1. 제품 오버view
The ProCom Heating ML250TPA-B is a 25,000 BTU Liquid Propane Ventless Infrared Plaque Heater designed to provide efficient heating for indoor spaces up to 1150 sq. ft. This heater features a thermostat control for adjustable heat settings and can be used with included base feet for floor placement or mounted on a wall.
이미지 1.1: 앞면 view of the ProCom ML250TPA-B heater with base feet.
주요 특징:
- 25,000 BTU Output: Heats areas up to 1150 sq. ft.
- 통풍구 없는 디자인: No chimney or flue required.
- Infrared Plaque Heating: Provides radiant heat.
- 온도 조절 장치 제어: High/Medium/Low settings for precise temperature management.
- Push Button Ignition: For easy startup.
- 산소 고갈 센서(ODS): Automatically shuts off the heater if oxygen levels drop.
- 유연한 설치: Includes base feet for floor standing and hardware for wall mounting.
- 전기가 필요 없습니다: Operates independently of electrical power, ideal for outag에스.
2. 안전 정보
경고: 부적절한 설치, 조정, 변경, 서비스 또는 유지보수는 재산 피해, 부상 또는 사망을 초래할 수 있습니다. 이 장비를 설치하거나 서비스하기 전에 설치, 작동 및 유지보수 지침을 철저히 읽으십시오.
- This is a ventless appliance. It uses air from the room in which it is installed. Provisions for adequate combustion and ventilation air must be provided.
- Always ensure proper ventilation when operating this heater. Consider using a carbon monoxide detector for added safety.
- 이 기기나 다른 기기 근처에서 가솔린이나 기타 가연성 증기 및 액체를 보관하거나 사용하지 마십시오.
- 히터 주변을 깨끗하게 유지하고 가연성 물질, 휘발유 및 기타 인화성 증기 및 액체가 없도록 하십시오.
- Never operate the heater in an area where it may be exposed to water.
- The Oxygen Depletion Sensor (ODS) is a safety feature that will shut off the heater if oxygen levels in the room become too low. Do not tamper with or bypass this safety device.
- Ensure the heater is installed on a level, stable surface if using base feet, or securely mounted to a wall according to instructions.
- Keep children and pets away from the heater, especially during operation, as surfaces can become very hot.
3. 설정 및 설치
3.1 풀기 및 검사
Carefully remove the heater from its packaging. Inspect the unit for any shipping damage. If any damage is found, do not attempt to install or operate the heater. Contact your retailer or ProCom customer service immediately.
3.2 위치 선택
Select a location that is clear of combustible materials. Ensure adequate clearance from walls and furniture as specified in the full manual. This heater is designed for indoor use only.
3.3 Assembly (Base Feet or Wall Mount)
The heater comes with both base feet for floor placement and hardware for wall mounting. Choose the installation method that best suits your needs.
Image 3.1: The heater package includes base feet and a wall bracket for flexible installation.
- For Floor Standing: Attach the provided base feet to the bottom of the heater using the supplied screws. Ensure the heater is stable and level.
- 벽 장착용: Use the included wall bracket and hardware to securely mount the heater to a suitable wall surface. Follow the detailed instructions in the complete manual for proper wall mounting to ensure stability and safety.
이미지 3.2: Example of the ProCom ML250TPA-B heater installed on a wall.
3.4 Propane Gas Connection
This heater operates on Liquid Propane (LP) gas. Connection to the LP supply must be performed by a qualified service person in accordance with local codes and ordinances. The heater does not require electricity for operation.
- A 3/8" Flare x 3/8" NPT Male brass 90-degree elbow and a 12 FT Propane Regulator Hose with a female flare nut end may be required for connecting to a 20 lb propane tank, especially if using the base feet to ensure proper clearance and prevent kinking of the hose.
- Ensure all connections are tight and leak-free. Perform a leak test with a soap solution before initial operation.
4. 사용 설명서
4.1 제어판 이상view
Image 4.1: The control panel features a Piezo Ignition button and a thermostat knob with variable heat settings.
The heater features a simple control panel with a Piezo Ignition button and a thermostat control knob. The thermostat knob allows you to select heat settings from "OFF PILOT" to various heat levels (e.g., 1-5 or High/Medium/Low).
4.2 Initial Startup Procedure
IMPORTANT: For the very first use, or after the heater has been disconnected from the propane supply for an extended period, the initial ignition may take longer than usual. This is normal as air needs to be purged from the gas lines.
- Ensure the propane supply valve is fully open.
- Turn the thermostat control knob to the "PILOT" position.
- Press and hold the thermostat control knob down firmly.
- While holding the knob down, repeatedly press the Piezo Ignition button until the pilot flame ignites. You may need to hold the knob down for several minutes (up to 10 minutes for the very first startup) to allow gas to reach the pilot.
- Once the pilot flame is lit, continue to hold the thermostat control knob down for approximately 30-60 seconds to allow the thermocouple to heat up and hold the pilot flame.
- Release the knob. If the pilot flame extinguishes, repeat steps 3-5.
- Once the pilot flame is stable, turn the thermostat control knob to your desired heat setting (e.g., 3, 4, 5, or High/Medium/Low). The main burner will ignite.
NOTE: It is recommended to perform the first ignition outdoors or in a well-ventilated area, as a thin oil layer on internal components may burn off, causing a temporary odor or light smoke.
4.3 열 출력 조절
Rotate the thermostat control knob to adjust the heat output. Higher numbers or "High" settings will provide more heat, while lower numbers or "Low" settings will reduce the heat output. The heater will cycle on and off to maintain the set temperature.
Video 4.2: A demonstration of the ProCom Natural Gas Ventless Infrared Plaque Heater, highlighting its features and operation. Note: This video shows a natural gas model, but the operational principles for ignition and thermostat control are similar for the propane model.
5. 유지관리
Regular maintenance ensures the safe and efficient operation of your ProCom heater. Always disconnect the heater from the propane supply and allow it to cool completely before performing any maintenance.
- 청소: Keep the exterior of the heater clean. Use a soft, damp 천으로 표면을 닦으세요. 연마성 세제나 용제는 사용하지 마세요. 공기 흡입구와 배출구에 먼지나 이물질이 없는지 확인하세요.
- 파일럿 버너 및 버너 점검: Periodically inspect the pilot and main burner for any obstructions or unusual flame patterns. If the pilot flame appears weak or yellow, or if the main burner flames are not blue, contact a qualified service technician.
- 가스 배관 점검: Regularly check the gas supply line and connections for any signs of wear, damage, or leaks.
- 저장: If storing the heater for an extended period, disconnect it from the propane supply, clean it thoroughly, and store it in a dry, safe place.
6. 문제 해결
고객 서비스에 연락하기 전에 다시view 다음은 일반적인 문제와 해결 방법입니다.
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| Heater does not ignite or pilot light won't stay lit. |
|
|
| Heater produces an odor or light smoke on first use. | Protective oil coating burning off. | This is normal for initial operation. Ensure good ventilation. Odor/smoke should dissipate quickly. |
| Control knob does not function correctly at low settings (e.g., 1 or 2). | Possible manufacturing tolerance or design characteristic. | Ensure the knob is set to a position where the burner reliably ignites (e.g., 3 or higher). If persistent, contact customer support. |
| Heater makes a weird noise during ignition. | Intermittent ignition issue or gas flow problem. | Ensure gas supply is stable. If noise persists or ignition is unreliable, contact a qualified technician. |
7. 사양
| 상표 | ProCom |
| 모델 번호 | ML250TPA-B |
| 연료 유형 | 액체 프로판 |
| BTU 출력 | 25,000비티유 |
| 난방 범위 | 최대 1150제곱피트 |
| 특징 | Overheat Protection, Oxygen Depletion Sensor (ODS) |
| 색상 | 하얀색 |
| 폼 팩터 | Pedestal (with base feet) |
| 실내/실외 사용 | 실내 |
| 제품 크기(D x W x H) | 8인치 깊이 x 26.63인치 너비 x 23.5인치 높이 |
| 장착 유형 | 바닥 장착, 벽면 장착 |
| 속도의 수 | 3 (High/Medium/Low thermostat settings) |
| 최저 온도 설정 | 화씨 40도 |
| 품목 무게 | 34.6파운드 |
| 한국어: | 848660008338 |
8. 보증 및 지원
For warranty information, please refer to the documentation included with your product or visit the official ProCom web해당 사이트입니다. 보증 청구를 위해서는 구매 증빙 자료를 보관하는 것이 중요합니다.
Note on Warranty Claims: Some warranty processes may require specific documentation, such as a professional pressure reading of your propane system, to validate claims. Please review the warranty terms carefully.
For technical assistance, replacement parts, or further inquiries, please contact ProCom customer service through their official channels.
