TOTAL 리튬 이온 공기 압축기 TACLI2003 사용 설명서

1. 서론

This manual provides essential information for the safe and efficient operation, setup, and maintenance of your TOTAL Lithium-ion Air Compressor, model TACLI2003. Please read this manual thoroughly before using the compressor and retain it for future reference.

2. 안전 지침

Always observe basic safety precautions to reduce the risk of fire, electric shock, and personal injury when operating this product.

• 모든 지침 읽기: 압축기의 제어 방법과 올바른 사용법을 익혀보세요.
• 작업 영역: 작업 공간을 깨끗하고 밝게 유지하십시오. 어수선하거나 어두운 곳은 사고를 유발합니다.
• 전기 안전: This unit operates on 40V (2x20V) lithium-ion batteries. Ensure batteries and charger (not included) are compatible with TOTAL 20V tools. Do not expose the compressor to rain or wet conditions.
• 개인 안전: Always wear eye protection. Use hearing protection when operating the compressor for extended periods. Do not overreach; maintain proper footing and balance at all times.
• Compressor Use and Care: Do not operate the compressor if the power switch does not turn it on and off. Disconnect the battery pack before making any adjustments, changing accessories, or storing the compressor. Store idle compressors out of the reach of children and do not allow persons unfamiliar with the compressor or these instructions to operate it.
• 압력 안전: Never exceed the maximum pressure rating of any accessory or item being inflated. The maximum pressure for this compressor is 9.3 bar (135 psi).
• 유지: Have your compressor serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

3. 패키지 내용

Upon unpacking, ensure all items listed below are present and undamaged. If any parts are missing or broken, please contact your retailer.

• TOTAL Lithium-ion Air Compressor (TACLI2003)
• 1 pc Steel Ball / Air Needle
• 1 pc Plastic Ball Needle
• 1 pc Schrader Presta Valve Adaptor

메모: Batteries and charger are not included with this unit and must be purchased separately.

4. 제품 오버view

그림 1: 앞-왼쪽 view of the TOTAL Lithium-ion Air Compressor TACLI2003, showcasing the main unit, 6L tank, and control panel with gauges.

그림 2: Close-up of the compressor's control panel, featuring two pressure gauges (tank and output), a power switch, and a pressure regulator knob.

그림 3: 상세한 view of the pressure gauges and the adjustable pressure regulator knob, allowing precise control over air output.

그림 4: Another close-up of the pressure regulator knob, which is used to set the desired output air pressure.

그림 5: 옆 view showing the two battery compartments designed for 20V TOTAL lithium-ion batteries (not included).

그림 6: 뒤쪽 view of the compressor, highlighting the integrated storage compartment for various nozzles and adaptors.

그림 7: Close-up of the accessory storage, showing the included steel ball/air needle, plastic ball needle, and Schrader Presta valve adaptor.

그림 8: Detail of the pressure relief valve, an important safety feature designed to release excess pressure from the tank.

5. 설정

5.1 배터리 설치

1. Ensure the compressor's power switch is in the 'OFF' position.
2. Locate the two battery compartments on the side of the compressor (refer to Figure 5).
3. Insert two fully charged TOTAL 20V lithium-ion batteries (2.0Ah or 4.0Ah compatible) into the compartments until they click securely into place.
4. To remove batteries, press the release tabs on each battery and pull them out.

5.2 액세서리 연결

1. Identify the quick-connect air outlet on the compressor.
2. Select the appropriate accessory (e.g., air needle, valve adaptor) for your task.
3. Attach the accessory to an air hose (not included) and then connect the air hose to the compressor's air outlet. Ensure a secure connection to prevent air leaks.

6. 사용 설명서

6.1 Powering On and Initial Pressure Build-up

1. With batteries installed and accessories connected, ensure the pressure regulator knob (Figure 3) is turned fully counter-clockwise to the lowest setting.
2. Flip the power switch to the 'ON' position. The compressor will begin to fill the 6L air tank.
3. Monitor the tank pressure gauge. The compressor will automatically shut off once the maximum tank pressure (9.3 bar / 135 psi) is reached.

6.2 출력 압력 조정

1. Once the tank is full, slowly turn the pressure regulator knob clockwise to increase the output pressure.
2. Observe the output pressure gauge to set the desired working pressure for your tool or inflation task.
3. Never exceed the recommended pressure for the item being inflated or the connected air tool.

6.3 작동

1. Engage your air tool or begin inflation. The compressor will cycle on and off automatically to maintain the set output pressure as air is consumed.
2. When finished, turn the power switch to 'OFF'.
3. Release any remaining pressure from the air hose and tool before disconnecting.

7. 유지관리

정기적인 유지보수는 최적의 성능을 보장하고 공기 압축기의 수명을 연장시켜 줍니다.

• 일일:
• Inspect the compressor for any visible damage, loose connections, or air leaks.
• Check the air filter (if accessible) for excessive dirt and clean if necessary.
• Weekly/After Each Use:
• 압축기 외부를 깨끗한 천으로 닦아주세요.amp 천. 독한 화학 물질을 사용하지 마십시오.
• Ensure the pressure relief valve (Figure 8) operates freely by pulling its ring briefly to release a small amount of air.
• 배터리 관리 :
• Always store batteries in a cool, dry place away from direct sunlight.
• Charge batteries fully before storage and periodically during long storage periods to maintain battery health.

8. 문제 해결

9. 사양

10. 보증 및 지원

For warranty information, technical support, or service inquiries, please refer to the warranty card included with your purchase or contact your authorized TOTAL tools dealer. Keep your purchase receipt as proof of purchase for any warranty claims.