TOTAL 20V Cordless Brushless Impact Wrench

1. 서론

Thank you for choosing the TOTAL 20V Cordless Brushless Impact Wrench, Model TIWLI2085. This manual provides essential information for the safe operation, maintenance, and troubleshooting of your tool. Please read it thoroughly before use and keep it for future reference.

Figure 1: The TOTAL TIWLI2085 impact wrench with its 20V battery installed, showcasing its compact design and readiness for operation.

2. 일반 안전 지침

전동 공구를 작동할 때는 화재, 감전, 신체 부상의 위험을 줄이기 위해 항상 기본적인 안전 예방 조치를 따르세요.

• 작업 영역 안전: 작업 공간을 깨끗하고 밝게 유지하세요. 어수선하거나 어두운 곳은 사고의 위험이 있습니다. 가연성 액체, 가스 또는 먼지가 있는 곳 등 폭발 위험이 있는 환경에서는 전동 공구를 작동하지 마세요.
• 전기 안전: 접지된 표면에 신체 접촉을 피하십시오. 전동 공구를 비나 습기에 노출시키지 마십시오.
• 개인 안전: 항상 눈 보호 장비를 착용하십시오. 장시간 작동 시에는 청력 보호 장비를 착용하십시오. 헐렁한 옷이나 장신구는 피하고, 긴 머리는 고정하십시오.
• 도구 사용 및 관리: 전동공구를 무리하게 사용하지 마십시오. 용도에 맞는 공구를 사용하십시오. 조정, 액세서리 교체 또는 보관 전에 전동공구에서 배터리 팩을 분리하십시오.
• 배터리 팩 사용 및 관리: Recharge only with the charger specified by the manufacturer. Do not use battery packs with any other power tools. Do not open, crush, or expose battery packs to fire or high temperatures.

3. 제품 오버view

The TOTAL TIWLI2085 is a powerful 20V cordless brushless impact wrench designed for heavy-duty fastening and loosening applications. It features a robust brushless motor for extended tool life and efficiency, an integrated LED work light for improved visibility, and multiple speed/impact settings for versatile use.

포함된 구성 요소:

• 1 x TOTAL 20V Cordless Brushless Impact Wrench (TIWLI2085)
• 2 x 4.0Ah Lithium-Ion Batteries (TFBLI2002)
• 1 x Charger (TFCLI2001E, 220-240V~50/60Hz)
• 3 x Deep Impact Sockets (22mm, 24mm, 27mm)
• 1 x 운반 가방

Figure 2: The TOTAL TIWLI2085 impact wrench displayed alongside the three included deep impact sockets (22mm, 24mm, 27mm), illustrating the complete kit.

4. 설정

4.1 배터리 충전

1. Connect the charger (TFCLI2001E) to a standard 220-240V~50/60Hz power outlet.
2. Slide the battery pack (TFBLI2002) onto the charger until it clicks into place.
3. 충전기의 충전 표시등이 켜지는데, 일반적으로 충전 중이면 빨간색, 완충되면 녹색으로 켜집니다.
4. 충전이 완료되면 충전기를 전원 콘센트에서 분리하고 배터리 팩을 꺼내십시오.

메모: For optimal battery life, allow the battery to cool down before charging if it has been heavily used. Do not store batteries in a discharged state.

4.2 Attaching/Removing Sockets

1. 안전을 위해 충격 렌치가 꺼져 있고 배터리가 제거되었는지 확인하세요.
2. Align the square drive of the desired impact socket (e.g., 22mm, 24mm, or 27mm) with the 1/2 inch square drive anvil on the tool.
3. Push the socket firmly onto the anvil until it locks into place. Some sockets may require pulling back a retaining ring or pin.
4. To remove, reverse the process, pulling back the retaining mechanism if present, and pull the socket off.

5. 사용 설명서

5.1 배터리 설치

Slide a charged battery pack into the base of the impact wrench handle until it clicks securely into place.

5.2 전원 켜기/끄기 및 방향 제어

• 켜기/끄기: Squeeze the trigger switch to turn the tool on. Release the trigger to turn it off. The integrated LED work light will activate when the trigger is pressed.
• 방향 제어: Use the forward/reverse selector switch, typically located above the trigger, to choose the rotation direction (clockwise for fastening, counter-clockwise for loosening). Ensure the switch is fully engaged in the desired position before operating.

5.3 Speed and Impact Rate Adjustment

The TIWLI2085 features multiple speed and impact rate settings, allowing you to match the tool's performance to the task. Refer to the tool's controls for specific adjustment methods, which typically involve a button or switch to cycle through settings:

• 무부하 속도: 0-1600 / 0-2100 / 0-2400 RPM
• 영향률: 0-1500 / 0-1800 / 0-2200 BPM

Start with a lower setting for delicate tasks or when first engaging a fastener, and increase as needed.

5.4 고정 및 풀기

1. 체결 부품에 맞는 소켓을 선택하십시오.
2. Set the direction switch to the desired mode (forward for fastening, reverse for loosening).
3. 소켓을 패스너에 끼우세요.
4. Squeeze the trigger to begin operation. Apply steady pressure to keep the socket engaged.
5. For fastening, tighten until the desired torque is achieved. For loosening, continue until the fastener breaks free.

Figure 3: The TOTAL TIWLI2085 impact wrench being used to fasten a lug nut on a car wheel, demonstrating its application for automotive tasks.

Figure 4: The TOTAL TIWLI2085 impact wrench in action, fastening a bolt on a metal workpiece, highlighting its versatility for various heavy-duty applications.

6. 유지관리

Regular maintenance ensures optimal performance and extends the life of your impact wrench.

• 청소: 공구의 통풍구를 깨끗하게 유지하고 이물질이 없도록 하십시오. 부드러운 천을 사용하십시오.amp cloth to wipe down the housing. Do not use harsh chemicals or abrasive cleaners.
• 배터리 관리 : 배터리는 직사광선과 극한의 온도를 피해 서늘하고 건조한 곳에 보관하십시오. 완전히 방전된 배터리를 장시간 보관하지 마십시오.
• 점검: Periodically inspect the square drive anvil for wear or damage. Check the power cord of the charger for any cuts or fraying.
• 매끄럽게 하기: This tool features a brushless motor and sealed components, requiring no user lubrication.

For any repairs or internal maintenance, contact qualified service personnel.

7. 문제 해결

This section addresses common issues you might encounter with your impact wrench.

8. 사양

Technical specifications for the TOTAL 20V Cordless Brushless Impact Wrench TIWLI2085:

9. 보증 및 지원

TOTAL products are manufactured to high-quality standards. For warranty information, service, or technical support, please refer to the warranty card included with your product or contact your local TOTAL dealer or customer service center. Keep your purchase receipt as proof of purchase.

For further assistance, visit the official TOTAL tools web사이트를 방문하거나 고객 지원팀에 문의하세요.