소개
This manual provides detailed instructions for the setup, operation, and maintenance of your Mebus Electronic Alarm Clock, Model 785871. Please read this manual thoroughly before using the device to ensure proper function and longevity.
The Mebus Electronic Alarm Clock is a digital, radio-controlled device designed to provide accurate time, date, and temperature readings, along with reliable alarm functions. Its modern design and clear display make it suitable for various room types, especially bedrooms.
패키지 내용
- Mebus Electronic Alarm Clock (Model 785871)
- 사용 설명서 (본 문서)
참고: 배터리는 포함되어 있지 않으므로 별도로 구매해야 합니다.
설정
1. 배터리 설치
- 알람 시계 뒷면에서 배터리 덮개를 찾으세요.
- 덮개를 밀거나 풀어서 수납 공간을 엽니다.
- Insert the required batteries (e.g., 2 x AAA) according to the polarity indicators (+ and -) inside the compartment.
- 배터리함 덮개를 단단히 다시 닫으십시오.
Important: Ensure correct battery polarity to prevent damage to the device.
2. Initial Power On and Radio Controlled Time Synchronization
Upon battery installation, the clock will power on and automatically begin searching for the radio time signal. This process may take several minutes to an hour, depending on your location and signal strength.
- Place the clock near a window or in an open area for optimal signal reception.
- A signal icon (often a radio tower or wave symbol) on the display will flash during synchronization and become solid once the time is successfully set.
- If synchronization fails, the clock will typically default to a standard time (e.g., 12:00 AM) and you may need to set the time manually (see "Setting Time Manually" in the Operating section).
그림 1: 전면 view of the Mebus Electronic Alarm Clock, showing the digital display with time, date, day, and temperature, along with control buttons.
작동 지침
1. 버튼 오버view
The clock features several buttons for control. The main buttons are typically:
- SET 버튼: Used to enter setting modes for time, alarm, etc. There are two 'SET' buttons, likely for different functions or for confirming settings.
- MODE 버튼: Cycles through display modes or setting options.
- ▲ / ▼ buttons: Adjust values (increase/decrease) during setting modes.
그림 2: 각도 view of the Mebus Electronic Alarm Clock, highlighting the arrangement of the control buttons below the digital display.
2. Setting Time Manually (if radio control is unavailable)
- Press and hold the appropriate 세트 button (refer to specific button labels on your device, often labeled "TIME SET" or similar) until the time display flashes.
- 사용하세요 ▲ 그리고 ▼ 시간을 조정하는 버튼입니다.
- 를 누르세요 세트 button again to move to minutes, then use ▲ 그리고 ▼ 조정하다.
- 계속 누르기 세트 to cycle through other settings like year, month, and day, adjusting each with ▲ 그리고 ▼.
- 를 누르세요 세트 button one last time or wait a few seconds for the clock to exit setting mode.
3. 알람 설정
- 를 누르고 계세요 세트 button associated with the alarm function (often indicated by an alarm icon or "ALARM SET"). The alarm time will flash.
- 사용하세요 ▲ 그리고 ▼ 원하는 알람 시간을 설정하는 버튼입니다.
- 알람을 누르세요 세트 button again to move to minutes, then use ▲ 그리고 ▼ 조정하다.
- 알람을 누르세요 세트 button one last time or wait for the clock to exit setting mode.
- To activate/deactivate the alarm, there is usually a dedicated switch or button (often on the side or back, or a quick press of an alarm SET button). Look for an alarm icon on the display to confirm activation.
4. 스누즈 기능
When the alarm sounds, press the large button on the top of the clock (if present, or a designated snooze button) to activate the snooze function. The alarm will temporarily stop and sound again after a few minutes (typically 5-10 minutes). To turn off the alarm completely, press any other button or flip the alarm switch off.
5. Display Modes and Temperature Unit Selection
- 디스플레이 모드 : 를 누르세요 방법 button to cycle through different display information, such as time, date, and potentially other features.
- 온도 단위 : To switch between Celsius (°C) and Fahrenheit (°F) for the temperature display, locate a small button or switch, often on the back or side of the unit, or it might be an option within the 방법 설정.
유지
1. 청소
- 시계 외부를 부드럽고 마른 천으로 닦으세요.
- Do not use abrasive cleaners, solvents, or chemical sprays, as these can damage the finish or electronic components.
- 어떠한 구멍에도 습기가 들어가지 않도록 주의하세요.
2. 배터리 교체
- When the display dims or functions become erratic, it is time to replace the batteries.
- Follow the "Battery Installation" steps in the Setup section.
- 현지 규정에 따라 오래된 배터리를 책임감 있게 폐기하십시오.
문제 해결
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| 디스플레이가 비어 있거나 어둡습니다. | 배터리가 부족하거나 방전되었습니다. | 배터리를 새 배터리로 교체하십시오. 극성을 반드시 확인하십시오. |
| 시간이 잘못되었거나 동기화가 되지 않습니다. | Poor radio signal reception; manual time not set correctly. | Move the clock to a location with better signal (e.g., near a window). Allow time for synchronization. If persistent, set time manually. |
| 알람이 울리지 않습니다. | Alarm is not activated; alarm time not set correctly. | Ensure the alarm function is turned on (check for alarm icon on display). Verify the alarm time is set as desired. |
| 버튼이 반응하지 않습니다. | Temporary software glitch; very low batteries. | Remove and reinsert batteries to perform a soft reset. Replace batteries if they are old. |
명세서
- 상표: 메부스
- 모델 번호: 785871 (also known as Mebus 25800)
- 디스플레이 유형: 디지털
- 스타일: 현대의
- 특징: 경보
- 전원: 배터리 작동식 (배터리는 포함되어 있지 않습니다)
- 객실 유형: 침실
- 모양: Square-ish
- 재료: 플라스틱
- 치수: 5.12 x 2.95 x 2.13인치(패키지 크기)
- 품목 무게: 4.9 온스
지원하다
For further assistance or inquiries not covered in this manual, please refer to the Mebus official website or contact their customer support. Keep your product model number (785871) handy when seeking support.
Note: Specific contact details are not provided in this document.
