소개
This manual provides detailed instructions for the installation, operation, and maintenance of your DieseRC Kinetic Wireless Light Switch and 10A Relay Receiver Kit. Please read this manual thoroughly before installation and use to ensure safe and efficient operation.
The DieseRC Kinetic Wireless Light Switch system offers a convenient and energy-efficient solution for controlling lighting and other electrical appliances. It features a self-generating switch that requires no batteries and an RF 433 MHz relay receiver with a 10A fuse for protection.
안전 정보
- 수신기를 설치하거나 수리하기 전에 항상 회로 차단기에서 전원을 차단하십시오.
- 설치는 자격을 갖춘 전기 기술자나 충분한 전기 지식을 갖춘 사람이 수행해야 합니다.
- Ensure the receiver's load does not exceed 1500W (10A at 110V-240V AC).
- The wireless switch is IPX4 waterproof, suitable for damp environments, but avoid submerging it in water.
- 기기를 수리하거나 개조하지 마십시오. 도움이 필요하시면 고객 지원팀에 문의하십시오.
설정 및 설치
1. 패키지 내용
- 1 x DieseRC Kinetic Wireless Switch
- 1 x DieseRC 10A Relay Receiver
- 장착 액세서리(나사, 양면 테이프)
- 사용자 설명서
2. 구성요소 종료view
The wireless switch is self-powered and measures approximately 86mm x 86mm x 11mm. The compact relay receiver measures 60mm x 43mm x 27mm and includes a learning button, indicator light, and a replaceable 10A fuse.
3. 수신기 배선
The receiver must be wired between the power supply (AC 110V-240V) and the appliance you wish to control. Ensure power is disconnected before wiring.
- 전원 공급 장치에서 활선(L)과 중성선(N)을 확인하십시오.
- Connect the Live (L) wire from the power supply to the 'L INPUT' terminal on the receiver.
- Connect the Neutral (N) wire from the power supply to the 'N INPUT' terminal on the receiver.
- Connect the Live (L) wire of your appliance (e.g., light fixture) to the 'L OUTPUT' terminal on the receiver.
- Connect the Neutral (N) wire of your appliance to the 'N OUTPUT' terminal on the receiver.
- 모든 연결이 안전한지 확인하세요.
The receiver is designed to handle a maximum load of 1500W and operates on AC 110V-240V. It includes a 10A fuse for overload protection.
4. Switch Placement
The kinetic wireless switch requires no wiring or batteries, offering flexible placement options:
- 벽걸이 : Use the provided screws or double-sided tape to fix the switch to any wall surface.
- 유리 표면: The double-sided tape allows for mounting on glass.
- 휴대용 사용: The switch can be placed on a table or carried as a portable remote control.
작업
1. Pairing the Wireless Switch with the Receiver
To establish communication between the wireless switch and the receiver, follow these pairing steps:
- Press and hold the learning button on the receiver for approximately 3-5 seconds. The blue indicator light on the receiver will illuminate. Release the button.
- Within a few seconds, press one button on the kinetic wireless wall switch once.
- The indicator light on the receiver will flash, indicating successful pairing.
Once paired, pressing the switch will toggle the connected appliance ON or OFF.
2. Clearing the Paired Signal
To clear all paired signals from the receiver (e.g., when replacing a switch or reconfiguring):
- Press and hold the learning button on the receiver for approximately 8-10 seconds.
- The indicator light will flash multiple times, confirming that all stored signals have been cleared.
3. Multi-Control Scenarios
The system supports flexible control configurations:
- 스위치 여러 개, 수신기 하나: You can pair up to 5 wireless switches with a single receiver, allowing control from various locations (e.g., top and bottom of stairs).
- 스위치 하나로 여러 개의 수신기 연결: A single wireless switch can be paired with multiple receivers to control several appliances simultaneously or in different areas.
4. Control Distance and Signal Penetration
The system utilizes RF 433 MHz radio frequency for signal transmission. A strong signal can pass through walls, floors, and doors. The typical indoor control distance is up to 50 meters. In open outdoor spaces, the control distance can extend up to 100 meters.
유지
- 청소: Wipe the switch and receiver with a dry, soft cloth. Do not use abrasive cleaners or solvents.
- 퓨즈 교체: The receiver contains a replaceable 10A fuse. If the receiver stops functioning due to an overload, disconnect power, open the fuse compartment, and replace the fuse with one of the same rating (10A).
- Self-Powered Switch: The kinetic switch does not require battery replacement. Its self-generating mechanism is designed for long-term use (over 200,000 clicks).
- 릴레이 수명: The high-quality relay in the receiver is designed for over 400,000 operations.
문제 해결
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| 기기가 켜지거나 꺼지지 않습니다. |
|
|
| Reduced control distance or intermittent operation. |
|
|
| 스위치가 뻑뻑하거나 반응이 느립니다. |
|
|
명세서
| 특징 | 세부 사항 |
|---|---|
| 상표 | 디제RC |
| 모델 번호 | 2201NB+WP40 |
| 스위치 유형 | Kinetic Wireless Self-Generating Switch |
| 수신기 유형 | RF 433 MHz Relay Receiver |
| 운영 볼륨tage (수신기) | 교류 110V-240V |
| 최대 부하(수신기) | 10A/1500W |
| 퓨즈 | 10A(교체 가능) |
| 무선 주파수 | 433MHz |
| Indoor Control Distance | 최대 50미터 |
| Outdoor Control Distance | 최대 100미터(광활한 공간) |
| 스위치 수명 | 200,000만 클릭 이상 |
| 릴레이 수명 | > 400,000 작업 |
| Waterproof Rating (Switch) | IPX4 |
| 재료 | 플라스틱 |
| Switch Dimensions (L x W x H) | 86mm x 86mm x 11mm |
| 수신기 크기(길이 x 너비 x 높이) | 60mm x 43mm x 27mm |
| 작동 모드 | 온-오프 |
| 커넥터 유형 | 나사 단자 |
보증 정보
DieseRC products are manufactured to high-quality standards. Specific warranty details may vary by region and retailer. Please retain your proof of purchase for any warranty claims. For detailed warranty terms, refer to the documentation provided with your purchase or contact DieseRC customer support.
고객 지원
If you encounter any issues or have questions regarding your DieseRC Kinetic Wireless Light Switch and 10A Relay Receiver Kit, please contact DieseRC customer support through your retailer or the official DieseRC website. Our team is dedicated to providing assistance and resolving any concerns you may have.
