소개
The SparkFun LTE Stick provides a development and prototyping platform for the LARA-R6 LTE Cat 1 module from u-blox. This version, LARA-R6401, is designed for North America, supporting both data and voice communication across major mobile networks including AT&T, Verizon, T-Mobile, and FirstNet. It features a nanoSIM card slot for network selection and includes common u-blox functionalities like uFOTA (over-the-air firmware updates), Root of Trust, secure boot/update, jamming detection, and antenna/SIM detection.
The board routes UART and I2S interfaces to a 0.1-inch spaced plated-through-hole (PTH) header, along with Reset and Power On signals, facilitating easy breadboard prototyping. It also includes two SMA connectors for primary and secondary antennas, and power can be supplied via USB-C or the VIN PTH pin.
제품 끝view
설정
1. 전원 공급
The SparkFun LTE Stick can be powered in two ways:
- USB-C 커넥터 : This is the recommended power source. Connect a standard USB-C cable to the board and a power source (e.g., computer USB port, USB wall adapter).
- VIN PTH Pin: For advanced users, power can be supplied via the VIN plated-through-hole pin. The maximum input voltage for VIN is 6V. The board defaults to using the higher voltage input if both are connected.
2. SIM 카드 설치
The board includes a nanoSIM card slot. Insert your nanoSIM card into the designated slot. Ensure the SIM card is oriented correctly as indicated on the board.
메모: Check with your network provider for compatibility with the LARA-R6 module.
3. 안테나 연결
The LTE Stick features two SMA connectors for antennas:
- Primary Antenna (ANT1): This antenna is used for both transmitting and receiving data.
- Secondary Antenna (ANT2): This antenna is receive-only.
Connect appropriate LTE antennas to these SMA connectors. For optimal performance, ensure both antennas are connected.
4. Interfacing with Microcontrollers
The board provides PTH headers for easy connection to breadboards and microcontrollers:
- UART 인터페이스: Primary communication interface for data.
- I2S Interface: For digital audio applications, enabling voice functionality.
- Reset and Power On Signals: Accessible via PTH for external control.
Test points are available for advanced users to solder to for the I2C interface, secondary UART, and four GPIO pins (IO1, IO2, IO3, and IO6). These test points are 1.8V only and are not level-shifted.
작동 지침
기본 동작
- Ensure the SIM card is properly inserted and antennas are connected.
- Connect the USB-C cable to power the device. The power LED on the board should illuminate.
- Use the UART interface to communicate with the LARA-R6 module via AT commands. Refer to the u-blox LARA-R6 series documentation for a comprehensive list of AT commands and their usage.
- For voice applications, connect an audio codec, microphone, and speaker to the I2S interface and implement the necessary code on your microcontroller.
Firmware Updates (uFOTA)
The LARA-R6 module supports uFOTA (over-the-air firmware updates). Consult u-blox documentation for detailed procedures on performing firmware updates to ensure your module has the latest features and security enhancements.
유지
- 보드를 깨끗하게 유지하고 먼지와 이물질이 없도록 하세요.
- 기판을 극한의 온도나 습도에 노출시키지 마십시오.
- Ensure proper ventilation when operating for extended periods.
- Handle the board by its edges to prevent damage to components.
- Regularly check for and apply firmware updates as recommended by u-blox to maintain optimal performance and security.
문제 해결
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| 보드 전원이 켜지지 않습니다. | Incorrect power supply; loose USB-C connection; VIN voltage 범위를 벗어났습니다. | Ensure USB-C cable is securely connected and functional. Verify VIN voltage is within 3.3V-6V range if using PTH. |
| 네트워크에 연결되지 않았습니다. | SIM card not inserted correctly; incompatible SIM card; antenna issues; network not supported. | Re-insert SIM card, ensuring correct orientation. Verify SIM card is active and compatible with LARA-R6. Check antenna connections. Confirm network support for LARA-R6 bands. |
| Communication issues via UART. | Incorrect baud rate; wiring errors; module not initialized. | Verify baud rate settings match the module's configuration. Check UART wiring for continuity and correct pin connections. Ensure the module is powered and initialized. |
| Voice functionality not working. | I2S wiring issues; audio codec not configured; software implementation errors. | Review I2S wiring. Ensure audio codec is correctly connected and configured. Debug software for proper I2S and voice handling. |
명세서
- 모듈 : u-blox LARA-R6401 LTE Cat 1
- 지역: 북아메리카
- LTE FDD 대역: 2, 4, 5, 12, 13, 14, 66, 71
- 인터페이스:
- 2x UART
- USB 2.0
- I2C
- 9개의 GPIO 핀
- Digital Audio (I2S)
- SIM 카드 슬롯: 나노 SIM
- 안테나 커넥터: 2x SMA (Primary: Transmit & Receive, Secondary: Receive Only)
- 전원 입력: USB-C (recommended) or VIN PTH pin (6V Max)
- 운영 볼륨tage: 3.3V or 1.8V (for test points)
- 치수: 3.74 x 0.98 x 0.2 인치
- 무게: 8 온스
지원하다
For additional support, technical documentation, and community forums, please visit the official SparkFun website or the u-blox documentation portal for the LARA-R6 series.
SparkFun Store: Amazon에서 SparkFun 스토어를 방문하세요.
