1. 서론
This manual provides detailed instructions for the safe and effective use of the GYS 059856 Paint Thickness Gauge. This portable device is designed for quick and easy measurement of non-magnetic coatings (such as paint or film) on metallic surfaces. It is an essential tool for various applications including the processing industry, automotive repair, metal treatment, chemical industry, and goods inspection.
기기를 작동하기 전에 이 설명서를 자세히 읽고 향후 참고를 위해 보관해 두십시오.
2. 안전 정보
- 사용하기 전에 항상 기기가 깨끗하고 건조한지 확인하십시오.
- 장치를 극한의 온도, 습도 또는 직사광선에 노출시키지 마십시오.
- 장치를 떨어뜨리거나 강한 충격을 가하지 마십시오.
- 직접 기기를 분해하거나 수리하지 마십시오. 정비는 자격을 갖춘 기술자에게 의뢰하십시오.
- 기기를 어린이의 손이 닿지 않는 곳에 보관하세요.
- 현지 규정에 따라 배터리를 책임감 있게 폐기하세요.
3. 제품 오버view
The GYS 059856 Paint Thickness Gauge features a compact design with an LCD display and intuitive controls.
그림 1: 전면 view of the GYS 059856 Paint Thickness Gauge. The device is yellow with a black LCD screen at the top. Below the screen are three black buttons: 'MODE' on the left, 'UNIT' on the right, and 'ZERO' with a power symbol in the center bottom.
3.1 주요 구성 요소
- LCD 디스플레이: Shows measurement readings, units, and mode indicators.
- MODE 버튼: Used to switch between measurement modes (Single, Continuous, Differential).
- 단위 버튼: Used to switch between metric (µm) and imperial (mils) units.
- 제로 버튼: Used for zero calibration and powering the device on/off.
- 측정 프로브: Located at the bottom of the device, used to contact the surface for measurement.
4. 설정
4.1 배터리 설치
Locate the battery compartment on the back of the device. Insert the required batteries, ensuring correct polarity. Close the battery compartment securely.
4.2 전원 켜기/끄기
를 누르고 계세요 영 button to power on the device. To power off, press and hold the 영 button again. The device also features an automatic shut-off function to conserve battery life.
5. 사용 설명서
The GYS 059856 offers three measurement modes and supports both metric and imperial units.
5.1 측정 단위 선택
를 누르세요 단위 button to toggle between metric (µm) and imperial (mils) units.
5.2 측정 모드
를 누르세요 방법 다음 측정 모드를 순환하려면 버튼을 누르십시오.
- 단일 측정 모드: Takes a single reading each time the probe is placed on the surface.
- Continuous Measurement Mode: 표면을 따라 프로브를 이동시키면서 지속적으로 측정값을 기록합니다.
- Differential Measurement Mode: Displays the difference between the current reading and a previously set reference value.
5.3 측정하기
- Ensure the surface to be measured is clean and free of debris.
- 원하는 측정 단위와 모드를 선택하십시오.
- Place the measurement probe firmly and perpendicularly onto the coated metallic surface.
- LCD 화면에 표시된 두께 값을 읽으십시오.
- Lift the device from the surface to prepare for the next measurement (in Single mode).
6. 교정
Accurate measurements depend on proper calibration. The device supports three calibration functions:
6.1 제로 캘리브레이션
This calibration is performed on an uncoated, bare metallic surface to establish a zero reference point. Place the probe on a clean, uncoated metal surface and follow the on-screen instructions or refer to the device's specific calibration sequence (usually involving the 영 단추).
6.2 XNUMX점 교정
This method uses two known thickness standards (e.g., a thin film and a thicker film) to calibrate the device across a range. This provides more accurate readings for varying thicknesses.
6.3 Easy Calibration
Refer to the device's specific instructions for "Easy Calibration," which may involve a simplified process for quick adjustments.
Note: Always calibrate the device before critical measurements or if you suspect inaccurate readings.
7. 유지관리
- 청소: 부드럽고 마른 천으로 기기를 닦으세요. 연마성 세제나 용제를 사용하지 마세요.
- 저장: Store the device in a dry, cool place, away from direct sunlight and extreme temperatures. If storing for extended periods, remove the batteries.
- 프로브 관리: Keep the measurement probe clean and free from scratches or damage.
8. 문제 해결
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| 장치의 전원이 켜지지 않습니다. | 배터리 잔량이 부족하거나 방전되었거나, 배터리 극성이 잘못되었을 수 있습니다. | 배터리를 교체하세요. 배터리 방향을 확인하세요. |
| 부정확한 판독값. | Device not calibrated; dirty probe; surface not clean; incorrect measurement mode. | Perform calibration; clean probe and surface; select appropriate measurement mode. |
| Display shows "OL" or "Err". | Measurement range exceeded; sensor error. | Ensure measurement is within device's range; restart device. If error persists, contact support. |
9. 사양
- 모델: GYS 059856
- 제조업체: GYS
- 제품 크기(길이 x 너비 x 높이): 10.5 x 6.1 x 2.8cm
- 무게: 137그램
- 측정 원리: Non-magnetic coating on metallic surfaces
- 측정 단위: Metric (µm), Imperial (mils)
- 측정 모드: Single, Continuous, Differential
- Calibration Functions: Zero calibration, 2-point calibration, Easy calibration
- 자동 차단 : 예
- ASIN: B09GS7G1N4
- 제조업체 참조: 059856
- 예비 부품 가용성: 정보가 없습니다
10. 보증 및 지원
For warranty information and technical support, please refer to the official GYS website or contact your local distributor. Information regarding spare parts availability is not provided in the product specifications.
GYS 공식 Web대지: www.gys.fr
