1. 중요한 안전 정보
Please read and understand all instructions and warnings in this manual before installing, operating, or servicing this heater. Failure to follow these instructions may result in property damage, personal injury, or death.
- 이 히터는 실내에서만 사용하도록 설계되었습니다.
- Propane Fuel Only: This appliance operates exclusively on liquid propane gas. Do not attempt to use any other fuel type.
- 무환기 작동: This is a vent-free appliance. Ensure adequate ventilation as specified in local codes and this manual.
- 전문적인 설치: 설치 및 서비스는 자격을 갖춘 설치자, 서비스 기관 또는 가스 공급업체를 통해 수행되어야 합니다.
- 고도 제한: Vent-free heaters do not operate reliably at elevations above 4,500 feet altitude.
- 산소 고갈 센서(ODS): This heater is equipped with an ODS safety pilot system designed to shut off the heater if oxygen levels in the room become too low. Do not tamp이 안전 기능을 사용하거나 우회할 수 없습니다.
- 가연성 물질에 대한 정리: Maintain proper clearances from combustible materials as indicated in the installation section.
- 캘리포니아 주민: This item is not for sale to residents in California. Check your local regulations before purchasing 및 설치.
2. 제품 오버view
The ProCom Heating ML200HBA-B is a 20,000 BTU liquid propane ventless blue flame heater designed to provide reliable supplemental heat for areas up to 950 square feet. It features manual controls and a push-button piezo ignition system, requiring no electricity for operation.
그림 2.1: 전면 view of the ProCom Heating ML200HBA-B Ventless Blue Flame Heater with base feet installed.
주요 특징:
- 20,000 BTU maximum heat output, heating up to 950 sq. ft.
- Operates on Liquid Propane only.
- No electricity required for operation, ideal during power outag에스.
- Push-button Piezo ignition for easy startup.
- Manual control with three heat settings: Low, Medium, High.
- Integrated Oxygen Depletion Sensor (ODS) for safety with automatic shut-off.
- Includes base feet for floor standing and a wall mounting bracket for wall installation.
Figure 2.2: Visual summary of the heater's operational features and benefits.
3. 설정 및 설치
This heater can be installed as a freestanding unit using the included base feet or permanently mounted to a wall using the provided wall bracket. Always ensure installation is performed by a qualified professional and adheres to all local codes and regulations.
3.1 풀기 및 검사
- 히터와 모든 구성품을 포장에서 조심스럽게 꺼내십시오.
- Inspect the heater for any shipping damage. If damage is found, do not install or operate the heater. Contact your dealer immediately.
- Verify that all included components are present: heater unit, base feet, wall mounting bracket, and necessary hardware (screws for feet and bracket).
3.2 위치 요구 사항
- Select a location that allows for proper clearances from combustible materials (walls, furniture, drapes, etc.). Refer to the heater's labels for specific clearance requirements.
- Ensure the room has adequate air circulation for vent-free operation.
- Do not install in bathrooms, bedrooms, or recreational vehicles.
- Avoid areas with high drafts or where the heater could be exposed to water.
그림 3.1: 예ample of the heater installed on a wall, demonstrating its compact profile.
3.3 Attaching Base Feet (for Freestanding Use)
- Carefully lay the heater on its back on a soft, protected surface.
- Align the base feet with the pre-drilled holes on the bottom of the heater.
- Secure the feet using the provided screws. Ensure they are tightened firmly.
Figure 3.2: Detail of the blue flame technology and the included base feet for stable placement.
3.4 벽면 장착(선택 사항)
- Refer to the detailed instructions included with the wall mounting bracket for proper installation.
- Ensure the wall can support the weight of the heater and that mounting hardware is appropriate for the wall material.
3.5 가스 연결
- Connect the heater to a liquid propane supply line. This connection must be made by a qualified professional.
- Ensure all gas connections are leak-tested using a non-corrosive leak detection solution. Never use an open flame to check for leaks.
- The heater operates at a specific gas pressure. Ensure the supply pressure is within the specified range for safe operation.
4. 사용 설명서
This heater features manual controls for ignition and heat output. No electrical power is required for basic operation.
4.1 Lighting the Heater (Piezo Ignition)
- 가스 공급 밸브가 열려 있는지 확인하십시오.
- Locate the control knob and the ignitor button on the heater.
- Push in and turn the control knob counter-clockwise to the 'PILOT IGN' position.
- While holding the control knob in, repeatedly press the ignitor button until the pilot flame ignites. You should see a small blue flame at the pilot burner.
- Continue to hold the control knob in for approximately 30-60 seconds after the pilot flame ignites. This allows the thermocouple to heat up and hold the pilot valve open.
- Release the control knob. If the pilot flame extinguishes, repeat steps 3-5.
- Once the pilot flame is stable, push in and turn the control knob counter-clockwise to your desired heat setting (LOW, MEDIUM, or HIGH). The main burner will ignite.
Figure 4.1: Manual control knob and ignitor button for operating the heater.
4.2 열 출력 조절
To adjust the heat output, simply push in and turn the control knob to one of the three settings: LOW, MEDIUM, or HIGH. The heater will adjust its flame intensity accordingly.
4.3 Turning Off the Heater
To turn off the heater, push in and turn the control knob clockwise to the 'OFF' position. Ensure the main burner and pilot flame are extinguished. For extended periods of non-use, also close the main gas supply valve.
5. 유지관리
Regular maintenance ensures the safe and efficient operation of your heater. Always disconnect the gas supply and allow the heater to cool completely before performing any maintenance.
- 청소: Periodically clean the exterior surfaces of the heater with a soft, damp 천. 연마성 세척제나 용매를 사용하지 마십시오.
- 버너 및 파일럿 영역: Keep the burner ports and pilot assembly clean and free of dust, lint, or debris. A soft brush or vacuum cleaner can be used. Blocked ports can affect performance and safety.
- 연례 검사: It is recommended to have the heater inspected annually by a qualified service technician to ensure all components are functioning correctly and safely.
- Do not paint any part of the heater.
6. 문제 해결
If you experience issues with your heater, consult the following troubleshooting guide. For problems not listed here or if solutions do not resolve the issue, contact a qualified service technician.
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| 파일럿이 켜지지 않습니다 | 가스 공급 없음 가스 라인의 공기 파일럿 오리피스가 막혔습니다 점화장치가 스파크를 일으키지 않음 | Ensure gas supply valve is open Bleed air from line by holding pilot knob in for longer Clean pilot orifice Check ignitor electrode for damage or proper gap |
| Pilot lights but will not stay lit when knob is released | Thermocouple not heating sufficiently 느슨한 열전대 연결 열전대 결함 | Hold control knob in longer after pilot lights Check and tighten thermocouple connection Replace thermocouple (professional service recommended) |
| 메인 버너가 켜지지 않습니다 | Pilot not lit Main burner orifice clogged 가스압이 낮음 | Ensure pilot is lit and stable Clean main burner orifice Verify adequate gas supply pressure |
| Heater produces an odor | Initial burn-off of manufacturing oils Dust/debris on burner 환기가 부족합니다 | Operate heater in a well-ventilated area for a few hours Clean burner area 적절한 실내 환기를 확보하세요 |
| 히터가 예기치 않게 꺼집니다. | Oxygen Depletion Sensor (ODS) activated 가스압이 낮음 파일럿 불꽃이 꺼졌습니다 | Increase ventilation in the room 가스 공급을 확인하세요 Relight pilot flame |
7. 사양
Detailed technical specifications for the ProCom Heating ML200HBA-B heater.
Figure 7.1: Product dimensions of the ProCom Heating ML200HBA-B heater.
| 특징 | 사양 |
|---|---|
| 상표 | ProCom |
| 모델 번호 | ML200HBA-B |
| 연료 유형 | 액체 프로판 |
| 열 출력 | 20,000 BTU/시간 |
| 난방 범위 | 최대 950제곱피트 |
| 제어 유형 | Manual (Low/Medium/High) |
| 점화 유형 | Push-button Piezo |
| 안전 기능 | Oxygen Depletion Sensor (ODS) with automatic shut-off |
| 전원 | 전기가 필요 없습니다 |
| 장착 옵션 | Floor Stand (with included feet), Wall Mount (with included bracket) |
| 제품 크기(L x W x H) | 19인치 x 9인치 x 24인치 |
| 품목 무게 | 23.1파운드 |
| 한국어: | 848660008413 |
8. 보증 및 지원
For warranty information, technical support, or to inquire about replacement parts, please contact ProCom Heating customer service. Keep your purchase receipt and model number readily available when contacting support.
연락처 정보는 일반적으로 제조업체 웹사이트에서 찾을 수 있습니다. web사이트 또는 제품 포장에 표시되어 있습니다.
