소개
This manual provides essential information for the safe and effective use of the ABB LTC Low Terminal Covers XT7 / XT7 M F 4P. These covers are designed for use with automatic switches in moulded boxes, specifically for fixed four-pole configurations. Please read this manual thoroughly before installation and operation.
안전 정보
경고: Electrical installation and maintenance should only be performed by qualified personnel. Failure to follow these instructions can result in serious injury or death.
- 기기를 설치하거나 정비하기 전에 항상 전원을 차단하십시오.
- 모든 연결이 안전한지 확인하고 현지 전기 규정을 준수하세요.
- 제품이 손상된 것으로 보이면 사용하지 마십시오.
- 어린이의 손이 닿지 않는 곳에 보관하세요.
패키지 내용
패키지에 모든 품목이 들어 있는지 확인하세요.
- 2 x LTC Low Terminal Covers XT7 / XT7 M F 4P
- 사용 설명서(본 문서)
Image: Two ABB LTC Low Terminal Covers. The top cover is shown from a slightly elevated angle, revealing its flat top surface with embossed patterns and ribbed side. The bottom cover is inverted, showing the internal structure designed to house electrical terminals, also with ribbed sides. Both covers are dark grey.
설정 및 설치
These terminal covers are designed for specific ABB automatic switches in moulded boxes (XT7 / XT7 M F 4P series). Follow the instructions provided with your main automatic switch for proper installation.
- 스위치 설치 준비: Ensure the automatic switch is properly mounted and all power is disconnected.
- 터미널 식별: Locate the low terminals on your XT7 / XT7 M F 4P automatic switch that require covering.
- 덮개 위치: Align the LTC low terminal cover with the corresponding terminals. The cover is designed to fit snugly over the terminal connections.
- 덮개를 고정하십시오: Gently press the cover into place until it clicks or is firmly seated. Ensure there are no gaps and the cover is securely attached.
- Repeat for all Terminals: Use the second cover for the remaining set of terminals if applicable.
- 설치 확인: Double-check that both covers are correctly installed and provide adequate protection for the terminals.
작동 지침
The LTC Low Terminal Covers are passive components designed to provide protection for electrical terminals. They do not have active operational functions. Once installed, their purpose is to insulate and protect the low terminals of the automatic switch from accidental contact and environmental factors.
- Ensure covers remain securely in place during operation of the automatic switch.
- Do not attempt to remove covers while the switch is energized.
유지
These terminal covers require minimal maintenance. Regular inspection is recommended to ensure their integrity and proper function.
- 청소: If necessary, clean the covers with a dry, lint-free cloth. Do not use abrasive cleaners or solvents.
- 점검: Periodically check for any signs of damage, cracks, or discoloration. Ensure they remain securely attached to the automatic switch.
- 대사: If a cover is damaged or no longer fits securely, replace it immediately with an authentic ABB replacement part (Model: 1SDA107476R1).
문제 해결
As passive protective components, troubleshooting for these terminal covers is limited. Most issues relate to improper installation or physical damage.
| 문제 | 가능한 원인 | 해결책 |
|---|---|---|
| Cover does not fit or is loose. | Incorrect model of cover for the switch; improper alignment; damaged cover. | Ensure you have the correct XT7 / XT7 M F 4P covers. Re-align and press firmly. Inspect for damage and replace if necessary. |
| Cover is cracked or broken. | Physical impact or stress. | Replace the damaged cover immediately to maintain safety and protection. |
명세서
| 기인하다 | 세부 사항 |
|---|---|
| 제품 참조 | ABB 1SDA107476R1 |
| 제품군 | Automatic Switch in Molded Box Accessories |
| 유형 | LTC Low Terminal Covers |
| 호환성 | XT7 / XT7 M F 4P Automatic Switches |
| 수량 | 2팩에 XNUMX개 |
| 치수 | Approximately 18 x 14 x 9 cm (for the package) |
| 무게 | Approximately 676 g (for the package) |
| 색상 | Multicoloured (as per product listing, typically grey) |
보증 및 지원
For warranty information and technical support regarding your ABB LTC Low Terminal Covers, please refer to the documentation provided with your main ABB automatic switch or visit the official ABB website. Ensure you have your product reference number (1SDA107476R1) ready when contacting support.
ABB 공식 Web대지: www.abb.com
