IRRADIO Simplified Universal Remote Control with Learning Function

1. 서론

This manual provides detailed instructions for the setup, operation, and maintenance of your IRRADIO Simplified Universal Remote Control. This remote is designed for ease of use, featuring a learning function to replicate commands from your original remote control. Its simplified layout and large buttons make it suitable for users of all ages.

2. 제품 오버view

The IRRADIO Simplified Universal Remote Control is an infrared remote with a minimalist design. It features essential buttons for common functions, making it straightforward to operate.

이미지 2.1: 앞쪽 view of the IRRADIO Simplified Universal Remote Control. It features large, clearly labeled buttons for power, volume, channel, and two programmable auxiliary buttons (A and B).

버튼 기능:

• 전원 버튼(빨간색): 장치를 켜거나 끕니다.
• AV Button (Mute): Toggles audio mute or switches AV input (programmable).
• V+ / V-: 볼륨을 늘리거나 줄입니다.
• P+ / P-: 채널을 위아래로 변경합니다.
• A/B 버튼: Two additional programmable buttons for frequently used functions.
• Indicator LED (Red dots): Lights up during button press and programming.

3. 설정: 배터리 설치

The remote control requires 2x AAA/LR03 1.5V batteries (not included).

1. 리모콘 뒷면에서 배터리함을 찾으세요.
2. 배터리실 커버를 밀어서 엽니다.
3. Insert two AAA/LR03 batteries, ensuring the correct polarity (+ and -) as indicated inside the compartment.
4. 배터리 덮개를 단단히 닫으세요.

메모: The remote retains programmed memory even after battery replacement.

4. Operating Instructions: Programming the Remote Control

This universal remote uses a learning function to copy signals from your original remote control. You will need a functional original remote for programming.

프로그래밍 단계:

1. 준비: Place the IRRADIO universal remote and your original remote control on a flat surface, facing each other, with their infrared emitters aligned at a distance of approximately 1-3 cm.
2. 학습 모드로 들어가기: 를 누르고 계세요 힘 버튼과 AV button simultaneously on the IRRADIO remote for about 3 seconds. The red indicator LED will light up continuously, indicating the remote is in learning mode.
3. 프로그래밍할 버튼을 선택하세요: Press the button on the IRRADIO remote that you wish to program (e.g., V+, P+, A, B). The red indicator LED will start blinking slowly, waiting for a signal.
4. 신호 전송: Press and hold the corresponding button on your original remote control (e.g., Volume Up, Channel Up). Keep holding it until the IRRADIO remote's LED blinks rapidly three times and then lights up continuously again. This indicates successful learning.
5. 버튼 추가 프로그래밍: Repeat steps 3 and 4 for each button you wish to program.
6. 학습 모드 종료: 원하는 버튼을 모두 프로그래밍했으면 버튼을 누르십시오. 힘 button on the IRRADIO remote to exit learning mode. The red indicator LED will turn off.

중요 참고 사항:

• If the LED does not blink rapidly or turns off during programming, the learning process may have failed. Try again, ensuring proper alignment and battery levels in both remotes.
• Ensure the original remote has sufficient battery power for signal transmission.
• The remote can be reprogrammed infinitely.

5. 유지관리

배터리 교체:

When the remote control's response becomes sluggish or the indicator LED does not light up, it is time to replace the batteries. Follow the battery installation steps in Section 3.

청소:

To clean the remote control, use a soft, dry cloth. Do not use abrasive cleaners, solvents, or wet cloths, as these can damage the surface or internal components.

6. 문제 해결

• 리모컨이 응답하지 않음:
  • 배터리가 올바른 극성으로 올바르게 삽입되었는지 확인하세요.
  • Replace old batteries with new AAA/LR03 batteries.
  • 리모컨과 장치 사이에 장애물이 없는지 확인하세요.
• Learning function fails:
  • Ensure the original remote control is working and has sufficient battery power.
  • Verify that the IRRADIO remote and the original remote are aligned correctly, facing each other at a close distance (1-3 cm).
  • Make sure you are pressing and holding the buttons for the required duration during programming.
  • Try programming in a room with less ambient light, as strong light sources can sometimes interfere with IR signals.
• Programmed button does not work:
  • The learning process might not have been successful for that specific button. Repeat the programming steps for that button.
  • Ensure the original remote's signal was strong and clear during programming.

7. 사양

8. 보증 및 지원

For warranty information or technical support, please refer to the contact details provided with your purchase or visit the official Irradio web사이트. 보증 청구를 위해 구매 증빙 자료를 보관하세요.