1. 제품 오버view
The TOA Electronics VX-3004F AMQ is a voice alarm system frame designed for use with TOA's VX-3000 Series rack-mount type voice evacuation systems. This unit complies with the European Standard EN54-16 for fire alarm systems, providing control for voice evacuation announcements and status indications.
It supports up to 4 amplifiers, configurable as 1 zone with 1 amplifier, 4 AB-zones, or 3 AB zones with a standby amplifier. The front panel features various indicators for amplifier status, fault conditions, and system operation, along with control buttons for acknowledgment, reset, and lamp 테스트.
2. 전면 패널 레이아웃
그림 1: Front Panel of the VX-3004F AMQ Voice Alarm System Frame.
The front panel of the VX-3004F AMQ provides visual feedback on the system's operational status and allows for basic control. Key areas include:
- TOA Logo: Brand identification on the upper left.
- Amplifier Status Indicators: Located on the lower left, these LEDs show the status for up to four amplifiers (1, 2, 3, 4/SBY). Each amplifier has indicators for 정점 (overload), 신호 (audio presence), 작동하다 (active), and 힘 (에).
- Fault Status Indicators: Positioned in the center, these LEDs indicate various system faults. They are categorized by 존 (A and B, with indicators for 1, 2, 3, 4) and 일반적인 faults (퓨즈, 힘, CPU, 단위, 회로망, EMG MIC).
- 제어 버튼: Three buttons are located to the right of the fault status indicators: 확인 (Acknowledge), 다시 놓기, 그리고 LAMP 시험.
- 시스템 상태 표시기: On the upper right, these LEDs show overall system status: 힘 (main power), 달리다 (system operating), 비상 사태 (emergency mode active), and CPU OFF (CPU not running).
- Network/Link Indicators: Below the system status, LEDs for 랜에이, 랜 B, RS LINK A, 그리고 RS LINK B indicate network and communication link activity.
- 모델 번호: "VOICE EVACUATION FRAME VX-3004F" is printed on the lower right.
3. 설치 및 설정
3.1. 개봉 및 검사
Carefully unpack the VX-3004F AMQ frame and inspect it for any signs of damage during transit. Ensure all components listed in the packing materials are present. If any damage or missing parts are found, contact your supplier immediately.
3.2. 장착
The VX-3004F AMQ is designed for rack-mount installation. Secure the unit into a standard 19-inch equipment rack using appropriate mounting hardware. Ensure adequate ventilation around the unit to prevent overheating.
3.3. 전원 연결
Connect the unit to a 20 - 33 V DC power source using the removable 4-pin terminal block. Ensure correct polarity and a stable power supply. The power consumption is 24 W for the frame only, and up to 90 W when RS Link is outputting 2A.
3.4. Network and Link Connections
- LAN A, B: Connect standard 100BASE-TX network cables to the RJ45 connectors for network communication.
- RS Link A, B: Use shielded Category 5 twisted pair (CAT5-STP) or greater cables for RS Link connections. These provide power feed up to 1A per connector.
- DS Link: Connect to DS LINK of power supply units using shielded Category 5 twisted pair (CAT5-STP) cables.
- Analog Link: Connect to other VX-3004F, VX-3008F, or VX-3016F units via the RJ45 connectors for analog input/output.
4. 운영
4.1. 전원 켜기
Once all connections are secure, apply power to the unit. The 힘 indicator on the front panel should illuminate. After a brief initialization period, the 달리다 indicator will light up, signifying normal operation.
4.2. Amplifier Status Monitoring
모니터링 amplifier status indicators for each of the four amp리퍼 채널:
- 정점: 다음과 같은 경우에 켜집니다. amplifier output level is too high, indicating potential distortion.
- 신호: Illuminates when an audio signal is present at the amp리퍼 입력.
- 작동하다: 다음과 같은 경우에 켜집니다. amplifier is active and functioning.
- 힘: 다음과 같은 경우에 켜집니다. amplifier module has power.
4.3. Fault Status Monitoring
그만큼 결함 상태 section provides critical information regarding system health. If any fault indicator illuminates, refer to the Troubleshooting section.
- ZONE A/B (1-4): Indicates a fault within a specific speaker zone (A or B) for channels 1 through 4.
- 퓨즈: Indicates a blown fuse within the unit.
- 힘: 전원 공급 문제를 나타냅니다.
- CPU: Indicates a central processing unit malfunction.
- 단위: Indicates a general unit fault.
- NETWORK : Indicates a network communication error.
- EMG MIC: Indicates a fault with the emergency microphone.
4.4. 제어 버튼
- ACK (Acknowledge): Press to acknowledge a fault condition, which may silence an audible alarm or clear a flashing indicator.
- RESET : Press to reset the system after a fault has been resolved.
- LAMP TEST : Press and hold to illuminate all LED indicators on the front panel, verifying their functionality.
5. 유지관리
5.1. 청소
Regularly clean the exterior of the unit with a soft, dry cloth. Do not use liquid cleaners or abrasive materials. Ensure ventilation openings are free from dust and obstructions.
5.2. 환경 조건
Ensure the unit is operated within its specified temperature and humidity ranges. Avoid exposing the unit to direct sunlight, excessive heat, moisture, or corrosive environments.
5.3. 펌웨어 업데이트
Periodically check the TOA Electronics website for any available firmware updates for the VX-3004F AMQ. Follow the provided instructions carefully for any update procedures.
6. 문제 해결
This section provides guidance for common issues indicated by the front panel fault status LEDs.
| 지시자 | 가능한 원인 | 행동 |
|---|---|---|
| 힘 (System Status) Off | No DC power supply, power cable disconnected. | Check DC power source and cable connections. |
| 달리다 끄다 | System initialization failure, CPU error. | Check CPU fault indicator. Power cycle the unit. If issue persists, contact support. |
| 정점 (Amplifier) On | Amplifier input signal too high, output overload. | Reduce input signal level or check speaker line impedance. |
| 존 A/B (Fault Status) On | Fault detected in the specified speaker zone (e.g., open circuit, short circuit). | Inspect speaker lines and connections for the indicated zone. |
| 퓨즈 (Fault Status) On | 내부 퓨즈가 끊어졌습니다. | Contact qualified service personnel for fuse replacement. Do not attempt to replace fuses yourself. |
| 힘 (Fault Status) On | Internal power supply malfunction. | Power cycle the unit. If the fault persists, contact support. |
| CPU (Fault Status) On | Central Processing Unit error. | Power cycle the unit. If the fault persists, contact support. |
| 회로망 (Fault Status) On | Network communication error. | Check LAN cable connections and network configuration. |
| EMG MIC (Fault Status) On | Emergency microphone fault. | Check emergency microphone connection and functionality. |
After resolving a fault, press the 확인 button to acknowledge the fault and then the 다시 놓기 button to clear the fault condition and restore normal operation.
7. 사양
| 특징 | 세부 사항 |
|---|---|
| 모델 | VX-3004F AMQ |
| 전원 | 20 - 33 V DC, removable terminal block (4 pins) |
| 전력 소비 | 24 W (frame only) at 33V DC input, 90 W (RS Link: 2 A output) at 33 V DC input |
| LAN A, B | 2 Connectors, 100BASE-TX, TCP, UDP, ARP, ICMP, RTP, IGMP, FTP, HTTP, NTP, RSTP, PCM (48 kHz, 16 bits) |
| RS Link A, B | 2 Connectors, Max. 1 A power feed per connector, RJ45, Shielded Category 5 twisted pair cable (CAT5-STP) or greater |
| DS Link | RJ45, Shielded Category 5 twisted pair cable (CAT5-STP) |
| Analog Link | 1 input, 1 output, RJ45 (for VX-3004F, VX-3008F, VX-3016F) |
| 마치다 | Panel: Surface-treated steel plate, black, 30 percent gloss, paint |
| 치수(길이 x 너비 x 높이) | 13.58 x 19.02 x 5.22인치(34.5 x 48.3 x 13.25cm) |
| 무게 | 16.76파운드(7.6kg) |
| 규정 준수 | EN54-16 |
8. 보증 및 지원
8.1. 보증 정보
For detailed warranty information regarding your TOA Electronics VX-3004F AMQ, please refer to the warranty card included with your product or contact your authorized TOA Electronics dealer or distributor. Warranty terms and conditions may vary by region and purchase location.
8.2. 기술 지원
Should you encounter any issues not covered in this manual or require further technical assistance, please contact your local TOA Electronics technical support or authorized service center. Ensure you have your product model number (VX-3004F AMQ) and serial number available when seeking support.
