Xnbada RC03RF Wireless 2.4G RF 4 Zone RGB RGBW RGBCCT Smart Remote Control User Manual

1. 서론

This manual provides detailed instructions for the Xnbada RC03RF Wireless 2.4G RF 4 Zone Smart Remote Control. This remote is designed to control RGB, RGBW, and RGBCCT LED strip lights, offering versatile lighting adjustments through its 2.4G RF technology.

패키지 내용:

• 1 x RC03RF Remote Control
• 2 x 나사(벽면 장착용)

Figure 1: Xnbada RC03RF Remote Control and mounting screws.

2. 사양

3. 설정

3.1 배터리 설치

1. 리모콘 뒷면에서 배터리함을 찾으세요.
2. 배터리 덮개를 엽니다.
3. 올바른 극성(+/-)을 확인하여 AAA 배터리 2개(2)를 삽입합니다.
4. 배터리 덮개를 단단히 닫으세요.

참고: 배터리는 포함되어 있지 않으므로 별도로 구매해야 합니다.

3.2 Pairing with Controllers

The RC03RF remote uses 2.4G RF technology for quick pairing without the need for Wi-Fi, Bluetooth, or a gateway. The pairing process typically involves the following steps:

1. Ensure your compatible LED controller (e.g., C03W, C04W, C05W) is powered on and connected to your LED strip lights.
2. On the LED controller, locate the pairing button (often labeled 'SET' or 'PAIR'). Press and hold this button for a few seconds until the connected LED strip lights flash or indicate pairing mode.
3. Within 15 seconds of the controller entering pairing mode, press one of the Zone ON buttons (1, 2, 3, or 4) on the RC03RF remote control.
4. The LED strip lights should flash again, indicating successful pairing.
5. Repeat this process for each zone you wish to control with a separate controller, or for multiple controllers within the same zone.

Figure 2: The RC03RF remote can control multiple LED strip controllers, with each zone button managing a distinct group of lights.

Figure 3: The remote control signal can be automatically transmitted to other controllers within 30 meters, extending the control range.

4. 사용 설명서

4.1 리모컨 레이아웃 및 기능

Figure 4: RC03RF Remote Control Button Functions.

• 에: Press to turn ON all linked devices.
• OFF : Press to turn OFF all linked devices.
• 색상 링: Touch the slider to select from 16 million colors and dim brightness from 1% to 100%.
• W: Press to switch between cool white, nature white, and warm white repeatedly.
• M(모드): Press to cycle through dynamic modes.
• 밝기 높이기/낮추기: 밝기를 높이거나 낮추려면 누릅니다.
• Color Temp/Saturation Up/Down: Press to adjust color temperature or saturation.
• S-/S+ (Speed): Lower or accelerate dynamic mode speed.
• 구역 켜짐/꺼짐(1-4): Press to turn ON/OFF specific zones or activate night light mode for a zone.

4.2 색상 및 밝기 조정

• 색상 선택: Use the central color ring to select any of 16 million colors.
• 밝기 조절: Adjust the brightness from 0% to 100% using the dedicated brightness buttons or by sliding on the color ring.
• 백색광 조절: Press the 'W' button to cycle through different white light temperatures (cool, natural, warm).
• 7 Pure Colors: The remote allows for one-key switching between 7 pure colors (red, orange, yellow, green, blue, purple, white).

Figure 5: Utilize the touch color ring for precise color selection from 16 million options.

Figure 6: Adjust brightness levels from 0% to 100% and activate night light mode.

Figure 7: Fine-tune the lighting with color temperature and saturation adjustments.

4.3 구역 제어

The RC03RF remote allows you to control up to four independent zones of LED lights. Each zone can be controlled individually or grouped together.

• 개별 구역 제어: Press the corresponding Zone ON/OFF button (1, 2, 3, or 4) to control lights in that specific zone.
• All Zones Control: Use the Master ON/OFF buttons to control all paired zones simultaneously.

Figure 8: Manage lighting in up to four separate zones with dedicated buttons.

4.4개의 다이내믹 모드

The remote includes various dynamic lighting modes. Press the 'M' button to cycle through these modes. Use the 'S-' and 'S+' buttons to adjust the speed of the selected dynamic mode.

5. 호환성

The RC03RF remote control is compatible with the following Xnbada LED controllers:

• C03W (RGB Controller)
• C03Z (RGB Controller)
• C04W (RGBW Controller)
• C04Z (RGBW Controller)
• C05W (RGBCCT Controller)
• C05Z (RGBCCT Controller)
• WB5
• LM052
• LM053
• LM051

It is designed to control various LED strip light types, including COB, 5630, 5050, 3014, 5730, and 3528 LED strips.

Figure 9: A selection of compatible Xnbada LED controllers.

6. 유지관리

6.1 청소

To clean the remote control, use a soft, dry cloth. Avoid using abrasive cleaners, solvents, or harsh chemicals, as these can damage the surface or internal components.

6.2 배터리 교체

When the remote's performance degrades or it stops responding, replace the two AAA batteries. Ensure proper polarity during installation.

6.3 보관

리모컨은 직사광선과 극한 온도 변화를 피해 서늘하고 건조한 곳에 보관하십시오. 장기간 보관할 경우 누액 방지를 위해 배터리를 제거하십시오.

7. 문제 해결

• 리모컨이 응답하지 않음:
  Check if the batteries are correctly installed and have sufficient charge. Replace batteries if necessary. Ensure the remote is within the 30-meter operating range of the controller. Re-pair the remote with the controller if the connection is lost.
• LEDs flickering:
  This can sometimes be caused by an unstable power supply to the LED controller. Ensure your power adapter provides stable voltage and sufficient current for your LED strips.
• 제한된 제어 범위:
  Obstacles such as thick walls or metal structures can reduce the effective range. Ensure there are no major obstructions between the remote and the controller. Minimize interference from other 2.4Ghz devices.
• Incorrect color display:
  Verify that the LED strip type (RGB, RGBW, RGBCCT) matches the controller and that the remote is correctly paired for that specific type.

8. 보증 및 지원

For warranty information and technical support, please refer to the product packaging or contact Xnbada customer service directly. Keep your purchase receipt for warranty claims.