EPOMAKER Mini Cat 64 60% Wired Keyboard Kit Instruction Manual

1. 설정

1.1 언박싱 및 구성품

Your EPOMAKER Mini Cat 64 kit includes the following components:

• Mini Cat 64 Kit (including PCB, Mounting Plate, Stabilizers)
• C타입 케이블

1.2 조립 지침

The Mini Cat 64 is a DIY keyboard kit. Follow these steps to assemble your keyboard:

1. 스위치 준비: Ensure your chosen 3-pin or 5-pin mechanical switches are ready for installation. The hot-swappable sockets allow for easy installation without soldering.
2. 스위치 설치: Align the pins of each switch with the corresponding holes on the PCB (Printed Circuit Board). Gently press down until the switch clicks into place. Ensure all switches are seated correctly.

Image: Installation of a 3-pin hot-swappable switch into the keyboard PCB.

3. 키캡 설치: Once all switches are installed, firmly press your desired keycaps onto the stems of the switches.
4. 케이스 조립: The kit features a stacked acrylic case. Carefully align and secure the acrylic layers around the PCB and mounting plate using the provided screws.

Image: Fully assembled EPOMAKER Mini Cat 64 keyboard kit showcasing the stacked acrylic case and RGB backlighting.

1.3 키보드 연결

Connect the keyboard to your computer using the provided Type-C cable. The keyboard is compatible with both Windows and Mac operating systems.

2. 사용 설명서

2.1 기본 키보드 기능

The Mini Cat 64 features a 60% layout, retaining essential keys while offering a compact form factor. All standard typing functions operate as expected.

2.2 RGB 백라이트

The keyboard is equipped with vibrant RGB backlighting. The stacked acrylic case enhances the lighting effects, allowing light to shine through the sockets and from the sides of the keyboard. Specific key combinations (refer to the included quick start guide) can be used to cycle through various lighting modes, colors, and brightness levels.

2.3 VIA 프로그래밍 가능성

The Mini Cat 64 kit is fully programmable via VIA software. This allows you to remap keys, create macros, and customize lighting effects without reflashing the firmware. Changes are saved directly on the keyboard's onboard memory.

1. 다운로드 방법: VIA 공식 웹사이트에서 최신 VIA 소프트웨어를 다운로드하세요. web대지.
2. 키보드 연결: Ensure your Mini Cat 64 is connected to your computer via the Type-C cable.
3. 레이아웃 로드: Open VIA and load the appropriate keymap for the Mini Cat 64.
4. 사용자 정의: Use the intuitive interface to remap keys, set up layers, and configure lighting to your preference.

Image: VIA software interface for customizing key assignments and layers.

3. 유지관리

3.1 키보드 청소

최적의 성능과 외관을 유지하려면 키보드를 정기적으로 청소하세요.

• 먼지 제거: Use a soft brush or compressed air to remove dust and debris from between keycaps.
• 표면 청소: Wipe the keycaps and case with a slightly damp보풀 없는 천을 사용하세요. 강한 화학 약품은 피하세요.

3.2 스위치 및 키캡 교체

Thanks to the hot-swappable design, switches and keycaps can be easily replaced:

• 키캡 제거: 키캡 풀러를 사용하여 키캡을 조심스럽게 제거하세요. 스위치 스템이 손상되지 않도록 위쪽으로 똑바로 당겨 빼내십시오.
• 스위치 제거 : Use a switch puller to carefully extract switches from the PCB. Squeeze the clips on the top and bottom of the switch and pull upwards.
• 설치: Follow the assembly steps (Section 1.2) to install new switches and keycaps.

4. 문제 해결

If you encounter issues with your Mini Cat 64 keyboard, please refer to the following common solutions:

• 키보드가 응답하지 않음:
  • Type-C 케이블이 키보드와 컴퓨터에 모두 단단히 연결되어 있는지 확인하세요.
  • 키보드를 컴퓨터의 다른 USB 포트에 연결해보세요.
  • 시스템 특정 문제를 배제하기 위해 다른 컴퓨터에서 키보드를 테스트하세요.
• 키가 등록되지 않음:
  • Carefully remove the keycap and switch for the affected key. Reinstall the switch, ensuring its pins are straight and fully seated in the hot-swappable socket.
  • 문제가 지속되면 정상 작동하는 스위치로 교체해 보십시오.
• RGB Backlighting Issues:
  • Check the keyboard's lighting controls (refer to the quick start guide) to ensure RGB is enabled and brightness is adjusted.
  • If using VIA, verify that your lighting profiles are correctly configured and applied.
• VIA 소프트웨어에서 키보드를 인식하지 못함:
  • Ensure VIA software is up-to-date.
  • Confirm the keyboard is connected via Type-C cable.
  • Restart your computer and the VIA software.

For further assistance, please visit the EPOMAKER support web사이트를 방문하거나 고객 서비스에 문의하세요.

5. 사양

6. 보증 및 지원

6.1 제품 보증

EPOMAKER products are covered by a limited warranty against manufacturing defects. Please retain your proof of purchase for warranty claims. The specific duration and terms of the warranty may vary by region and product. For detailed warranty information, please visit the official EPOMAKER web대지.

6.2 고객 지원

For technical support, product inquiries, or warranty service, please contact EPOMAKER customer support through the following channels:

• Web대지: 방문하세요 에포메이커 공식 스토어 for FAQs, drivers, and contact forms.
• 이메일: 제품 포장이나 공식 문서를 참조하세요. web최신 고객 서비스 이메일 주소를 확인하려면 해당 사이트를 방문하세요.

When contacting support, please provide your product model (Mini Cat 64) and a detailed description of the issue.