1. 서론
The AeroCool Blade is an ATX semi-tower PC case designed for optimal airflow and aesthetic appeal. It features an RGB front panel with preset lighting modes, a full tempered glass side window, and ample space for component installation. This manual provides essential information for the proper setup, operation, and maintenance of your PC case.
안전 정보: Always disconnect power from your system before performing any installation or maintenance. Handle components with care to avoid damage. Refer to individual component manuals for specific installation instructions.
2. 패키지 내용
- AeroCool Blade ATX Semi-Tower PC Case
- 1 x 120mm RGB Rear Fan (pre-installed)
- 3 x 120mm Front Fans (pre-installed)
- 액세서리 키트(나사, 스탠드오프, 케이블 타이)
3. 설정 및 설치
3.1 사건 준비
Carefully remove the case from its packaging. Place it on a stable, flat surface. Remove the tempered glass side panel by unscrewing the thumb screws at the rear of the case and gently pulling the panel away.
그림 3.1: 내부 view of the AeroCool Blade PC case, illustrating the layout for component installation.
3.2 마더 보드 설치
- Install the necessary motherboard standoffs into the motherboard tray according to your motherboard's form factor (ATX, Micro-ATX, Mini-ITX).
- 케이스 후면 개구부에 I/O 실드를 설치합니다.
- 나사 구멍을 맞춰서 마더보드를 스탠드오프에 조심스럽게 올려놓습니다.
- 제공된 나사로 마더보드를 고정합니다.
3.3 전원 공급 장치(PSU) 설치
The AeroCool Blade supports bottom-mounted PSUs. Slide your PSU into the dedicated compartment at the bottom rear of the case. Secure it with screws from the rear of the case.
3.4 저장 드라이브 설치
- 3.5인치 HDD: Install 3.5" hard drives into the drive cage located beneath the PSU shroud.
- 2.5" SSDs/HDDs: Install 2.5" drives onto the dedicated mounting points on the motherboard tray or behind it.
그림 3.2: 후면 내부 view, highlighting cable management routes and 2.5-inch drive mounting locations.
3.5 확장 카드(GPU) 설치
Remove the necessary expansion slot covers from the rear of the case. Insert your graphics card or other expansion cards into the PCIe slots on your motherboard and secure them with screws.
3.6 팬 및 냉각 장치 설치
The case comes with one 120mm RGB fan pre-installed at the rear and three 120mm fans pre-installed at the front. Ensure all fan cables are connected to appropriate headers on your motherboard or fan controller.
Figure 3.3: A 120mm RGB fan, similar to those pre-installed in the AeroCool Blade case.
3.7 전면 패널 I/O 연결
Connect the front panel cables (USB 3.0, USB 2.0, HD Audio, Power Switch, Reset Switch, LED Switch, Power LED, HDD LED) to the corresponding headers on your motherboard. Refer to your motherboard manual for exact pin configurations.
4. 사용 설명서
4.1 전원 켜기
Once all components are installed and connected, replace the side panel. Connect your monitor, keyboard, mouse, and power cable to the PSU. Press the Power button located on the top panel of the case to turn on your system.
그림 4.1: 상단 전면 view of the case, indicating the location of the power button and front I/O ports.
4.2 RGB 조명 제어
The AeroCool Blade features an RGB front panel. Use the dedicated LED button on the top panel to cycle through various preset lighting modes and effects. Pressing the button will change the lighting pattern or color.
그림 4.2: 전면 view of the AeroCool Blade case with its distinctive RGB lighting.
4.3 전면 패널 포트
상단 패널을 통해 다음과 같은 기능에 편리하게 접근할 수 있습니다.
- 1 x USB 3.0 포트
- 2개의 USB 2.0 포트
- HD Audio output
- 마이크 입력
Connect your USB devices, headphones, and microphone to these ports as needed.
5. 유지관리
5.1 먼지 필터 청소
Regularly check and clean the dust filters to maintain optimal airflow and prevent dust buildup inside the case. Dust filters are typically located at the top, front, and bottom (under the PSU). Gently remove them and clean with compressed air or rinse with water (ensure they are completely dry before re-installation).
5.2. 외부 청소
케이스 외부 표면을 부드러운 천으로 닦으십시오.amp 천을 사용하십시오. 마감재나 강화유리를 손상시킬 수 있는 강한 화학 물질이나 연마재는 사용하지 마십시오.
6. 문제 해결
- 시스템 전원이 켜지지 않습니다:
Ensure the PSU is switched on and properly connected to the wall outlet. Verify all power cables from the PSU are correctly connected to the motherboard and components. Check the front panel power switch connection to the motherboard. - RGB 조명이 작동하지 않음:
Ensure the RGB controller (if applicable) and fan RGB cables are securely connected. Press the LED button on the top panel to cycle through modes. If connected to a motherboard header, check motherboard software settings. - 팬이 회전하지 않음:
Verify that all fan power cables are securely connected to the motherboard fan headers or a fan controller. Check BIOS/UEFI settings for fan speed control. - 전면 패널 USB/오디오가 작동하지 않습니다.
Ensure the USB and HD Audio cables from the front panel are correctly connected to the corresponding headers on your motherboard.
7. 사양
Figure 7.1: Dimensions of the AeroCool Blade PC Case.
| 특징 | 사양 |
|---|---|
| 상표 | 에어로쿨 |
| 모델명 | BLADEBK |
| 케이스 유형 | Semi-Tower |
| 마더보드 호환성 | ATX, 마이크로 ATX, 미니 ITX |
| 재료 | 강화유리(측면 패널) |
| 제품 크기(L x W x H) | 43.1 x 20.3 x 35.7cm |
| 품목 무게 | 4kg |
| 드라이브 베이 | 2 x 3.5", 2 x 2.5" |
| GPU 여유 공간 | 최대 307mm |
| CPU 쿨러 높이 | 최대 155mm |
| 전면 I / O 포트 | 1 x USB 3.0, 2 x USB 2.0, HD Audio, Mic, LED Control, Power |
| 사전 설치된 팬 | 1 x 120mm RGB Rear, 3 x 120mm Front |
| 냉각 방식 | 공기 |
8. 보증 및 지원
보증 정보 및 기술 지원에 대해서는 AeroCool 공식 웹사이트를 참조하십시오. web사이트를 방문하거나 가까운 판매점에 문의하세요. 보증 청구를 위해 구매 증빙 자료를 보관하세요.
연락처 정보: 추가 지원을 받으려면 다음을 방문하십시오. www.aerocool.io.
