HBL9100 바코드 스캐너 배터리 사용 설명서

1. 서론

This manual provides essential information for the safe and effective use of the HBL9100 Barcode Scanner Battery. Designed specifically for the Urovo i9100 barcode scanner, this Li-ion battery offers reliable power for extended operation. Please read this manual thoroughly before installation and use to ensure optimal performance and safety.

2. 안전 정보

리튬 이온 배터리는 조심스럽게 다루어야 합니다. 다음 안전 지침을 준수하십시오.

• 배터리 팩을 분해하거나, 열거나, 수리하려고 시도하지 마십시오. This will void the warranty and can be dangerous.
• 본 제품에 지정된 배터리 팩으로만 교체하세요. Using incompatible batteries may cause fire or explosion.
• 부수거나, 구멍을 뚫거나, 외부 접촉을 단락시키거나, 불이나 물 속에 버리지 마십시오. Mishandling can lead to severe damage or injury.
• 60°C(140°F) 이상의 온도에서 보관하지 마십시오. 고온은 배터리 성능을 저하시키고 안전 위험을 초래할 수 있습니다.
• 사용한 배터리는 지역 규정에 따라 폐기하십시오. 일반 생활 쓰레기와 함께 버리지 마십시오.

이미지: 앞면 view of the HBL9100 battery, showing the label with important safety warnings and specifications.

3. 제품 오버view

The HBL9100 is a high-capacity Li-ion replacement battery for the Urovo i9100 barcode scanner. It features a robust design and includes multiple protection mechanisms to ensure safe and reliable operation.

주요 특징:

• High Capacity: 5200mAh / 19.24Wh for extended usage.
• 권tage: 3.7V Li-ion.
• Safety Protections: Over-charge, over-discharge, over-heat, over-current, and short-circuit protection.
• Quality Certifications: ROSH, CE, and UL triple certification.
• No Memory Effect: Allows for flexible charging without degrading battery capacity.

이미지: 위에서 아래로 view of the HBL9100 battery, showcasing its compact design and label.

이미지: 클로즈업 view of the battery's connector, showing the wiring for proper installation.

4. 설정 및 설치

Before installing the new battery, ensure your Urovo i9100 barcode scanner is powered off and disconnected from any power source.

1. 배터리 칸 찾기: Identify the battery compartment on your Urovo i9100 scanner. Refer to your scanner's original manual if unsure.
2. 오래된 배터리 제거: Carefully open the battery compartment cover. Disconnect the old battery's connector and remove it.
3. 새 배터리를 삽입하세요: Align the HBL9100 battery with the compartment. Ensure the connector cable is positioned correctly.
4. 배터리 연결: Gently push the battery connector into the corresponding port on the scanner. Ensure it clicks securely into place.
5. 구획 닫기: 배터리 칸 덮개를 다시 끼우고 단단히 고정했는지 확인하세요.
6. 초기 청구 : It is recommended to fully charge the battery before its first use. Connect your Urovo i9100 scanner to its charger and allow it to charge until the charging indicator shows full.

이미지: 각도 view of the HBL9100 battery, illustrating its form factor for proper fitment.

5. 운영 지침

Once installed and charged, the HBL9100 battery will power your Urovo i9100 barcode scanner. The scanner's power management system will regulate battery usage.

• 일반 충전: Charge the battery regularly to maintain optimal performance. Avoid letting the battery completely drain before recharging.
• 온도: Operate the scanner within its recommended temperature range. Extreme temperatures can affect battery life and performance.
• 사용하지 않을 때 전원 끄기: If the scanner will not be used for an extended period, power it off to conserve battery life.

6. 유지 관리 및 보관

Proper maintenance and storage can significantly extend the lifespan of your HBL9100 battery.

• 완전 퇴원을 피하십시오: While the battery has protection against over-discharge, frequent deep discharges can reduce overall lifespan.
• 최적의 스토리지: If storing the battery for an extended period (more than a month), charge it to approximately 50-60% and store it in a cool, dry place, away from direct sunlight and extreme temperatures.
• 정기적 사용: For best results, use and recharge the battery regularly.
• 청소: 배터리 접촉면에 먼지나 이물질이 묻지 않도록 깨끗하게 유지하십시오. 필요한 경우 마른 부드러운 천으로 닦으십시오.

7. 문제 해결

If you encounter issues with your HBL9100 battery, consider the following common solutions:

• 배터리가 충전되지 않음:
  • Ensure the charger is properly connected to the scanner and the power outlet.
  • Verify the battery is correctly seated in the compartment and its connector is secure.
  • Check if the charger or charging cable is damaged. Try a different charger if available.
• 스캐너 전원이 켜지지 않음:
  • 배터리가 완전히 충전되었는지 확인하십시오.
  • Confirm the battery is correctly installed and the connector is firm.
  • If the scanner still does not power on, the issue might be with the scanner itself, not the battery.
• 배터리 수명이 짧음:
  • 사용하기 전에 배터리가 완전히 충전되어 있는지 확인하세요.
  • Check for applications or settings on the scanner that might be consuming excessive power.
  • Operating in extreme temperatures can reduce battery life.

If these steps do not resolve the issue, please refer to the "Support Information" section.

8. 사양

9. Warranty and Certification

The HBL9100 battery is manufactured with high-quality components and undergoes rigorous testing to ensure reliability.

• 품질 인증: This battery holds ROSH, CE, and UL triple certifications, ensuring compliance with international safety and environmental standards.
• 보호 기능: Built-in protection against over-charge, over-discharge, over-heat, over-current, and short-circuit.
• 보증: The manufacturer provides a warranty that is void if the label is removed or if the battery is disassembled, opened, or serviced by unauthorized personnel. Please refer to the specific warranty terms provided at the time of purchase.

10. 지원 정보

For further assistance or inquiries regarding your HBL9100 Barcode Scanner Battery, please contact the seller or manufacturer through the platform where the purchase was made. When contacting support, please provide your purchase details, including the order number and product model (HBL9100).

For general information about the brand, you may visit the Henhaoro Store on Amazon.