1. 서론
This manual provides detailed instructions for the installation, operation, and maintenance of the Dynatron J12 3U Active Heatsink. This heatsink is designed for AMD Genoa Processor Family, specifically for Socket SP5, and is suitable for 3U server environments and up. It features aluminum stacked fins, heat pipes, and a copper heat spreader embedded in an aluminum heatsink base, capable of supporting up to 320 Watts CPU power heat dissipation.
2. 안전 정보
- 구성품을 설치하거나 제거하기 전에 항상 시스템의 전원을 차단하십시오.
- Handle the heatsink and CPU with care to avoid damage to pins or surfaces.
- Wear anti-static gloves or use an anti-static wrist strap when handling internal computer components.
- Ensure proper ventilation in the server chassis to prevent overheating.
- 어린이의 손이 닿지 않는 곳에 보관하세요.
3. 패키지 내용
패키지에 다음 품목이 포함되어 있는지 확인하세요.
- Dynatron J12 3U Active Heatsink with integrated fan.
- Mounting hardware (pre-attached or separate, depending on specific packaging).
- Thermal interface material (TIM) (pre-applied or in a separate tube).
품목이 누락되었거나 손상된 경우 판매자에게 문의하세요.
4. 설정 및 설치
Follow these steps to properly install the Dynatron J12 heatsink onto your AMD SP5 processor.
- 마더보드 준비: Ensure the motherboard is securely mounted in the server chassis. Locate the CPU socket (AMD SP5).
- CPU를 준비하세요: If not already installed, carefully place the AMD Genoa processor into the SP5 socket according to the motherboard manufacturer's instructions. Secure the CPU retention mechanism.
- 열 페이스트 적용: If thermal paste is not pre-applied to the heatsink base, apply a small, pea-sized amount of high-quality thermal paste to the center of the CPU's integrated heat spreader (IHS). Do not spread it manually; the pressure from the heatsink will distribute it evenly.
- 방열판을 배치하십시오: Carefully align the Dynatron J12 heatsink with the mounting holes around the CPU socket. Ensure the heatsink base makes full contact with the CPU's IHS.
- 방열판을 고정하십시오: Gently press down on the heatsink and secure it using the provided mounting screws or clips. Tighten screws in a diagonal pattern (e.g., top-left, bottom-right, top-right, bottom-left) to ensure even pressure. Do not overtighten.
- 팬 연결: Locate the CPU fan header on your motherboard. Connect the 4-pin fan connector from the Dynatron J12 heatsink to this header. Ensure the connector is fully seated.
그림 1: 기본 view of the Dynatron J12 heatsink, showing the fan, aluminum fins, and heat pipes.
그림 2: 앞쪽 view of the Dynatron J12 heatsink, highlighting the fan and its connection cable.
그림 3: 옆 view of the Dynatron J12 heatsink, illustrating the heat pipes extending through the aluminum fins.
그림 4: 맨 아래 view of the Dynatron J12 heatsink, showing the copper heat spreader contact plate.
5. 사용 설명서
Once installed, the Dynatron J12 heatsink operates automatically to cool your CPU. The integrated fan's speed is typically controlled by the motherboard's BIOS/UEFI settings based on CPU temperature.
- 초기 전원 켜기: After installation, power on your system. Observe the fan to ensure it spins freely.
- BIOS/UEFI 설정: Access your motherboard's BIOS/UEFI to verify that the CPU fan is detected and operating correctly. You may adjust fan speed curves if your motherboard supports it, though default settings are usually sufficient.
- 온도 모니터링: Use system monitoring software to keep an eye on CPU temperatures, especially during initial operation and under load, to ensure effective cooling.
6. 유지관리
정기적인 유지보수는 히트싱크의 최적 성능과 수명 연장에 도움이 됩니다.
- 먼지 제거: Periodically (e.g., every 3-6 months, depending on environment) inspect the heatsink fins and fan blades for dust accumulation. Use compressed air to gently blow dust away from the fins and fan. Hold the fan blades stationary while using compressed air to prevent over-spinning and potential damage to the bearing.
- 팬 검사: Check the fan for any signs of wear, unusual noise, or reduced rotational speed. Ensure the fan cable remains securely connected.
- 열전도 페이스트: The thermal paste typically lasts for several years. If you notice consistently high CPU temperatures, consider reapplying thermal paste. This involves carefully removing the heatsink, cleaning off old thermal paste from both the CPU and heatsink base, and applying new thermal paste.
7. 문제 해결
If you encounter issues with your Dynatron J12 heatsink, refer to the following common problems and solutions:
- 팬이 회전하지 않음:
- Check if the fan cable is securely connected to the CPU fan header on the motherboard.
- Verify fan settings in the motherboard's BIOS/UEFI. Ensure fan control is enabled.
- Inspect for any physical obstructions preventing the fan blades from rotating.
- 높은 CPU 온도:
- Ensure the heatsink is properly seated and making full contact with the CPU. Re-tighten mounting screws if necessary.
- Check for excessive dust buildup on the heatsink fins and fan. Clean as described in the Maintenance section.
- Verify that thermal paste was applied correctly and is not dried out. Reapply if needed.
- Ensure adequate airflow within the server chassis.
- 평소와 다른 선풍기 소음:
- 느슨한 케이블이나 기타 부품이 팬 날개에 닿아 있는지 확인하십시오.
- Dust accumulation can cause imbalance; clean the fan.
- If the noise persists and is a grinding or rattling sound, the fan bearing may be failing. Consider replacing the fan.
8. 사양
| 특징 | 사양 |
|---|---|
| CPU 지원 | AMD Genoa Processor Family |
| CPU 소켓 | 소켓 SP5 |
| 해결책 | 3U 서버 이상 |
| 치수(높이 x 너비 x 깊이) | 118.0 x 92.4 x 105.0mm(4.6인치 길이 x 3.6인치 너비 x 4.1인치 높이) |
| 재료 | Aluminum Fin + Heat pipes + Copper Heat Spreader Embedded Aluminum Heatsink Base |
| Max CPU Power Dissipation | 최대 320와트 |
| 팬 베어링 유형 | 더블 볼 |
| 정격 볼륨tage | 12V |
| Fan Speed (20% Duty Cycle) | 2400 ± 200RPM |
| Fan Speed (50% Duty Cycle) | 4800±10%RPM |
| Fan Speed (100% Duty Cycle) | 8000±10%RPM |
| Air Flow (20% Duty Cycle) | 32.52 퀴놀론 |
| Air Flow (50% Duty Cycle) | 67.24 퀴놀론 |
| Air Flow (100% Duty Cycle) | 115.61 퀴놀론 |
| Noise Level (20% Duty Cycle) | 25.63데시벨 |
| Noise Level (50% Duty Cycle) | 47.85데시벨 |
| Noise Level (100% Duty Cycle) | 64.40데시벨 |
| Air Pressure (20% Duty Cycle) | 1.39mm수소 |
| Air Pressure (50% Duty Cycle) | 5.97mm수소 |
| Air Pressure (100% Duty Cycle) | 34.06mm수소 |
| 품목 무게 | 798그램(1.76파운드) |
9. 보증 및 지원
Dynatron products are manufactured to high-quality standards. For specific warranty terms and conditions, please refer to the warranty information provided with your purchase or visit the official Dynatron website. In case of technical issues or questions not covered in this manual, please contact your retailer or Dynatron customer support for assistance.
