ensure the ventilation openings on the sides of the switch are not obstructed to allow for proper heat dissipation.
• 펌웨어 업데이트: 정기적으로 제조업체를 확인하십시오 web최적의 성능과 보안을 보장하기 위한 펌웨어 업데이트 사이트입니다.

10. 보증 및 지원

For warranty information, technical support, or service inquiries, please refer to the documentation included with your purchase or visit the official Sodola web대지. 보증 청구를 위해 구매 영수증을 보관하십시오.