제품 끝view
The DEDRA SAS+ALL DED7051 18V Cordless Angle Grinder is designed for cutting and grinding tasks. This tool features a powerful motor capable of reaching speeds up to 8500 RPM, compatible with 125 mm and 115 mm diameter discs. Its ergonomic design, lightweight construction (2.2 kg), and fiberglass-reinforced nylon housing ensure durability and comfortable operation.
Key features include a safety switch that interrupts power if excessive pressure is applied to the workpiece, preventing damage or overheating. The quick-release system for discs, a two-position side handle, and a rubberized grip enhance user comfort and control. The disc changing key is conveniently stored within the side handle.
Image: DEDRA 18V Cordless Angle Grinder, showing the main unit with the side handle and disc guard installed.
안전 정보
이 전동 공구와 함께 제공되는 모든 안전 경고, 지침, 그림 및 사양을 항상 읽고 이해하십시오. 아래 나열된 모든 지침을 따르지 않으면 감전, 화재 및/또는 심각한 부상이 발생할 수 있습니다.
- 작업 영역 안전: 작업 공간을 깨끗하고 밝게 유지하십시오. 어수선하거나 어두운 곳은 사고의 위험이 있습니다. 가연성 액체, 가스 또는 먼지가 있는 곳 등 폭발 위험이 있는 환경에서는 전동 공구를 작동하지 마십시오.
- 전기 안전: 파이프, 라디에이터, 레인지, 냉장고와 같은 접지된 표면과의 신체 접촉을 피하십시오. 신체가 접지되거나 접지된 경우 감전 위험이 증가합니다.
- 개인 안전: Always wear eye protection. Use personal protective equipment such as dust masks, non-skid safety shoes, hard hats, or hearing protection for appropriate conditions.
- 도구 사용 및 관리: 전동 공구에 힘을 가하지 마십시오. 용도에 맞는 올바른 전동 공구를 사용하십시오. 올바른 전동 공구는 설계된 속도에서 작업을 더 잘하고 더 안전하게 수행할 것입니다.
- 안전 스위치: The grinder is equipped with a safety switch that cuts off power if excessive pressure is applied to the workpiece. This prevents damage to the tool and potential overheating. Do not attempt to bypass or disable this safety feature.
- 디스크 호환성: Only use grinding and cutting discs with a diameter of 125 mm or 115 mm that are rated for the grinder's maximum RPM.
상자 안에 무엇이 들어있나요?
패키지를 열 때 모든 구성품이 들어 있고 손상되지 않았는지 확인하세요.
- 1 x DEDRA 18V Cordless Angle Grinder (Main Unit)
- 1 x Auxiliary Side Handle
- 1 x Disc Guard
- 1 x Two-hole Wrench for Disc Change
- Note: Battery and charger are NOT included and must be purchased separately.
Image: A visual reminder that the battery and charger are sold separately from the angle grinder unit.
설정
- 측면 핸들 부착:
The auxiliary side handle can be screwed into either of the two threaded holes on the grinder's gear housing, depending on your preferred working position and hand dominance. Ensure it is tightened securely.
Image: The angle grinder with the side handle attached, demonstrating its position.
- Mounting the Disc Guard:
Position the disc guard over the spindle housing. Rotate it until it covers the disc adequately for your application, providing maximum protection. Tighten the guard's clamping mechanism firmly to prevent movement during operation.
- Installing the Grinding/Cutting Disc:
Ensure the grinder is switched off and the battery is removed before installing or changing discs. Press the spindle lock button to secure the spindle. Place the inner flange onto the spindle, then position the grinding or cutting disc onto the inner flange. Secure the disc with the outer flange and tighten it using the provided two-hole wrench. Release the spindle lock.
이미지: 상단 view of the angle grinder showing the disc guard and the spindle assembly where the disc is mounted.
- 배터리 삽입:
Align the battery pack with the battery slot at the rear of the grinder handle. Slide the battery into place until it clicks securely. Ensure it is fully seated before operation.
이미지: 후면 view of the angle grinder, highlighting the battery insertion slot.
작동 지침
- 그라인더 시작하기:
With the battery inserted and disc securely mounted, hold the grinder firmly with both hands. Press the power switch to start the tool. Allow the disc to reach full speed before making contact with the workpiece.
- 연삭 및 절단:
Apply light, consistent pressure. Do not force the tool. The integrated safety switch will activate and cut power if excessive pressure is detected, protecting the tool from overload and overheating. If this occurs, reduce pressure and restart the tool.
- 분쇄기 중지:
Release the power switch to stop the tool. Wait for the disc to come to a complete stop before setting the grinder down or performing any adjustments.
유지
- 청소: Regularly clean the ventilation openings of the grinder to prevent dust accumulation, which can lead to overheating. Use a soft brush or compressed air.
- 디스크 검사: Before each use, inspect the grinding or cutting disc for cracks, chips, or excessive wear. Replace damaged discs immediately.
- 저장: Store the grinder in a dry, secure place, out of reach of children. Remove the battery when storing for extended periods.
- 배터리 관리 : Follow the manufacturer's instructions for charging and storing the battery pack. Do not expose batteries to extreme temperatures or moisture.
문제 해결
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| 그라인더가 시작되지 않습니다. | 배터리가 올바르게 삽입되지 않았거나 방전되었습니다. | 배터리가 완전히 장착되었는지 확인하세요. 필요한 경우 배터리를 충전하세요. |
| 분쇄기가 작동 중에 멈춥니다. | Excessive pressure applied (safety switch activated). | Reduce pressure on the workpiece. Restart the tool. |
| 과도한 진동이나 소음. | 디스크가 잘못 설치되었거나 손상되었습니다. | Check disc installation. Replace disc if damaged or worn. |
| 도구가 뜨겁습니다. | Overuse or blocked ventilation. | Allow tool to cool down. Clean ventilation openings. |
명세서
| 기인하다 | 값 |
|---|---|
| 상표 | 데드라 |
| 모델 번호 | DED7051 |
| 전원 | 배터리 구동(18V) |
| 최대 RPM | 8500 RPM/min |
| Outer Disc Diameter | 125 Millimeters (also compatible with 115 mm) |
| 디스크 내경 | 22.2mm (XNUMXmm) |
| 재료 | Nylon (fiberglass-reinforced) |
| 품목 무게 | 2 킬로그램 |
| 패키지 크기 | 37 x 14 x 11cm |
| 배터리 포함 | 아니요 |
| 필요한 배터리 | Yes (Lithium-Manganese Dioxide type) |
보증 및 지원
Dedra products are designed for quality and reliability, undergoing testing at every stage of their lifecycle to ensure high standards. While specific warranty details are not provided in this manual, for any product support, technical assistance, or warranty claims, please contact Dedra customer service or refer to the official Dedra web최신 정보를 제공하는 사이트입니다.
You can visit the official Dedra store on Amazon for more information and contact options: Dedra Store