HGLRC Rekon7 Long Range PRO Frame Kit User Manual

소개

This manual provides detailed instructions for the assembly, setup, and maintenance of your HGLRC Rekon7 Long Range PRO Frame Kit. Designed for 7-inch FPV racing drones, this frame kit offers a robust and lightweight foundation for your long-range FPV build. Please read all instructions carefully before beginning assembly.

제품 끝view

The HGLRC Rekon7 Long Range PRO Frame Kit is engineered for durability and performance. Key features include a low-profile design to accommodate large batteries, and arms secured with sturdy M4 hardware. It is compatible with 20x20mm mounting holes for various flight controllers.

Included Components (What's in the Box)

Assembled HGLRC Rekon7 Long Range PRO Frame Kit, showcasing its carbon fiber structure and low-profile 설계.

상세한 view of all individual components included in the Rekon7 frame kit, laid out for identification.

• 1x 2mm top plate
• 1x 2mm base plate
• 1x 2mm mid plate
• 2x 6mm front arm
• 2x 6mm rear arm
• 2x 2mm rack protection board
• 2x 2mm camera side panel
• 2x M3*28mm black mesh aluminum column
• 4x M3*20mm black mesh aluminum column
• 2x M3*18mm black mesh aluminum pillar
• 4x M4*12 나사
• 4x M3*20 나사
• 4x M3*16 나사
• 4x M3*10 나사
• 8x M3*8 나사
• 4x M2*20 나사
• 1x M2*16 나사
• 2x M2*4 나사
• 1x M5 lock nut (red)
• 4x M3 셀프 잠금 너트
• 5x M2 셀프 잠금 너트
• 8x M3*8 shock-absorption balls
• 4x M2*4 shock-absorption balls
• 2x battery straps 20x250mm
• 1x Battery Anti-slip pad
• 1x TPU black GoPro holder mount
• 1x TPU black GPS mount
• 1x TPU black antenna mount
• 1x TPU black T-antenna mount
• 1x TPU black buzzer mount
• 1x TPU black DJI Air unit Block A
• 1x TPU Black DJI Air unit Block B

명세서

Note: Recommended parts (not included) are Flight control: Zeus F722, Motor: 2806.5, ESC: Zeus 48-60A, Camera: 19X19mm, Propeller: 7 inches, Battery: 6S 1800-4200mAh.

조립 설명서

Follow these steps to assemble your HGLRC Rekon7 Long Range PRO Frame Kit. Ensure you have all components listed in the "Included Components" section before starting.

1단계: 베이스 준비

1. Identify the 2mm base plate.
2. Attach the 6mm front arms and 6mm rear arms to the base plate using the appropriate M4 screws. Ensure the arms are securely fastened.

맨 아래 view of the Rekon7 frame, showing the arm attachment points and motor mounting holes.

Step 2: Install Middle Plate and Standoffs

3. Place the 2mm middle plate onto the base assembly.
4. Secure the middle plate using the M3 aluminum columns (28mm, 20mm, 18mm) and M3 self-locking nuts. Ensure the 20mm spacing between the top and middle plates is maintained for flight controller installation.
5. Install the 2mm rack protection board and 2mm camera side panels using the designated screws.

맨 위 view of the Rekon7 frame, illustrating the central mounting area for electronics and standoff placement.

Step 3: Mount Top Plate and TPU Parts

6. Attach the 2mm top plate to the aluminum columns, securing it with M3 self-locking nuts.
7. Install the TPU black GoPro holder mount, TPU black GPS mount, TPU black antenna mount, TPU black T-antenna mount, and TPU black buzzer mount in their respective positions.
8. Mount the TPU black DJI Air unit Block A and Block B if you are using a DJI Air Unit.

옆 view of the Rekon7 frame, highlighting the camera mount and overall profile.

4단계: 마무리 작업

9. Apply the Battery Anti-slip pad to the top plate.
10. Secure the battery straps (20x250mm) to the frame.
11. Double-check all screws and nuts to ensure they are tightened appropriately. Avoid over-tightening carbon fiber components.

Operating Your Drone (Frame Kit)

This product is a frame kit and does not operate independently. Once assembled with a flight controller, motors, ESC, camera, and battery (not included), refer to the instruction manuals for those individual components for proper operation and flight procedures. Ensure all electronic components are correctly wired and configured according to their respective manufacturer guidelines before attempting flight.

유지

Regular maintenance ensures the longevity and safety of your drone frame.

• 손상 여부 검사: After each flight, visually inspect the carbon fiber plates and arms for any cracks, delamination, or stress marks. Check TPU parts for tears.
• Check Screws and Nuts: Periodically verify that all screws and nuts are tight. Vibrations during flight can loosen fasteners.
• 프레임을 청소하세요: Use a soft, dry cloth to clean dust and debris from the carbon fiber. Avoid harsh chemicals that could damage the material.
• 팔 교체: In case of a crash, inspect arms thoroughly. Replace any damaged arms immediately to maintain structural integrity.

문제 해결

This section addresses common issues related to the frame kit itself. For issues related to flight performance or electronics, refer to the manuals of your specific flight controller, ESC, and motors.

• 느슨한 구성 요소: If any part of the frame feels loose after assembly or flight, re-tighten the corresponding screws and nuts. Use thread-locking compound if necessary, but apply sparingly to avoid damaging plastic parts.
• 진동: Excessive vibrations can sometimes be traced to loose frame components or damaged arms. Inspect all parts for damage and ensure everything is securely fastened.
• Difficulty Mounting Electronics: Ensure you are using the correct mounting hardware (screws, standoffs) for your flight controller and other components, matching the 20x20mm mounting patterns.

도움이 되는 동영상

These videos provide additional guidance for FPV drone assembly and related components. While not specific to the Rekon7 frame, they offer general insights into building practices.

보증 및 지원

For specific warranty information regarding the HGLRC Rekon7 Long Range PRO Frame Kit, please refer to the documentation provided with your purchase or visit the official HGLRC website. If you encounter any issues or require technical assistance, please contact HGLRC customer support through their official channels.

Note: Damage resulting from improper assembly, modification, or misuse is typically not covered under warranty. Always ensure proper handling and assembly.