1. 서론
This manual provides essential information for the proper installation, use, and maintenance of your Mopar 68525329AC Semi-Metallic Front Disc Brake Pads. These brake pads are designed to deliver reliable stopping power and durability for compatible vehicles.
2. 안전 정보
경고:
- 브레이크 시스템 관련 작업은 반드시 자격을 갖춘 전문가만 수행해야 합니다. 부적절한 설치는 브레이크 고장 및 심각한 부상 또는 사망으로 이어질 수 있습니다.
- 차량 브레이크 시스템 작업을 할 때는 항상 안전 고글과 장갑을 포함한 적절한 개인 보호 장비(PPE)를 착용하십시오.
- Brake dust may contain hazardous materials. Avoid inhaling dust and use proper disposal methods.
- 작업을 시작하기 전에 차량이 잭 스탠드에 단단히 고정되어 있는지 확인하십시오. 절대로 잭에만 의존하지 마십시오.
- 자세한 토크 사양 및 절차는 차량의 서비스 설명서를 참조하십시오.
3. 패키지 내용
설치를 시작하기 전에 모든 구성 요소가 있고 손상되지 않았는지 확인하세요.
- 2 x Mopar 68525329AC Semi-Metallic Front Disc Brake Pads (set for one axle)
- Brake hardware kit (shims, clips, etc., as applicable)
Figure 1: Contents of the Mopar 68525329AC Brake Pad Kit, showing the brake pads, associated hardware, and the Mopar branded packaging.
4. 설치(Setup)
This section outlines the general procedure for replacing front disc brake pads. Always consult your vehicle's specific service manual for detailed instructions and torque specifications.
- 차량 준비: 차량을 평평한 곳에 주차하고 주차 브레이크를 걸고 뒷바퀴를 고정하십시오. 앞바퀴 휠 너트를 느슨하게 하십시오.
- 들어 올리고 고정하세요: Safely lift the front of the vehicle using a jack and support it securely with jack stands. Remove the front wheels.
- 액세스 캘리퍼: Locate the brake caliper. Depending on your vehicle, you may need to remove two caliper guide pins or bolts to swing the caliper open or remove it entirely.
- 오래된 패드 제거: Carefully slide out the old brake pads from the caliper bracket. Note their orientation.
- 청소 및 검사: Clean the caliper, caliper bracket, and rotor surface thoroughly. Inspect the brake rotor for excessive wear, scoring, or cracks. Replace if necessary. Inspect caliper guide pins and boots for damage.
- 피스톤 압축: Use a brake caliper piston compression tool to slowly and evenly push the caliper piston(s) back into the caliper bore. This creates space for the new, thicker pads.
- 새 하드웨어 설치: Install any new shims, clips, or anti-rattle springs provided in the hardware kit onto the new brake pads or caliper bracket as per your vehicle's manual.
- 새 패드 설치: Carefully slide the new Mopar brake pads into the caliper bracket, ensuring they are correctly seated and oriented.
- 캘리퍼를 재조립하세요: Reinstall the brake caliper over the new pads and rotor. Secure the caliper guide pins or bolts, tightening them to the manufacturer's specified torque.
- 브레이크 블리드(필요한 경우): 브레이크 라인이 열렸거나 시스템에 공기가 들어간 경우 차량 서비스 매뉴얼에 따라 브레이크 시스템의 공기를 빼세요.
- 휠 재설치: Reinstall the wheels and hand-tighten the lug nuts.
- 하부 차량: 차량을 안전하게 지면에 내려놓으십시오.
- 최종 토크: Torque the lug nuts to the vehicle manufacturer's specifications in a star pattern.
- 펌프 브레이크 페달: Before driving, slowly pump the brake pedal several times until a firm pedal feel is achieved. This seats the pads against the rotor and restores hydraulic pressure. Check the brake fluid reservoir level.
5. Bedding-In Procedure (Operating)
Proper bedding-in is crucial for optimal brake performance and longevity. This process transfers a thin, even layer of friction material from the pads to the rotor surface.
- 차량 통행이 적은 안전하고 탁 트인 장소를 찾으세요.
- Perform 10-15 moderate stops from approximately 30-40 mph (50-65 km/h) down to about 5-10 mph (8-16 km/h). Do not come to a complete stop.
- Allow approximately 30 seconds between stops for the brakes to cool slightly.
- After the last stop, drive for several minutes without using the brakes to allow them to cool completely. Avoid hard braking during this cool-down period.
- During the bedding-in process, you may notice some smoke or a burning smell. This is normal.
중요한:
Avoid heavy braking, panic stops, or prolonged braking (e.g., down a long hill) for the first 200-300 miles (320-480 km) after installation to allow the pads to fully seat.
6. 유지관리
- 정기 검사: Inspect brake pads, rotors, and fluid levels regularly as part of your vehicle's recommended maintenance schedule.
- 패드 마모: Replace brake pads when the friction material wears down to the minimum thickness specified by your vehicle manufacturer, typically around 2-3mm.
- 브레이크 오일: Ensure brake fluid is at the proper level and is clean. Consult your vehicle manual for brake fluid replacement intervals.
- 로터 상태: Check rotors for warping, deep grooves, or cracks. Replace or resurface rotors as needed when replacing pads.
7. 일반적인 문제 해결
| 징후 | 가능한 원인 | 해결책 |
|---|---|---|
| 끽끽거리는/갈리는 소음 | New pads not bedded-in, worn pads, foreign object, improper installation, worn rotors. | Perform bedding-in procedure. Inspect pads for wear. Check for debris. Re-install correctly. Inspect/replace rotors. |
| Vibration/Pulsation during braking | Warped rotors, uneven pad transfer, caliper issues. | Inspect/replace rotors. Re-bed pads. Check caliper for sticking. |
| 브레이크 페달이 부드럽거나 푹신한 느낌 | Air in brake lines, low brake fluid, master cylinder issue. | Bleed brake system. Check fluid level and leaks. Consult a mechanic for master cylinder issues. |
8. 사양
- 상표: 모파
- 모델 번호: 68525329AC
- 재료: 반금속
- 자동차 부품 위치: 앞쪽
- 사양 충족: OEM
- 제조업체: 스텔란티스
- 항목 수: 2 (per kit)
9. 보증 정보
Mopar parts are backed by a limited warranty. For specific warranty terms and conditions, please refer to the official Mopar warranty documentation provided with your purchase or visit the official Mopar web사이트. 보증 청구를 위해 구매 증빙 자료를 보관하세요.
10. 고객 지원
For technical assistance, installation questions, or warranty inquiries, please contact your authorized Mopar dealer or visit the official Mopar support web사이트. 자세한 정보와 연락처는 다음에서 확인할 수 있습니다. 아마존의 모파 스토어.
