BESTTEN 디머 라이트 스위치 및 조합 토글 스위치 & 듀플렉스 리셉터클 콘센트 사용 설명서

1. 제품 오버view

This manual provides instructions for the BESTTEN 2-Pack Dimmer Light Switch and 2-Pack Combination Toggle Light Switch & Duplex Receptacle Outlet. These devices are designed for residential electrical installations, offering both lighting control and power outlets in a single unit or as dedicated dimmer switches.

이미지 1.1: 위에view of the BESTTEN Dimmer Light Switches and Combination Toggle Light Switches with Duplex Receptacle Outlets. The image displays two dimmer switches and two combination switches, all in white, with their respective wall plates.

2. 안전 정보

WARNING: Risk of Electric Shock. May result in serious injury or death. Turn off power at the circuit breaker or fuse and test that power is off before wiring!

• Always turn off power at the circuit breaker or fuse before installation, servicing, or removing any fixture.
• 설치는 자격을 갖춘 전기 기술자가 수행하거나 해당 지역의 전기 규정에 따라 수행해야 합니다.
• Use only with copper or copper-clad wire. Do not use with aluminum wire.
• 모든 전선 연결이 안전하고 적절하게 절연되어 있는지 확인하세요.
• Do not exceed the specified electrical ratings for the device (15A/120V for toggle switch, 15A/125V for duplex receptacle).
• 이 장치는 실내에서만 사용하도록 설계되었습니다.

3. 제품 특징

Dimmer Light Switch:

• Supports single-pole or 3-way applications. Note: Only one dimmer switch can be installed per 3-way circuit.
• Provides optimal dimming performance for LED bulbs, also compatible with CFL and incandescent bulbs.
• Features a horizontal slider for full-range light control.
• Includes an adjustable dimming range to eliminate flickering issues with various bulb types.
• 안전과 품질 보증을 위해 UL 인증을 받았습니다.
• Wall plate included.

이미지 3.1: Features of the BESTTEN Dimmer Switch. Highlights include "No Neutral Required," "Full-Range Dimming with Slide Controller," "Wide Compatibility with Side Adjuster," "Rocker Switch," "Wall Plate Included," "UL/cUL Listed," and "Single-Pole or 3-Way" application.

Combination Toggle Light Switch & Duplex Receptacle Outlet:

• Toggle light switch: Single pole, 15A/120V.
• Duplex receptacle outlet: 15A/125V/1875W.
• Supports common feed and separate feed (two circuits) applications.
• Side wire only, accepts up to 12AWG copper or copper-clad wire.
• Heat and impact-resistant body.
• 안전과 품질 보증을 위해 UL 인증을 받았습니다.
• Wall plate included.

이미지 3.2: 상세한 view of the BESTTEN Combination Toggle Light Switch and Duplex Receptacle Outlet. Specifications for the toggle light switch (Single Pole, 15A, 120/277V) and duplex outlet (15A/125V/1875W) are shown, along with features like "Supports 2-Circuit Application," "Heat and Impact-Resistant Body," "UL Listed," and "Wall Plate Included."

4. 설치 지침

4.1 일반 배선 지침

1. 전원 끄기: Before starting, ensure power is OFF at the circuit breaker or fuse box. Verify with a voltag전자 테스터.
2. 전선 식별: Carefully identify the Line (hot), Load, Neutral (if applicable), and Ground wires in your electrical box.
3. 전선 연결: Connect the wires to the device terminals as instructed below. Use side wiring only, accepting up to 12AWG copper or copper-clad wire.
4. 보안 장치: Mount the device into the electrical box and attach the wall plate.
5. 복원력 : 회로 차단기에서 전원을 다시 켜십시오.

4.2 Dimmer Switch Wiring (3-Way Application Examp르)

For 3-way applications, only one dimmer switch can be installed per circuit. The other switch in the 3-way circuit should be a standard 3-way switch.

이미지 4.1: 3-Way Wiring Instruction for the BESTTEN Dimmer Switch. This diagram illustrates connecting the Hot Black Wire (120V 60Hz) to one terminal, two Traveler Red Wires to the other two terminals, and the Ground Green Wire to the ground screw. The Hot/Load Black Wire from the light fixture connects to the remaining terminal.

How to change from a standard 3-Way switch:

When removing your old switch, take a picture of the wire locations for future reference. Note that two terminals on the old switch will have the same color wires (travelers). These wires connect to the two red wires on your new dimmer. Mark the wire that was connected to the third terminal on your old switch; this will be your line or load wire and will connect to the black wire on your new dimmer. The ground wire (green or bare copper) from your old switch connects to the green wire on your new dimmer.

4.3 Combination Switch & Outlet Wiring

This device supports both common feed and separate feed (two circuits) applications.

이미지 4.2: Illustration of the Two Circuits Application for the BESTTEN Combination Switch and Outlet. It highlights that the break-off pin located between the black screws should be removed before wiring for separate circuits.

• 공통 피드: For a single circuit powering both the switch and the outlet, connect the incoming hot wire to one of the black screws. Connect the load wire for the light to the other black screw. Connect the neutral wire to the silver screw and the ground wire to the green screw.
• Separate Feed (Two Circuits): If you intend to power the switch and the outlet from two different circuits, the break-off pin located between the black screws must be removed before wiring. This isolates the switch and outlet, allowing them to be wired to separate hot feeds. Connect the hot wire for the switch to one black screw and its load wire to the other black screw. Connect the hot wire for the outlet to one of the remaining black screws and its neutral to the silver screw. Connect ground wires to the green screw.

5. 사용 설명서

5.1 Dimmer Light Switch Operation

• 켜기/끄기: Press the rocker switch to turn the connected light fixture ON or OFF.
• 디밍 : Use the horizontal slider located below the rocker switch to adjust the light intensity. Slide up to brighten, slide down to dim.

5.2 Combination Toggle Switch & Duplex Receptacle Operation

• 토글 스위치: Flip the toggle switch up or down to control the connected light fixture.
• Duplex Receptacle: Insert plugs into the two available outlets to power devices.

6. Dimming Range Adjustment (for Dimmer Switch)

The dimming range of LED bulbs can vary. If you experience flickering, hum, or buzz, or if the bulbs do not dim to your satisfaction, adjust the dimmer's range using the side adjustment wheel.

1. Move the horizontal slider to the leftmost (lowest dimming) position.
2. Turn on the light by pressing the rocker switch.
3. Locate the small adjustment wheel on the side of the dimmer switch. Rotate this wheel to set the optimal dimming range and eliminate any flickering.

이미지 6.1: Steps for Dimming Range Setting on the BESTTEN Dimmer Switch to eliminate flickering. The steps are: 1. Move the slider to the leftmost position, 2. Turn on the light, 3. Adjust the wheel to set the dimming range or eliminate flickering.

이미지 6.2: Important note regarding dimmer compatibility. It states that dimmable LEDs may not dim the same as incandescent or halogen bulbs, and the dimming range can vary. The dimmer has an adjustable range, and if bulbs do not dim or exhibit issues, they may not be compatible, advising to refer to the user manual for adjustment.

7. 유지관리

These devices require minimal maintenance. Follow these guidelines:

• 청소: Disconnect power before cleaning. Wipe the surface with a soft, damp 천. 연마성 세척제나 용매를 사용하지 마십시오.
• 점검: Periodically inspect the devices and wall plates for any signs of damage, loose connections, or discoloration. If any issues are found, turn off power and consult a qualified electrician.

8. 문제 해결

• 표시등이 켜지지 않습니다:
  • 회로 차단기가 트립되었는지 확인하십시오.
  • 모든 전선 연결이 안전한지 확인하십시오.
  • Verify the bulb is working and properly installed.
• Light flickers or hums (Dimmer Switch):
  • Adjust the dimming range using the side adjustment wheel (refer to Section 6).
  • Ensure the bulb is dimmable and compatible with the dimmer.
  • 총 와트tage of connected bulbs may exceed the dimmer's capacity.
• Outlet is not working:
  • 회로 차단기가 트립되었는지 확인하십시오.
  • Ensure all wire connections are secure, especially the hot and neutral wires.
  • If using a separate feed, ensure the break-off pin was removed correctly and both circuits are powered.

9. 사양

이미지 9.1: Production dimensions for the BESTTEN Dimmer Switch. The image shows the front plate dimensions (4.48" H x 2.75" W) and the body dimensions (4.13" H x 2.12" W x 1.33" D), along with a basic wiring diagram indicating Line, Load, and Ground wires for a 3-way circuit.

10. 보증 및 지원

This BESTTEN product comes with a 3년 한정 보증 구매일로부터. 이 보증은 정상적인 사용 하에서 재료 및 제조상의 결함을 포함합니다.

For technical support, troubleshooting assistance, or warranty claims, please contact BESTTEN customer service. Refer to the product packaging or the official BESTTEN web최신 연락처 정보는 사이트에서 확인하세요.