소개
This manual provides comprehensive instructions for the installation, operation, and maintenance of your Ecolink WST-232 Wireless Home Security Door Window Sensor. This device is designed to enhance the security of your home by detecting the opening and closing of doors and windows. It is compatible with Honeywell 5800 Wireless and 2GIG security systems.
중요한 안전 정보
- 설치 및 사용 전에 모든 지침을 주의 깊게 읽으십시오.
- Do not attempt to repair or modify the sensor. Refer all servicing to qualified personnel.
- 배터리는 어린이의 손이 닿지 않는 곳에 보관하십시오. 사용한 배터리는 지역 규정에 따라 올바르게 폐기하십시오.
- Ensure the sensor is installed in a location where it will not be exposed to extreme temperatures or moisture.
패키지 내용
패키지에 모든 품목이 들어 있는지 확인하세요.
- Ecolink WST-232 Wireless Door/Window Sensor (Main Unit)
- Magnet (for contact detection)
- 설치용 하드웨어(나사, 접착 테이프)
- Interchangeable Brown Case
- 사용 설명서 (본 문서)
제품 끝view
The Ecolink WST-232 is a compact wireless sensor designed for monitoring the open/closed status of doors and windows. It features an internal reed switch for standard magnetic contact detection and an external contact input for connecting wired devices.
영상: Ecolink WST-232 Wireless Door/Window Sensor showing the main unit and the external contact wires.
주요 구성 요소:
- 메인 센서 유닛: Contains the battery, wireless transmitter, and internal reed switch.
- 자석 : Triggers the internal reed switch when separated from the main unit.
- External Contact Input: Two wires (typically red and black) for connecting an external wired contact.
- 배터리 칸: 본체 뒷면에 위치해 있습니다.
설정 및 설치
1. 배터리 설치
- 센서 c를 엽니다asing by gently prying it open from the side notch.
- Insert the CR2032 lithium battery, ensuring the positive (+) side faces up.
- 센서 c를 닫으세요asing 안전하게.
2. Enrolling the Sensor with Your Security Panel
The WST-232 sensor is compatible with Honeywell 5800 Wireless and 2GIG security systems. Refer to your security panel's manual for specific enrollment procedures. General steps are as follows:
- Put your security panel into programming mode for adding new wireless zones.
- Activate the sensor by separating the magnet from the main unit, or by connecting/disconnecting the external contact wires. This sends a signal to the panel.
- Confirm the sensor's serial number is learned by the panel.
- Assign the sensor to an appropriate zone type (e.g., "Entry/Exit," "Perimeter").
- Exit programming mode on your panel.
3. 센서 장착
Choose a suitable location on your door or window frame. The sensor and magnet should be mounted within 0.5 inches (1.27 cm) of each other when the door/window is closed.
영상: Ecolink WST-232 sensor components including the main unit, magnet, and mounting screws.
나사 사용:
- Position the main sensor unit on the stationary frame and the magnet on the moving part (door/window).
- 나사 구멍을 표시하십시오.
- 필요한 경우 시험용 구멍을 뚫습니다.
- Secure both the sensor and magnet with the provided screws.
Using Adhesive Tape (not recommended for long-term security):
- Clean the mounting surfaces thoroughly.
- Apply adhesive tape to the back of the sensor and magnet.
- Press firmly onto the desired surfaces for at least 30 seconds.
4. External Contact Input
The WST-232 includes an external contact input for integrating other wired devices, such as recessed door contacts or pressure mats. Connect the two wires from your external device to the red and black wires of the WST-232 sensor. The sensor will transmit a signal when the external contact opens or closes.
센서 작동
Once installed and enrolled, the Ecolink WST-232 sensor operates automatically. When the door or window it is monitoring opens, separating the magnet from the main unit (or opening the external contact), the sensor will transmit a signal to your security panel. This signal indicates an "open" state. When the door or window closes, bringing the magnet back into proximity (or closing the external contact), the sensor transmits a "closed" state signal.
Your security panel will then react according to its programming (e.g., trigger an alarm if the system is armed, log the event).
유지
배터리 교체
The sensor uses one CR2032 lithium battery. When the battery level is low, your security panel will typically display a low battery warning for the corresponding zone. To replace the battery:
- Put your security panel into disarm or test mode to prevent false alarms.
- 센서 c를 살짝 열어주세요asing.
- 기존 CR2032 배터리를 제거하세요.
- 새 CR2032 배터리를 넣을 때 극성(+극이 위로 향하도록)을 확인하십시오.
- 센서 c를 닫으세요asing 안전하게.
- Test the sensor to ensure it communicates with the panel.
청소
Clean the sensor and magnet with a soft, dry cloth. Do not use liquid cleaners or abrasive materials, as these can damage the device.
문제 해결
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| Sensor not enrolling with panel. | Incorrect panel programming mode; sensor not activated; battery low/dead. | Ensure panel is in correct enrollment mode. Activate sensor multiple times. Replace battery. Check panel manual for specific steps. |
| Sensor not detecting open/close. | Magnet too far from sensor; incorrect mounting; dead battery. | Verify magnet is within 0.5 inches of the sensor. Re-mount if necessary. Replace battery. |
| External contact not working. | Incorrect wiring; faulty external device. | Check wiring connections to the WST-232. Test the external device independently. |
| Low battery warning on panel. | 배터리 수명이 거의 다 됐습니다. | Replace the CR2032 battery as soon as possible. |
명세서
- 모델: WST-232
- 호환성: Honeywell 5800 Wireless, 2GIG
- 치수: 3 x 1.7 x 1 인치(대략)
- 배터리: 1 x CR2032 Lithium Coin Cell
- 작동 주파수: 345MHz
- 제조업체: Ecolink Intelligent Technology Inc
- 한국어: 657479755391
보증 및 기술 지원
For warranty information and technical assistance, please refer to the official Ecolink web사이트를 방문하거나 고객 지원팀에 직접 문의하세요. 구매 증빙 자료로 구매 영수증을 보관하세요.
에코링크 Web대지: www.ecolink.com
