S866 전기 자전거 LCD 디스플레이 계기판 사용 설명서

1. 서론

The S866 LCD Display Meter is a versatile control panel designed for electric bicycles, compatible with 24V, 36V, and 48V systems. It provides essential riding data, allows for control of various e-bike functions, and features a clear, backlit display for visibility in various conditions. This manual will guide you through the installation, operation, and maintenance of your S866 display.

그림 1.1: 전면 view of the S866 LCD display meter, showing speed, battery, and trip information.

2. 설정 및 설치

The S866 LCD Display Meter is designed for easy installation on handlebars with a diameter of 22.2mm. Ensure your e-bike controller uses communication protocol No. 2 for compatibility.

2.1 패키지 내용

• S866 LCD Display Meter
• 장착 브래킷
• Waterproof Connector Cable

2.2 설치 단계

1. Secure the mounting bracket to your bicycle's handlebar (22.2mm diameter) using appropriate tools.
2. Slide the S866 LCD Display Meter onto the bracket until it clicks into place.
3. Connect the display's waterproof plug to the corresponding port on your e-bike controller. Ensure the connection is firm and secure.
4. Verify that your controller uses communication protocol No. 2. This display is only compatible with this protocol.

Figure 2.1: Diagram illustrating the S866 LCD display dimensions, bracket diameter (approx. 22.2mm), line length (approx. 21cm), waterproof grade (IP65), and communication protocol (No. 2).

Figure 2.2: The S866 LCD display mounted on an electric bicycle handlebar, demonstrating its compact size and clear visibility.

3. 사용 설명서

The S866 display provides various functions and information. Familiarize yourself with the buttons and display areas for optimal use.

Figure 3.1: Detailed diagram of the S866 LCD display panel, labeling buttons and display areas with corresponding functions.

3.1 버튼 기능

• + 버튼: Up button, used to increase values or assist levels.
• 전원 버튼: Power on/off button, also used to switch information.
• - 버튼: Down button, used to decrease values or assist levels.

3.2 기본 작업

• 전원 켜기/끄기: 잡아라 힘 button to power on. Hold it again to power off. If the e-bike is not used for more than 10 minutes, the display will automatically turn off (hibernation mode).
• 일반 인터페이스: 잡아라 힘 button to enter the normal interface.

3.3 고급 작업

Figure 3.2: Instructions for operating the S866 LCD display, including headlight control, assist level changes, 6km/h push mode, and multi-function area navigation.

• 헤드라이트 제어: 잡아라 + button to turn on the backlight and headlight simultaneously. Hold the + button again to turn them off.
• Change Assist Level: 를 누르세요 + or - button to increase or decrease assist levels. Level 1 is the lowest, Level 5 is the highest. Level 0 disables PAS mode. The display returns to the default assist level each time it powers on.
• 6km/h Push Mode: 잡아라 - button to enter 6km/h push mode, which moves the vehicle forward at a stable speed (approx. 6km/h). This is useful when pushing the vehicle. Release the button to exit this mode.
• Multi-function Area: 를 누르세요 힘 button to switch between different information displayed in the multi-function area: ODO (Odometer), TRIP (Trip Distance), VOL (Voltage), TIME (Ride Time), and back to ODO.

4. 파라미터 설정 모드

This is an advanced function. It is advised not to modify parameters unless you fully understand their implications, as incorrect settings can cause malfunction. Please read these instructions carefully before modifying and note down previous parameter values so you can restore them if needed.

Under the normal interface, press the + 그리고 - buttons simultaneously to enter parameter setting mode. The first screen shows P01. Press the 힘 button to switch to the next parameter, and press the + or - buttons to increase or decrease the value of each parameter. Press + 그리고 - 다시 이 모드를 종료합니다.

In this mode, there are a total of 20 parameters (P01-P20):

Figure 4.1: Parameter settings P01-P05 for the S866 LCD display, including backlight brightness, metric change, battery voltage, hibernate mode, and assist levels.

• P01: 백라이트 밝기 (1-lowest, 3-highest)
• P02: Change metric (0: KM; 1: MILE)
• P03: Select battery voltage (24V/36V/48V/60V, 36V by default)
• P04: Hibernate mode time (from 1 to 60 minutes, 0: never enter this mode)
• P05: Total assist levels (0: 3 levels; 1: 5 levels)

Figure 4.2: Parameter settings P06-P10 for the S866 LCD display, including wheel size, magnet number, speed limit, zero start, and driving mode selection.

• P06: Wheel size in inch (step: 0.1)
• P07: Number of magnets for speed calculation (range: 1-255)
• P08: Speed limit (range: 0-100km/h. This value is always in km/h even if the metric changed from km to mile.)
• P09: Zero speed start (0: zero stat; 1: Non zero start - means need to provide vehicle with initial speed then turn throttle will activate motor)
• P10: Driving mode selection (0: Only assist mode; 1: Only electric mode; 2: Both mode)

Figure 4.3: Parameter settings P11-P20 for the S866 LCD display, including assist sensitivity, starting power, disc type, current limit, low voltage protection, ODO reset, cruise mode, speed ratio, assist level 0, and protocol selection.

• P11: Assist sensitivity (range 1-24, sets the delay between pedaling and motor start; smaller value means the motor starts working after less pedal movement)
• P12: Assist starting power (range: 1-5, sets the starting power of the motor; bigger value means higher starting power)
• P13: Assist disc type (5 magnets, 8 magnets, 12 magnets)
• P14: Current limit of controller (range 1-20A, 12A by default)
• P15: 낮은 볼륨tage protection setting of controller
• P16: ODO distance reset (잡고 있다 + for 5 seconds to reset this value; hold - for 5 seconds to reset factory settings)
• P17: Cruise mode (0: cruise mode disabled; 1: cruise mode enabled; auto-cruise mode or cruise mode enabled by pressing 1 button - controller should be compatible. Auto-cruise mode is enabled automatically by holding the throttle position for several seconds - this function is realized by the controller)
• P18: Speed ratio (range: 50%~150%, used to correct the speed if the user finds it is not accurate)
• P19: Assist level 0 enable/disable (0: with level 0; 1: without level 0)
• P20: Protocol selection (0: NO.2 PROTOCOL; 1: SS PROTOCOL; 2: RESERVED; 3: RESERVED)

5. 유지관리

To ensure the longevity and optimal performance of your S866 LCD Display Meter, follow these maintenance guidelines:

• 청소: 디스플레이 화면과 본체는 부드러운 천으로 닦아주세요.amp cloth. Avoid using abrasive cleaners or solvents, as they may damage the ABS material or the screen.
• 물 노출: While the display is IP65 waterproof, avoid submerging it in water or exposing it to high-pressure water jets. Ensure the waterproof connector remains sealed.
• 연결 확인: 모든 케이블 연결부를 주기적으로 점검하여 안전하고 부식이나 손상이 없는지 확인하세요.
• 저장: If storing your e-bike for an extended period, keep the display in a dry, cool place away from direct sunlight.
• 충격 회피: Protect the display from physical impacts, which can damage the screen or internal components.

6. 문제 해결

This section provides solutions to common issues and explanations for error codes you might encounter.

6.1 오류 코드

The S866 display can show various error codes to indicate specific issues. Refer to the table below for their meanings:

Figure 6.1: Table listing S866 LCD display error codes (E00-E13) and their corresponding descriptions.

6.2 일반적인 문제 및 해결 방법

• 디스플레이 전원이 켜지지 않음:
  • 배터리가 충전되어 있고 제대로 연결되어 있는지 확인하세요.
  • Ensure the display cable is securely plugged into the controller.
• 잘못된 속도/거리 판독값:
  • Verify the wheel size (P06) and number of magnets (P07) settings in the parameter mode are correct for your e-bike.
  • Adjust the speed ratio (P18) if necessary.
• 모터가 응답하지 않음:
  • Check for error codes (E07, E08, E09).
  • Ensure the communication protocol (P20) is set to NO.2 PROTOCOL.
  • Verify assist sensitivity (P11) and starting power (P12) settings.
• Display Shows E10 Error:
  • This indicates a COM receive error. Ensure your controller uses communication protocol No. 2. The display is only compatible with this protocol.
  • Check the connection between the display and the controller.

7. 사양

Detailed technical specifications for the S866 LCD Display Meter:

• 모델: S866
• 호환 볼륨tage: 24V, 36V, 48V
• 디스플레이 유형: 액정표시장치
• 재료: 아크릴로니트릴 부타디엔 스티렌(ABS)
• 방수 등급: IP65
• Bracket Diameter: 약 22.2mm / 0.9인치
• 줄 길이: 약 21cm / 8.3인치
• 통신 프로토콜: Protocol No. 2
• 크기(패키지): 11.6 x 7.9 x 7.4cm
• 무게: 100그램
• 제조업체 참조: SPYMINNPOOwxb12da94k1645

8. 보증 및 지원

SPYMINNPOO is committed to providing quality products and customer satisfaction. If you have any questions or encounter issues with your S866 LCD Display Meter, please contact us.

8.1 Service Guarantee

If you have any questions about your S866 LCD Display Meter, you can contact us via email at any time. We are committed to responding and resolving your problems promptly, providing better service.

8.2 연락처 정보

For support, please refer to the contact details provided with your purchase or visit the official SPYMINNPOO brand store on Amazon: SPYMINNPOO Brand Store.