소개
The Fluval AC110 Power Filter is an external hang-on-back filtration system designed to provide superior 4-stage filtration for aquariums ranging from 60 to 110 US gallons (227-416 liters). This filter ensures crystal-clear and healthy water conditions through mechanical, chemical, and biological filtration processes. This manual provides detailed instructions for the proper setup, operation, and maintenance of your Fluval AC110 Power Filter.
안전 지침
- Always disconnect all electrical appliances from the mains power supply before placing hands in the aquarium, performing maintenance, or handling the filter.
- Ensure the filter is securely mounted to the aquarium rim and filled with water before connecting to power.
- 필터의 부품이 손상되었거나 전원 코드가 닳은 경우 작동하지 마십시오.
- 이 제품은 실내에서만 사용하도록 설계되었습니다.
- 어린이의 손이 닿지 않는 곳에 보관하세요.
패키지 내용
모든 구성품을 조심스럽게 풀어서 다음 품목이 있는지 확인하세요.
- Fluval AC110 Power Filter Unit
- 프리필터 스펀지
- BioFoam Insert
- BioMax Insert (biological media)
- Carbon Insert (chemical media)
- Intake Tube Assembly
- Output Spout
이미지: 폭발 view of the Fluval AC110 Power Filter showing all included parts for assembly.
설치 지침
- 포장 풀고 검사하기: Remove all packaging materials and inspect the filter and its components for any damage.
- 흡입 튜브 조립: Connect the intake tube sections and attach the pre-filter sponge to the bottom of the intake tube.
- 필터 미디어 설치: Place the filter media into the filter basket in the following order from bottom to top: BioFoam, Carbon Insert, BioMax Insert. Ensure they are seated correctly.
- 마운트 필터: Hang the filter unit securely on the back rim of your aquarium. Ensure it is level and stable.
- 위치 흡입 튜브: Insert the assembled intake tube into the filter unit and adjust its length so the pre-filter sponge is submerged in the aquarium water, ideally near the bottom.
- 물로 채우십시오: Manually fill the filter reservoir with aquarium water until it is full. This primes the pump and prevents dry running.
- 전원 연결: Once the filter is filled with water and securely mounted, plug the power cord into a grounded electrical outlet. The filter should start operating immediately.
Image: The Fluval AC110 Power Filter fully assembled, showing the intake tube and media basket.
이미지: 컷어웨이 view of the Fluval AC110 filter, illustrating the four stages of filtration media: (1) pre-filter sponge, (2) BioFoam, (3) carbon insert, and (4) BioMax biological media.
작동 지침
Once properly set up and plugged in, the Fluval AC110 Power Filter will begin circulating and filtering your aquarium water. The filter is designed for continuous operation to maintain water quality.
흐름 제어
The Fluval AC110 features an adjustable flow control knob, typically located on the top of the filter unit. This allows you to regulate the water flow rate to suit the needs of your aquarium inhabitants. Turn the knob clockwise to decrease flow and counter-clockwise to increase flow.
Re-priming After Power Outage
정전이 발생한 경우tage, the filter may lose its prime. Once power is restored, if the filter does not restart automatically or if the water flow is weak, unplug the unit, manually fill the filter reservoir with aquarium water, and then plug it back in. This will re-prime the pump.
유지
Regular maintenance is crucial for the optimal performance and longevity of your Fluval AC110 Power Filter and the health of your aquarium.
주간 유지 관리
- 유량 확인: Ensure the water flow is consistent and strong. A reduced flow rate may indicate clogged media.
- Clean Pre-filter Sponge: Gently rinse the pre-filter sponge in old aquarium water (removed during a water change) to remove trapped debris. Do not use tap water as chlorine can harm beneficial bacteria.
월별 유지 관리
- Rinse BioFoam: Lightly rinse the BioFoam insert in old aquarium water. Avoid excessive cleaning to preserve beneficial bacteria.
- Replace Carbon Insert: The carbon insert should be replaced every 2-4 weeks, or as needed, to maintain chemical filtration effectiveness.
- 임펠러 청소: Unplug the filter and carefully remove the motor unit and impeller. Clean the impeller and its housing with a small brush to remove any debris or mineral buildup.
2-3개월마다
- Rinse BioMax: Gently rinse the BioMax biological media in old aquarium water. Only clean if visibly clogged, as it houses essential beneficial bacteria.
이미지: 상세한 내부 구조 view of the Fluval AC110 Power Filter, highlighting the motor and impeller assembly, which should be cleaned regularly.
문제 해결
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| 필터가 시작되지 않거나 흐름이 약함 | Not primed, clogged intake, clogged media, impeller issue | Ensure filter is filled with water. Clean intake tube and pre-filter sponge. Check and clean impeller. Replace clogged media. |
| 과도한 소음/덜거덕거림 | Impeller not seated correctly, air in filter, debris in impeller housing, filter not level | Unplug and re-seat impeller. Ensure filter is fully primed and free of air. Clean impeller and housing. Verify filter is level on the aquarium rim. |
| 필터에서 물이 넘쳐흐릅니다 | 막힌 필터 매체 | Clean or replace filter media, especially the BioFoam and pre-filter sponge. |
| 흐린 물 | Insufficient filtration, new tank syndrome, overfeeding, dirty media | Perform partial water change. Ensure all filter media are clean and functioning. Do not overfeed. Check for proper biological filtration establishment. |
명세서
- 모델: Fluval AC110 (Model Number: 19620)
- 수족관 수용 인원: 60-110 US Gallons / 227-416 Liters
- 펌프 출력: 500 US GPH (Gallons Per Hour)
- 여과 Stag에스: 4-stage (기계적, 화학적, 생물학적)
- 품목 무게: 2.2파운드(1킬로그램)
- 제품 크기(LxWxH): 6.85 x 13.62 x 9.21인치(17.4 x 34.6 x 23.4cm)
- 제조업체: Rolf C. Hagen (미국) Corp.
- 포함된 구성 요소: Power Filter, pre-filter sponge, biofoam insert, biomax insert, carbon insert
Image: Diagram showing the key dimensions of the Fluval AC110 Power Filter for proper placement and fit.
보증 및 지원
For warranty information or technical support, please refer to the documentation included with your product packaging or visit the official Fluval web사이트. 보증 청구를 위해 구매 증빙 자료를 보관하세요.
제조업체: Rolf C. Hagen (미국) Corp.
