소개
This manual provides detailed instructions for the Kanlux LOGI Two-Gang Chandelier Switch with LED, Model 33623. It covers product features, safety guidelines, installation procedures, operation, maintenance, troubleshooting, and technical specifications. Please read this manual thoroughly before installation and use to ensure safe and efficient operation of the device.
The Kanlux LOGI switch is designed to independently control two separate lighting circuits, making it suitable for managing multiple lamps or chandeliers from a single location. Its integrated LED backlight enhances visibility in dark environments. This product is intended for indoor use and complies with IP20 protection standards, capable of handling a load of 10AX at 250V AC.
안전 정보
경고: 감전의 위험. Always disconnect power at the circuit breaker or fuse box before installing, servicing, or removing the switch. Failure to do so can result in serious injury or death.
- Installation should only be performed by a qualified electrician or trained personnel in accordance with all local and national electrical codes.
- Do not install this device in wet locations or outdoors. It is rated IP20 for indoor use only.
- 볼륨을 확보하세요tage and current ratings of your electrical system are compatible with the switch's specifications (250V AC, 10AX).
- 스위치의 최대 부하 용량을 초과하지 마십시오.
- Inspect the switch for any damage before installation. Do not install a damaged device.
- 전기 설비에 어린이가 접근하지 못하도록 하십시오.
제품 끝view
The Kanlux LOGI Two-Gang Chandelier Switch is designed for reliable control of two independent lighting circuits. Its minimalist design integrates seamlessly into various interior styles.
- Two Levers: Allows independent control of two separate lighting circuits.
- LED 백라이트: Facilitates easy identification and operation of the switch in low-light conditions.
- 내구성 있는 구조: Designed for interior use with an IP20 protection rating.
- 표준 호환성: Operates at 250V AC with a 10AX current capacity.
그림 1: Technical drawing of the Kanlux LOGI Two-Gang Chandelier Switch. This diagram illustrates the front view of the switch module, indicating its square form factor with dimensions of 71mm by 71mm. The two independent switch levers are visible, along with the Kanlux brand logo and mounting points. This image helps in understanding the physical size and layout for installation planning.
설정 및 설치
중요한: 설치는 자격을 갖춘 전기 기술자가 수행해야 합니다.
- 전원 차단: Before starting any electrical work, ensure the main power supply to the circuit is turned off at the circuit breaker or fuse box. Verify with a voltag전자 테스터.
- 배선 준비: Carefully strip the insulation from the ends of the electrical wires (live, neutral, and load wires for each circuit) according to local electrical codes and the switch's terminal requirements.
- 전선 연결:
- Connect the incoming live wire (L) to the common terminal of the switch.
- Connect the load wire for the first lighting circuit to the first output terminal (e.g., L1).
- Connect the load wire for the second lighting circuit to the second output terminal (e.g., L2).
- 모든 연결이 안전하고 단단한지 확인하십시오.
- 스위치 장착: Gently push the wired switch module into the wall box. Secure it using the provided screws. Ensure the switch is level and flush with the wall surface.
- 페이스플레이트 부착: Install the decorative faceplate over the switch module.
- 복원력 : 설치가 완료되고 모든 연결이 안전한 경우 회로 차단기에서 전원을 복구하세요.
- 테스트 작업: Test both switch levers to ensure they correctly control their respective lighting circuits.
작동 지침
The Kanlux LOGI Two-Gang Chandelier Switch provides straightforward control for two lighting circuits.
- 조명 켜기/끄기: Press the upper or lower part of each switch lever to toggle the connected lighting circuit on or off. Each lever operates independently.
- LED 백라이트: The integrated LED backlight will illuminate when the switch is in the 'off' position (or 'on' depending on wiring configuration and local standards) to help locate it in the dark.
유지
The Kanlux LOGI switch requires minimal maintenance.
- 청소: To clean the switch, first ensure power is disconnected at the circuit breaker. Use a soft, dry cloth to wipe the surface. Do not use abrasive cleaners, solvents, or excessive moisture, as these can damage the finish or internal components.
- 점검: Periodically check the switch for any signs of damage, loose connections, or unusual operation. If any issues are observed, disconnect power and consult a qualified electrician.
문제 해결
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| 조명이 켜지거나 꺼지지 않습니다. |
|
|
| LED 백라이트가 작동하지 않습니다. |
|
|
| 스위치가 헐렁하거나 흔들거리는 느낌이 듭니다. |
|
|
If you encounter problems not listed here or if the suggested solutions do not resolve the issue, please contact a qualified electrician or Kanlux customer support.
명세서
| 상표 | 칸룩스 |
| 모델 번호 | 33623 |
| 유형 | Two-Gang Chandelier Switch with LED |
| 입력 Voltage | 250V 교류 |
| 현재 평가 | 10AX |
| IP 보호 등급 | IP20 (Suitable for indoor use) |
| Number of Levers | 2 (Independent control of two circuits) |
| 특별 기능 | LED를 백라이트 |
| 품목 무게 | 90그램 |
| 치수 | 71 x 71 mm (as per technical drawing) |
보증 및 지원
Specific warranty information for the Kanlux LOGI Two-Gang Chandelier Switch (Model 33623) was not provided in the product details. For warranty terms and conditions, please refer to the documentation included with your purchase or visit the official Kanlux web대지.
For technical support, product inquiries, or assistance with installation, please contact Kanlux customer service or your local distributor. Contact information can typically be found on the manufacturer's web사이트 또는 제품 포장에 표시되어 있습니다.
제조업체: 칸룩스
