1. 제품 오버view
The Parkside PDOS 200 C2 Double Grinder is a versatile power tool designed for grinding, sharpening, deburring, and derusting various metal and steel workpieces. It features a quiet, maintenance-free induction motor and two grinding wheels for both coarse and fine applications. This manual provides essential information for safe operation, setup, maintenance, and troubleshooting.
이미지 1.1: The Parkside PDOS 200 C2 Double Grinder. This image shows the complete unit from a slight angle, highlighting its two grinding wheels, protective covers, and the central motor housing with the power switch.
2. 안전 지침
감전, 화재 및 심각한 부상을 예방하려면 항상 다음 안전 예방 조치를 준수하세요.
- 매뉴얼을 읽어보세요: Before operating the grinder, read and understand all instructions and safety warnings.
- 개인 보호 장비(PPE): 항상 보안경이나 안면 보호대, 청력 보호구, 그리고 적절한 작업용 장갑을 착용하십시오.
- 작업 영역: 작업 공간은 깨끗하고 밝으며 물건이 어지럽게 널려 있지 않도록 하십시오. 적절한 환기를 확보하십시오.
- 전기 안전: Ensure the power supply matches the grinder's specifications. Do not operate in damp 또는 습한 환경.
- 안전한 작업물: Always hold the workpiece firmly against the work rest.
- 경비 유지: Never operate the grinder without the protective covers and spark guards properly installed and adjusted.
- 과도한 확장을 피하세요: 항상 적절한 발판과 균형을 유지하십시오.
- 사용하지 않을 때는 플러그를 뽑아두세요: Disconnect the grinder from the power supply before making adjustments, changing accessories, or when not in use.
- 사용 전 검사: 손상된 부품, 정렬 불량 또는 작동에 영향을 줄 수 있는 기타 문제가 있는지 확인하십시오.
3. 패키지 내용
Carefully unpack all items and check for completeness. If any parts are missing or damaged, contact customer support.
- Parkside PDOS 200 C2 Double Grinder unit
- 1x Coarse grinding wheel (Grit 36)
- 1x Fine grinding wheel (Grit 80)
- 2x Spark protection glasses
- 2x Work rests
- Mounting hardware (if applicable for bench mounting)
- 사용 설명서
4. 설정
4.1 Bench Mounting
For stable and safe operation, the double grinder should be securely mounted to a workbench. Use appropriate bolts and nuts (not always included) to fasten the grinder through the mounting holes in its base.
4.2 Installing Spark Protection Glasses and Work Rests
- Attach the spark protection glasses to the designated brackets above each grinding wheel. Ensure they are securely fastened and positioned to protect your eyes from sparks and debris.
- Install the work rests in front of each grinding wheel. Adjust their position so that the gap between the work rest and the grinding wheel is no more than 2 mm. This gap should be maintained as the wheel wears down. The work rests are tool-free adjustable.
이미지 4.1: 앞쪽 view of the grinder, showing the spark protection glasses and adjustable work rests in position. The image also depicts sparks generated during grinding, illustrating the function of the protective elements.
4.3 전원 연결
Connect the power cable to a suitable electrical outlet. Ensure the power switch is in the "OFF" position before plugging in the unit.
5. 사용 설명서
5.1 켜기/끄기
- To turn on the grinder, press the dust-protected ON (I) switch.
- To turn off the grinder, press the OFF (O) switch.
- Allow the grinding wheels to reach full speed before beginning work.
5.2 연삭 기술
The PDOS 200 C2 features two grinding wheels:
- Coarse Grinding Wheel (Grit 36): Use for rapid material removal, shaping, and initial sharpening of dull tools.
- Fine Grinding Wheel (Grit 80): Use for finishing, fine sharpening, and deburring.
When grinding:
- Always wear appropriate PPE.
- Hold the workpiece firmly against the work rest.
- Apply light, even pressure. Excessive pressure can damage the wheel or motor.
- Move the workpiece across the face of the wheel to ensure even wear.
- Avoid grinding on the side of the wheel, as this can cause the wheel to break.
- 연마할 때는 휠에 대해 일정한 각도를 유지하십시오.
- Allow the workpiece to cool periodically to prevent overheating and damage to the material.
6. 유지관리
정기적인 유지보수는 분쇄기의 수명 연장과 안전한 작동을 보장합니다.
- 청소: Disconnect from power. Use a brush or compressed air to remove dust and debris from the motor housing and around the wheels.
- 휠 검사: Regularly inspect grinding wheels for cracks, chips, or excessive wear. Replace damaged or worn wheels immediately.
- Work Rest Adjustment: Ensure the gap between the work rest and the grinding wheel remains at a maximum of 2 mm. Adjust as the wheel wears.
- Spark Guard Inspection: Check spark protection glasses for cracks or excessive scratching that may impair visibility. Replace if necessary.
- 모터: The induction motor is maintenance-free and does not require lubrication.
7. 문제 해결
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| 그라인더가 시작되지 않습니다. | No power supply; Power switch off; Faulty power cable. | Check power connection; Ensure switch is ON; Inspect cable for damage. |
| 과도한 진동. | Unbalanced grinding wheel; Loose mounting; Damaged wheel. | Check wheel for balance and damage; Ensure grinder is securely mounted; Replace damaged wheel. |
| Grinding wheel wears quickly. | Excessive pressure; Incorrect wheel for material. | Apply lighter pressure; Ensure appropriate wheel grit is used. |
8. 사양
| 모델: | PDOS 200 C2 |
| Power Input (S2 30 min): | 200와트 |
| Power Input (S1): | 145와트 |
| 무부하 속도: | 2980분⁻¹(RPM) |
| 연삭 휠 직경: | 15cm |
| Grinding Wheel Width: | 20mm (XNUMXmm) |
| Grinding Speed: | 23m/초 |
| 모래: | 36 (Coarse) / 80 (Fine) |
| 재료: | 합금강, 알루미늄 |
| 전원 케이블 길이: | 2분 |
| 무게: | 약 4.65kg |
| 제조업체: | 크리빗 |
| 제품 모델 번호: | 65445일 |
9. 보증 및 지원
This product comes with a standard manufacturer's warranty. Please refer to the warranty card included with your purchase for specific terms and conditions. For technical support, spare parts, or warranty claims, please contact your retailer or the manufacturer's customer service department.
보증을 위해 구매 증빙서류로 구매 영수증을 보관하세요.
