1. 서론
The ZTW Mantis G2 Series 85A Electronic Speed Controller (ESC) is an advanced 32-bit brushless speed controller designed for high-performance RC airplanes and fixed-wing aircraft. This ESC integrates a powerful 8A adjustable Switching BEC (SBEC) to provide stable power to your receiver and servos. It supports a wide range of battery configurations (3-8S LiPo/LiHV) and offers precise control and reliable operation for your aircraft's propulsion system.
Please read this manual thoroughly before installation and operation to ensure correct usage and maximize the performance and lifespan of your ESC.
2. 안전수칙
Improper use of the ESC can lead to personal injury and damage to the product or associated equipment. Always observe the following safety guidelines:
- 배터리 연결: Always connect the battery with correct polarity. Reverse polarity will cause immediate and irreversible damage to the ESC.
- 격리: 단락을 방지하기 위해 모든 연결부가 적절하게 절연되었는지 확인하십시오.
- 프로펠러 안전: Always remove the propeller from the motor before performing any setup, testing, or maintenance to prevent accidental injury.
- 열: The ESC can generate significant heat during operation. Ensure adequate airflow for cooling and avoid touching it immediately after use.
- 물과 습기: Keep the ESC away from water, moisture, and conductive contaminants.
- 권tag전자 범위: 지정된 입력 볼륨을 초과하지 마십시오tage range (3-8S LiPo/LiHV).
- 어린이들: This product is not a toy and is not suitable for children under 18 years of age without adult supervision.
3. 제품 특징
- Advanced 32-bit microprocessor for precise control and rapid response.
- High-current capability: 85A continuous, 95A burst (10 seconds).
- 넓은 입력 voltage range: Supports 3-8S LiPo/LiHV batteries.
- Integrated 8A adjustable SBEC with selectable output voltages: 6V, 7.4V, or 8.4V.
- Designed specifically for RC airplane and fixed-wing applications.
- Multiple protection features including low-voltage cut-off, overheat protection, and throttle signal loss protection.
- Programmable via ZTW LCD Program Card G2 or dedicated Android/iOS mobile application.
4. 사양
| 매개변수 | 값 |
|---|---|
| 연속 전류 | 85A |
| Burst Current (10S) | 95A |
| 배터리 입력 | 3-8S 리튬폴리머/리튬하이브리드 |
| BEC 출력 | 6V/7.4V/8.4V 조정 가능, 8A |
| 치수(길이*너비*높이) | 88mm * 38mm * 24mm |
| 무게 | 110g |
| 사용자 프로그램 | LCD Program Card G2 / Android & iOS APP |
5. 설정 및 설치
Proper installation is crucial for the safe and efficient operation of your ESC. Follow these steps carefully:
- 모터 연결: Connect the three motor wires (typically labeled A, B, C or U, V, W) from the ESC to the corresponding wires on your brushless motor. The order may affect motor rotation direction; this can be adjusted later if needed.
- 배터리 연결: Connect the main power wires (red for positive, black for negative) from the ESC to your LiPo/LiHV battery. Ensure the connector type matches and polarity is correct.
- 수신기 연결: Plug the throttle signal cable (usually a three-wire servo connector) from the ESC into the throttle channel (typically channel 3) of your RC receiver.
- SBEC 권tage 선택: The Mantis G2 85A ESC features an adjustable SBEC. Refer to the programming section or the dedicated program card/app to set the desired output voltage (6V, 7.4V, or 8.4V) for your receiver and servos. Ensure the selected voltage는 수신기 및 서보와 호환됩니다.
- 설치: Securely mount the ESC in your aircraft, ensuring good airflow for cooling. Avoid mounting it in enclosed spaces without ventilation.
6. 사용 설명서
Before first flight, it is essential to perform a throttle range calibration to ensure the ESC correctly interprets your transmitter's throttle stick positions.
6.1. 스로틀 범위 보정
- 송신기를 켜고 스로틀 스틱을 최대(최대 스로틀) 위치로 설정하십시오.
- 배터리를 ESC에 연결하세요. ESC에서 일련의 신호음이 울릴 것입니다.
- After the initial beeps, the ESC will detect the full throttle signal and emit a confirmation tone.
- Move the throttle stick to its minimum (zero throttle) position. The ESC will emit another series of beeps, indicating the throttle range has been successfully calibrated.
- The ESC is now ready for normal operation.
6.2. 정상 작동
After calibration, connect the battery with the throttle stick at minimum. The ESC will arm, indicated by a specific tone. You can then slowly advance the throttle to control the motor speed. Always ensure the propeller is clear before applying throttle.
7. ESC 프로그래밍
The ZTW Mantis G2 85A ESC offers various programmable parameters to fine-tune its performance to your specific aircraft and preferences. Programming can be done using either the ZTW LCD Program Card G2 or the dedicated Android/iOS mobile application.
7.1. Programmable Parameters (Examp레)
- 브레이크 유형: Off, Soft, Medium, Hard.
- 타이밍: Low, Medium, High (adjusts motor efficiency and temperature).
- 컷오프 볼륨tage: 볼륨을 설정tage at which the ESC reduces or cuts power to protect the battery.
- 시작 모드: Normal, Soft, Super Soft.
- SBEC 권tage: 6V, 7.4V, 8.4V.
- 모터 회전: Normal, Reverse.
Refer to the specific instructions provided with the ZTW LCD Program Card G2 or within the mobile application for detailed steps on how to connect and adjust these parameters.
8. 유지관리
Regular inspection and basic maintenance will help ensure the longevity and reliable performance of your ESC:
- 청소: Keep the ESC free from dust, dirt, and debris. Use a soft brush or compressed air to clean the heat sink fins.
- 연결 확인: Periodically inspect all wire connections (motor, battery, receiver) for signs of wear, corrosion, or loose contacts.
- 물리적 손상: Check the ESC casing and wires for any physical damage after each flight.
- 저장: ESC를 직사광선과 극한의 온도를 피해 건조하고 서늘한 환경에 보관하세요.
9. 문제 해결
If you encounter issues with your ZTW Mantis G2 85A ESC, refer to the following common problems and solutions:
- 모터가 회전하지 않음:
- 배터리 연결 및 충전 수준을 확인하세요.
- Verify throttle signal cable is securely connected to the receiver.
- Perform throttle range calibration again.
- Ensure motor wires are correctly connected and not shorted.
- 모터가 잘못된 방향으로 작동합니다.
- ESC와 모터 사이에 있는 세 개의 모터 배선 중 두 개를 서로 바꿔 연결하세요.
- Alternatively, reverse motor direction using the programming options.
- ESC Overheats:
- ESC 주변에 적절한 공기 흐름이 유지되도록 하세요.
- Check if the propeller is too large or motor timing is too aggressive (adjust via programming).
- 배터리 용량 확인tage and current draw are within specifications.
- Intermittent Power/Loss of Control:
- 모든 연결부가 헐거워지거나 부식되었는지 확인하십시오.
- Inspect for damaged wires or solder joints.
- Ensure receiver and transmitter are functioning correctly and within range.
10. 보증 및 지원
For warranty information and technical support regarding your ZTW Mantis G2 Series 85A ESC, please contact the retailer or the manufacturer, ZTW, directly. For purchases made through Buddy RC, please reach out to Buddy RC customer service for assistance.
구매 영수증을 보관하여 보증 청구에 대비하세요.
