MAXSafes 10005NV Drawer Safe User Manual

소개

The MAXSafes 10005NV Drawer Safe provides secure and quick access storage for your valuables and firearms. It features advanced finger vein recognition technology, a programmable electronic keypad, and a manual key override. Designed for discreet placement, this safe offers robust protection with its heavy-duty construction and convenient features like internal LED lighting and emergency power options.

이미지: 이상view of MAXSafes 10005NV Drawer Safe with key features labeled.

설정 및 설치

포함된 구성 요소

• 1 x MAXSafes 10005NV Biometric Safe
• 1 x 사용자 설명서
• 2 x Override Keys
• Mounting Hardware (screws, mounting bracket)

배터리 설치

1. Open the safe using the override key (see 'Manual Key Override' in Operation section).
2. Locate the battery compartment inside the safe.
3. 배터리 커버를 제거합니다.
4. 올바른 극성을 확인하여 새로운 9V 알카라인 배터리를 삽입합니다.
5. 배터리 커버를 다시 장착하세요.

금고 설치하기

The safe can be installed under a desk, inside a cabinet, or on a nightstand using the provided mounting bracket and hardware. Ensure the mounting surface is sturdy enough to support the safe's weight (approximately 14.3 lbs).

1. Position the mounting bracket in your desired location.
2. Mark the drilling points through the pre-drilled holes on the bracket.
3. 필요한 경우 시험용 구멍을 뚫습니다.
4. 제공된 나사를 사용하여 장착 브래킷을 고정합니다.
5. Slide the safe onto the mounted bracket until it locks securely into place.

Image: Various installation options for the MAXSafes 10005NV Drawer Safe.

작업

금고 잠금 해제

The MAXSafes 10005NV offers three methods for unlocking:

• 손가락 정맥 인식: Place a registered finger on the scanner. The safe will unlock in approximately 0.3 seconds.
• PIN 코드: Enter your programmed 4-8 digit PIN code on the backlit digital keypad.
• 수동 키 재정의: In case of battery failure or forgotten codes, use one of the provided override keys to manually open the safe. The keyhole is located on the side of the safe.

Image: Three unlocking methods: Manual Key, Password Quick Access, and Finger Vein Recognition Quick Access.

Programming Finger Vein IDs

The safe can store up to 50 unique finger vein patterns.

1. 금고를 엽니다.
2. Locate the program button inside the safe (under a rubber cover).
3. Press the program button. The indicator lights will flash.
4. Place the finger you wish to register on the finger vein scanner.
5. Lift and place the same finger on the scanner two more times (total of three scans).
6. The indicator lights will confirm successful registration.
7. Repeat for additional finger vein IDs.

PIN 코드 프로그래밍

Only one PIN code can be stored at a time. Programming a new code will overwrite the previous one.

1. 금고를 엽니다.
2. Locate the program button inside the safe.
3. Press the program button. The indicator lights will flash.
4. 원하는 4~8자리 PIN 코드를 키패드에 입력하세요.
5. Press the program button again to confirm.
6. Re-enter the same 4-8 digit PIN code to verify.
7. The indicator lights will confirm successful programming.

Erasing All Finger Vein IDs

1. 금고를 엽니다.
2. Locate the program button inside the safe.
3. Press and hold the program button for 5 seconds.
4. While still holding the program button, press the '4' key on the keypad.
5. All registered finger vein IDs will be erased.

알람 모드

If three incorrect finger vein scans or PIN code entries are made consecutively, the safe's alarm will activate, and a 2-minute lockout period will begin. During this time, the safe cannot be opened using biometric or PIN methods. To end the lockout, enter a correct passcode, use a registered finger vein ID (if available), or remove and reinsert the 9V battery.

유지

배터리 교체

The safe requires one 9V alkaline battery. Replace the battery when the low battery indicator lights up or if the safe fails to respond. Always keep spare override keys in a secure location outside the safe.

비상 전원

In case the 9V battery is completely depleted, the safe features a Type-C emergency power outlet. Connect a Type-C cable to an external power source (e.g., power bank) to temporarily power the safe and gain access. This allows you to replace the internal 9V battery.

Image: Battery compartment design for easy 9V battery replacement.

Image: Type-C emergency outlet for temporary power when the battery is low.

청소

금고 외부를 부드러운 천으로 닦으세요.amp cloth. Do not use abrasive cleaners or solvents. Keep the finger vein scanner clean and dry for optimal performance.

문제 해결

• Safe does not open with finger vein: Ensure your finger is clean and dry. Try repositioning your finger on the scanner. If multiple attempts fail, use the PIN code or manual key.
• PIN 번호로 금고가 열리지 않습니다. Double-check the entered code. Ensure the keypad is responsive. If the alarm is active, wait for the lockout period to end or use the manual key.
• No power/Safe unresponsive: Replace the 9V battery. If the battery is completely dead, use the Type-C emergency power outlet to temporarily power the safe and then replace the internal battery.
• 경보가 자주 울립니다: Review recent access attempts. Ensure no unauthorized attempts are being made.

If you encounter persistent issues not covered here, please contact MAXSafes customer support for assistance.

명세서

Image: Exterior and interior dimensions of the safe.

보증 및 지원

For warranty information or technical support, please refer to the contact details provided with your product packaging or visit the official MAXSafes web사이트. 보증 청구에 대비해 구매 증빙 자료로 구매 영수증을 보관하세요.