소개
Thank you for choosing the AZZA LCAZ-240C-ARGB Liquid Cooling System. This manual provides essential information for the proper installation, operation, and maintenance of your new CPU cooler. Please read this manual thoroughly before installation to ensure optimal performance and longevity of your system.
그림 1: The AZZA LCAZ-240C-ARGB Liquid Cooling System, featuring a 240mm radiator, two 12cm ARGB fans, and an ARGB pump/cold plate assembly. The fans and pump display vibrant, customizable lighting.
패키지 내용
Verify that all components are present before beginning installation. If any items are missing or damaged, please contact AZZA support.
- AZZA LCAZ-240C-ARGB Radiator with Pump/Cold Plate Assembly
- Two 120mm ARGB Fans
- 장착 하드웨어 키트(인텔 및 AMD 소켓용)
- Fan and ARGB Splitter Cables
- 써멀 페이스트(미리 도포된 형태 또는 튜브형)
- 사용 설명서 (본 문서)
명세서
| 특징 | 세부 사항 |
|---|---|
| 모델 번호 | LCAZ-240C-ARGB |
| 냉각 방식 | 액체형 (올인원) |
| 팬 직경 | 12cm |
| 최대 기류 | 54 퀴놀론 |
| 최대 기압 | 1.44mm수소 |
| 소음 수준 | 48데시벨 |
| 전원 커넥터 유형 | 3핀(펌프), 4핀 PWM(팬) |
| Radiator Dimensions (W x D x H) | 274mm x 52mm x 120mm |
| 제품 색상 | 검은색 |
| 호환 장치 | 데스크톱 (다양한 인텔/AMD 소켓) |
설정 및 설치
Before proceeding, ensure your computer is powered off and unplugged from the wall outlet. Refer to your motherboard and PC case manuals for specific mounting locations and clearances.
- 마더보드 준비: Install the appropriate backplate and standoffs for your CPU socket (Intel or AMD) onto the motherboard.
- 열 페이스트 적용: If thermal paste is not pre-applied to the cold plate, apply a small, pea-sized amount to the center of your CPU's integrated heat spreader (IHS).
- Mount Cold Plate: Carefully place the pump/cold plate assembly onto the CPU, aligning the mounting holes. Secure it with the provided thumb screws or nuts, tightening them in a diagonal pattern until snug. Do not overtighten.
- 라디에이터와 팬 설치: Attach the two 120mm fans to the radiator using the long screws. Ensure the fan airflow direction is appropriate for your case (intake or exhaust). Mount the radiator assembly to an available fan mount in your PC case (e.g., top, front, or rear).
- 케이블 연결:
- 펌프의 3핀 전원 케이블을 마더보드의 AIO_PUMP 또는 CPU_FAN 헤더에 연결하십시오.
- Connect the two fan 4-pin PWM cables to the included fan splitter cable, then connect the splitter to a CPU_FAN or SYS_FAN header on your motherboard.
- Connect the ARGB cables from the fans and pump to the included ARGB splitter cable, then connect the splitter to a 5V 3-pin ARGB header on your motherboard. 12V RGB 헤더에 연결하지 마십시오.
- 케이블 관리 : Route all cables neatly to avoid interference with other components and to improve airflow.
작동 지침
Once installed, the AZZA LCAZ-240C-ARGB operates automatically.
- 전원 켜기: After completing installation and securing all connections, power on your computer.
- BIOS/UEFI 설정: Access your motherboard's BIOS/UEFI to ensure the CPU_FAN or AIO_PUMP header is set to PWM mode (if applicable) and that fan curves are configured for optimal cooling and noise levels.
- ARGB 제어: Use your motherboard's ARGB software (e.g., ASUS Aura Sync, MSI Mystic Light Sync, Gigabyte RGB Fusion, ASRock Polychrome Sync) to customize the lighting effects of the fans and pump.
- 모니터 온도: Use monitoring software to observe CPU temperatures, especially during initial use and under load, to confirm proper cooling performance.
유지
Regular maintenance helps ensure the longevity and efficiency of your liquid cooling system.
- 먼지 제거: Periodically clean dust from the radiator fins and fan blades using compressed air or a soft brush. Dust accumulation can impede airflow and reduce cooling performance.
- 튜빙 검사: 튜브에 꼬임, 누출 또는 손상 흔적이 있는지 주기적으로 확인하십시오.
- 팬 작동 : Ensure both fans are spinning freely and quietly. Replace any fans that become excessively noisy or stop functioning.
- 펌프 작동: Listen for any unusual noises from the pump. A constant, low hum is normal, but grinding or rattling sounds may indicate an issue.
문제 해결
If you encounter issues with your AZZA LCAZ-240C-ARGB, refer to the following common problems and solutions.
- 높은 CPU 온도:
- Ensure the pump is running and connected to a constant power source (AIO_PUMP header).
- Verify that the cold plate is making proper contact with the CPU and that thermal paste was applied correctly.
- Check that fans are spinning and oriented correctly for optimal airflow through the radiator.
- 라디에이터 핀에 쌓인 먼지를 깨끗이 닦아내십시오.
- 팬이 회전하지 않거나 ARGB 조명이 켜지지 않음:
- Confirm all fan and ARGB cables are securely connected to the motherboard headers and splitters.
- Ensure the ARGB cable is connected to a 5V 3-pin ARGB header, not a 12V 4-pin RGB header.
- Check your motherboard's BIOS/UEFI settings for fan control and ARGB settings.
- 메인보드의 ARGB 소프트웨어가 올바르게 설치 및 구성되었는지 확인하십시오.
- 비정상적인 펌프 소음:
- 펌프에 충분한 전력이 공급되고 있는지 확인하십시오.
- Check for air bubbles in the loop by gently tilting your PC case.
- If the noise persists and is disruptive, contact AZZA support.
보증 및 지원
AZZA products are designed for reliability and performance. This product comes with a limited warranty against defects in materials and workmanship. For specific warranty terms and conditions, please refer to the warranty card included with your product or visit the official AZZA web대지.
For technical support, troubleshooting assistance, or to inquire about replacement parts, please contact AZZA customer service through their official web대지: www.azza.com.
