TFA Dostmann 무선 기상 관측소 Clear 35.1168.02 사용 설명서
Model: 35.1168.02 | Brand: TFA Dostmann
1. 서론
This manual provides detailed instructions for the setup, operation, and maintenance of your TFA Dostmann Clear 35.1168.02 Wireless Weather Station. Please read this manual thoroughly before using the device to ensure correct operation and to prevent damage.
The weather station monitors indoor and outdoor temperature and humidity, and provides a weather forecast based on atmospheric pressure changes.
2. 안전 정보
- 장치와 배터리를 어린이의 손이 닿지 않는 곳에 보관하십시오.
- 장치를 극한의 온도, 진동 또는 충격에 노출시키지 마십시오.
- 직사광선과 습기를 피하세요.
- 장치를 물에 담그지 마십시오.
- Use only specified batteries. Ensure correct polarity.
- Replace all batteries simultaneously.
- Dispose of depleted batteries and the device according to local regulations.
- The outdoor sensor should be placed in a sheltered location, protected from direct precipitation.
3. 패키지 내용
- Base Station (Weather Station)
- Thermo-Hygrometer Outdoor Sensor (Model: 30.3256.02)
- 사용자 설명서
Note: 4 x 1.5V AAA batteries (2 for base station, 2 for outdoor sensor) are required and not included.
4. 제품 오버view
Figure 1: TFA Dostmann Clear 35.1168.02 Wireless Weather Station (Base Unit and Outdoor Sensor).
This image displays the main weather station unit on the right, showing its digital display with atmospheric pressure, weather icons, outdoor temperature and humidity, and indoor temperature and humidity. To the left is the compact outdoor sensor, also displaying temperature and humidity.
4.1 Base Station Display Elements
Figure 2: Close-up of the Weather Station Display.
The display shows: atmospheric pressure (hPa), weather forecast icons (sunny, partly cloudy, cloudy, rainy), outdoor channel indicator (CH 1 OUT), outdoor temperature (°C/°F) and humidity (%), and indoor temperature (°C/°F) and humidity (%).
- 기압: Displayed in hPa, with trend arrows.
- 일기 예보 아이콘: 4 symbols (sunny, partly cloudy, cloudy, rainy) based on pressure changes.
- 실외 온도 및 습도: From the wireless sensor.
- 실내 온도 및 습도: Measured by the base station.
- 채널 표시기: Shows which outdoor sensor channel is currently displayed (up to 3 sensors supported).
4.2 Base Station Control Buttons (Rear)
Figure 3: Rear of the Base Station showing control buttons and battery compartment.
The rear panel features four control buttons: DOWN, UP, CHANNEL, and SET. These buttons are used for navigating settings, adjusting values, and switching between outdoor sensor channels.
- 내려가는: Decreases values, navigates menus.
- 쪽으로: Increases values, navigates menus.
- 채널: Switches between outdoor sensor channels (if multiple sensors are paired).
- 세트: 설정 모드로 진입하여 선택 사항을 확인합니다.
5. 설정
5.1 배터리 설치
- 실외 센서: Open the battery compartment on the back of the outdoor sensor. Insert 2 x 1.5V AAA batteries, observing correct polarity (+/-). Close the compartment.
- 기지국: Open the battery compartment on the back of the base station. Insert 2 x 1.5V AAA batteries, observing correct polarity (+/-). Close the compartment.
- The base station will emit a short beep and all LCD segments will light up briefly. It will then display indoor temperature and humidity. The outdoor sensor data will appear shortly after.
5.2 센서 페어링
The base station will automatically attempt to connect to the outdoor sensor upon battery insertion. Ensure the sensor is within range (max. 100m in open air). If connection is not established, press the "CHANNEL" button on the base station to initiate a manual search.
The station supports up to three outdoor sensors. To add additional sensors, repeat the battery installation process for each new sensor. Use the "CHANNEL" button to cycle through and display data from different sensors.
5.3 Initial Settings (Atmospheric Pressure)
The atmospheric pressure needs to be set during initial setup for accurate weather forecasting. Consult a local weather service or online source for the current atmospheric pressure in your area.
- Press and hold the "SET" button until the atmospheric pressure value flashes.
- Use the "UP" or "DOWN" buttons to adjust the value to your local atmospheric pressure.
- Press "SET" again to confirm and exit the setting mode.
5.4 배치
- 기지국: Place the base station indoors on a flat surface or mount it on a wall. Avoid placing it near heat sources, direct sunlight, or areas with high electromagnetic interference.
- 실외 센서: Position the outdoor sensor in a sheltered location, protected from direct rain and snow. Ensure good air circulation around the sensor. Avoid direct sunlight to prevent inaccurate temperature readings. The maximum range is 100m (open field).
6. 기상 관측소 작동
6.1 Displaying Temperature and Humidity
The base station continuously displays indoor temperature and humidity, along with the selected outdoor sensor's temperature and humidity.
6.2 온도 단위 전환 (°C/°F)
To switch between Celsius and Fahrenheit, briefly press the "UP" button outside of setting mode.
6.3 일기예보
The weather station provides a forecast for the next 12-24 hours using four weather icons: sunny, partly cloudy, cloudy, and rainy. These forecasts are based on changes in atmospheric pressure. The accuracy of the forecast improves after the initial atmospheric pressure setting has been stable for several hours.
6.4 Atmospheric Pressure Trend
Arrows next to the atmospheric pressure display indicate whether the pressure has risen, fallen, or remained stable over the last hour. This helps in understanding short-term weather trends.
7. 유지관리
7.1 청소
부드러운 천으로 장치를 청소하십시오.amp 천으로 닦아주세요. 연마성 세제나 용제는 사용하지 마세요. 기기에 습기가 들어가지 않도록 주의하세요.
7.2 배터리 교체
Replace batteries when the low battery indicator appears on the display. Always replace all batteries in a unit (base station or sensor) simultaneously to ensure optimal performance. Dispose of old batteries responsibly.
8. 문제 해결
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| 실외 온도/습도 표시 기능이 없습니다. |
|
|
| 부정확한 일기예보. |
|
|
| 디스플레이가 어둡거나 아무것도 표시되지 않습니다. |
|
|
9. 사양
| 특징 | 세부 사항 |
|---|---|
| 모델 번호 | 35.1168.02 |
| 실외 온도 범위 | -20 ° C ~ + 60 ° C (-4 ° F ~ + 140 ° F) |
| 실내 온도 범위 | -10°C ~ +50°C(+14°F ~ +122°F) |
| 실내 습도 범위 | 상대 습도 20% ~ 95% |
| 재료 | 플라스틱 |
| Maximum Range (Outdoor Sensor) | 100m(개방된 들판) |
| Included Transmitter Model | 30.3256.02 (Max. 3 transmitters supported) |
| 전송 주파수 | 433MHz |
| 장착 옵션 | 테이블 스탠딩 또는 벽걸이 |
| Power Supply (Batteries) | Base Station: 2 x 1.5V AAA (not included) Outdoor Sensor: 2 x 1.5V AAA (not included) |
| 치수(길이 x 너비 x 높이) | 94 x 20(58) x 105(101)mm |
| 무게 | 109g |
10. 보증 및 지원
TFA Dostmann products are manufactured with quality and precision. For warranty information and technical support, please refer to the official TFA Dostmann web사이트를 방문하거나 가까운 대리점에 문의하세요. 구매 영수증을 구매 증빙 자료로 보관하세요.
예비 부품 공급 기간: 1년.
제조사: TFA 도스트만
원산지 : 중국
